Renu Electronics WP2 Lite Series User manual

0
WP2043TN
WP2070TN
WP2101TN
Product Code
WP2043TN: 4.3”, 480 x 272 pixels, WQVGA color TFT
with 4-wire analog resistive touch screen with serial port,
1 Ethernet port.
WP2070TN: 7”, 800 x 480 pixels, WVGA color TFT with
4-wire analog resistive touch screen with serial port, 1
Ethernet port.
WP2101TN: 10.1”, 1024 x 600 pixels, WSVGA color TFT
with 4-wire analog resistive touch screen with serial port,
1 Ethernet port.
WP2 Lite web panel is a Thin Client with an inbuilt Micro
browser ready to connect to a remote web server on the
network.
To use the WP2 Lite as a browser, follow these steps to
connect the device to a Webserver.
1. Power ON the WP2 Lite panel using a 24VDC power
supply.
2. Plug in the Ethernet cable into the RJ45 port.
3. After the device boots up, click on Settings 
Microbrowser and Network Settings.
4. On the new screen enter the Host address and the
start page on the host
Eg: Host: 192.168.1.50
Start Page: start.html
5. Click Back to go to the main page.
6. Click Start to load the web page.
Power (Base)
4.3“: 24VDC(+20%, -15%)
@250mA, 6W
7.0“: 24VDC(+20%, -15%)
@300mA, 7.2W
10.1“: 24VDC(+20%, -15%)
350@mA, 8.4W
Display
480 x 272pixels , 4.3" Color TFT,
WQVGA Web Panel Analog
Resistive Touch Screen
800 x 480pixels , 7" Color TFT,
WVGA Web Panel Analog
Resistive Touch Screen
1024 x 600pixels , 10.1" Color
TFT, WSVGA Web Panel Analog
Resistive Touch Screen
Memory
CPU: 32-bit ARM Cortex-M7
RAM: 32MB
Panel Cutout
80(H) x 111(W)mm
127(H)x175(W) mm
178(H)x256(W) mm
Dimensions
89(H) x 120(W) x 31.5(D) mm
138(H)x186(W)x31(D) mm
190(H)x268(W)x33(D) mm
Weight
Approx. 200gm, 400gm, 900gm
LED
1
Communication
Ethernet
1x10/100MBps
OSK
Yes
Environment & Approvals
Operating Temperature
0°C to 50°C
Storage Temperature
-20°C to 85°C
Humidity
10 to 95% (Noncondensing)
Shock
IEC 60068-2-27, 25g, 11ms, 6
shocks per axis, total 18 shocks
(X, Y, Z)
Vibration
5~150Hz, 3g peak, (X, Y, Z)
Protection
IP66 for front panel mounting
Approvals
CE, UL (Class 1 DIV 2) & RoHS
compliant
Supported Web Server
Spider Controls, Codesys2.x,
Codesys3.x
Specification
QUICK START GUIDE
WP2 Lite Web Panel
Getting Started
Panel Cutout Dimensions

Rev.
Description
Date
1.0
First Draft
07/11/2022
1.1
Updated Product Image
16/11/2022
RENU Electronics Pvt. Ltd®reserves the right to change
or discontinue specifications and features without prior
notice.
To view the latest and updated datasheets/manuals,
please visit www.renuelectronics.com.
CONTROL DRAWING NO# CNTL/DWG/WP2 Lite/001 VER.NO: 1.00
Communication
WP2043TN
Panel Cutout Dimensions: 111.00 (W) x 80.00(H) mm
Panel Thickness: Maximum 6mm
Mounting Clamps: 2
WP2070TN
Panel Cutout Dimensions: 127.00(H) x 175.00(W) mm
Panel Thickness: Maximum 6mm
Mounting Clamps: 4
WP2101TN
Panel Cutout Dimensions: 256.00 (W) x 178.00(H) mm
Panel Thickness: Maximum 6mm
Mounting Clamps: 6
Tighten the mounting screws evenly to a torque
between 0.4N/m to maintain water and dust resistance.
This section provides information regarding
communication interfaces supported by this product.
RJ45/Ethernet Port
The WP6 Plus series devices come with an in-built
RJ45/Ethernet port. The RJ45 port is a shielded female
jack with link and activity LEDs.
Pin number
Signal
1
TX+
2
TX-
3
RX+
4
NC
5
NC
6
RX-
7
NC
8
NC
Earthing
The optimum method for earthing electronic equipment is
to earth it separately from other high-power systems, to
earth more than one unit of electronic equipment with a
single-point earth. The earthing marked terminal (see
below) is provided on the unit.
[Note: Do not use an earth that has an unstable
impedance, such as painted screws or earth subject to
vibration.]
Revision History
WARNING
This equipment is suitable for use in Class I, Division 2,
Groups A, B, C and D or non-hazardous locations only.
WARNING - EXPLOSION HAZARD - Do not disconnect
equipment unless power has been removed or the area
is known to be non- hazardous.
WARNING - EXPLOSION HAZARD - Substitution of
components may impair suitability for Class I, Division 2.
The list of materials used in the construction of these
devices with name of sealed device - generic name of
the material and the supplier's name and type
designation.
It is recommended that the user periodically inspect the
sealed devices used, for any degradation of properties
and Replace the device ifany degradation is found.