Reolink Reolink Go PT Plus User manual

Go PT Plus
Reolink Go PT Plus is a 100% wire-free outdoor surveillance camera that runs on 4G
LTE and 3G networks. No WiFi needed. No wiring hassles. With an ultra-wide
viewing angle of 355° pan & 140° tilt, it can be a perfect security solution for large
areas warehouses, woods, etc. !
1. Specs
1
Speaker
2
6 IR LEDs
3
Status LED
4
Built-in PIR Sensor
5
Built-in Mic
6
Lens
7
Daylight Sensor

Status Light
Note:
If the camera connects the network successfully,there will be no status LED light
up during idle mode.
Status Light
Camera Status
Red LED solid light up then starts to
flash
Camera cannot recognize the SIM
card or there is PIN code of the SIM
card.
Red LED solid light up then flash
slowly about once every second
Camera cannot register the mobile
carrier network.
1
Antenna
2
Battery Status LED
3
Micro USB Port
4
Power Switch
5
Reset Hole
6
Nano SIM Card Slot
7
microSD Card Slot

Red LED solid light up then flash
quickly about 3 times in 1s
Data call failed or requires to input
the APN.
Red LED solid light up then blue LED
starts to flash and goes off completely
Network connection failed.
Red LED solid light up then blue LED
starts to flash and solid light up
Network connection succeed.
2. Setup and Install
Set up the Camera
What’s in the Box
Note: The package content may vary and update with different version and
platforms, please take the below information only for a reference. And the actual
package content are subject to the latest information on the product selling page.
Go PT Plus
Activate the SIM Card for the Camera
The SIM card shall support WCDMA and FDD LTE.
Activate the card on your smartphone or with your network carrier before inserting
it into the camera.
Bracket *1
Surveillance Sticker*1
Pack of Screws*1
Reset Needle*1
Mounting Template *1
Go PT Plus*1
Quick Start Guide*1
USB Cable*1
Pre-installed 32GB
microSD Card*1

Notes:
Some SIM cards have a PIN code, please use your smartphone to disable the
PIN first.
Do not insert the IoT or M2M SIM card into your smartphone.
Install the SIM Card
1. Rotate the camera lens, and remove the rubber cover.
2. Insert the SIM card.

3. With these done, press the rubber cover firmly for better waterproof
performance.
Notes:
• The SIM card slot is above the SD card slot. When inserting the SIM card in,
remember that the gold contacts shall face down and you need to push the
trimmed corner inside the camera.
• The SD card slot is below the SIM card slot. When inserting the SD card in,
remember that gold contacts shall face up.
Connect to the Mobile Carrier Network
1. With the SIM card inserted, you can turn on the camera.
2. Wait a few seconds and a red light will be on and solid for a couple of seconds.
Then, it will go out.

3. A blue LED will flash for a few seconds and then go solid before going out. You
will hear a voice prompt "Network connection succeeded”, which means the
camera has been successfully connected to the network.
Note:
You may also run into the following situations:
No.
Voice Prompts
Camera Status
Solutions

1
“SIM card cannot be
recognized”
Camera cannot
recognize this SIM
card.
1. Check if the SIM card is
facing the reverse
direction.
2. Check if the SIM card is
not fully inserted and
insert it again.
2
“The SIM card is locked
with a PIN. Please
disable it”
Camera cannot
recognize this SIM
card.
Put the SIM card into your
mobile phone and disable
the PIN.
3
“Not registered on
network. Please activate
your SIM card and check
the signal strength”
Camera fails to
register to the
operator network.
1. Check whether your
card is activated or not.
If not, please call your
operator to activate the
SIM card.
2. The signal is weak at
the current position.
Please move the camera
to a location with better
signal.
3. Check if you are using
the correct version of the
camera.
4
“Network connection
failed”
Camera fails to
connect to the
server.
The camera will be in
standby mode and
reconnect later.
5
“Data call failed. Please
confirm your cellular
data plan is available or
import the APN
settings”
The SIM card has run
out of data or APN
settings are not
correct.
1. Please check whether
the data plan for the SIM
card is still available.
2. Import the correct APN
settings to the camera.
Set up the Camera on the App
Please follow the steps below to do initial setup for the battery-powered cameras
via Reolink App.

Step 1. Tap the icon in the top right corner to add the camera.
Step 2. Scan the QR code on the back of the camera. If the phone doesn't respond,
please tap Input UID/IP below the scan window, and then enter the 16-digit UID
number under the QR code of the camera.
Step 3. Create the login password and name your camera. Then tap Next.

Step 4. Select a scene according to the place where your camera will be installed.
Then tap Next.
Step 5. Read the note and then tap Finish to complete the initialization of your
camera.

Now the initialization is finished and you can move it to the position you
want. Here is an article to choose a good position for the camera.
Install the Camera
We offer you guides on three different scenes in which the camera could be
installed. Check out them respectively.
Mount the Camera to the Wall
Step 1. Drill holes in accordance with the mounting hole template and screw the
security mount to the wall.
Note: Use the drywall anchors included in the package if needed.
Step 2. Screw the antenna to the camera.

Note: In order to get a better network connection, it is recommended to install the
antenna upward or horizontally.
Step 3. Screw the camera to the security mount and adjust to the proper direction.
Mount the Camera to the Ceiling
Step 1. Pull the button on the security mount and unscrew the bracket to separate
the two parts.
Step 2. Install the bracket base on the ceiling with screws.
Step 3. Align the camera with the bracket and turn the camera unit clockwise to
lock it in position.

Install the Camera with Loop Strap
You are allowed to strap the camera to a tree with both the security mount and
ceiling bracket. Thread the provided strap through the slots of the plate and fasten
it to a tree. Next, attach the camera to the plate as you have done in the previous
two methods.
Done! You've installed the Go PT Plus successfully.
Note: The best way to install the camera is to install it upside down in order to
prevent water from flowing into the microphone hole.

Reolink Solar Panel (Optional)
Reolink Solar Panels are specially designed to charge Reolink battery-powered
cameras, converting sunlight into electricity, which is is both cost-effective and
environmentally friendly. The more and stronger light that hits the solar panel, the
more electricity it produces.
1. Specs
Physical Parameters
Size: 185.4 x 120.4 x 6.5mm
Cable Length: 4 Meters
Weight: 280g
General
Charging Temperature: 0°C to 45°C (32°F to 113°F)
Operating Temperature: -10°C to 55°C (14°F to 131°F)
Weather Resistance: IP65 certified weatherproof
Max Output Voltage: 6V; Standard Working Voltage: 6V ± 0.3V
Max Current: 530MA
2. Install the Solar Panel
What's in the Box
Solar Panel ×1
Bracket ×1
Screws (in pack) ×1
Mounting Template ×1
Note: The package content may vary and update with different version and
platforms, please take the below information only for a reference. And the actual
package content are subject to the latest information on the product selling page.
Install the solar panel
Step 1. Please choose a location for your solar panel that gets the most sunlight
throughout the year. The Reolink solar panel needs only a few hours of direct
sunlight to sufficiently power up your camera daily. The amount of energy
that the solar panel can produce is affected by weather conditions, seasonal
changes, geographic locations, etc.

Step 2. Mount the bracket with the mounting template and the screws provided in
the package.
Step 3. Slot the solar panel into the bracket and make sure it's secure.

Step 4. Loosen the adjustment knob on the bracket, and adjust the angle of the
solar panel to receive the most direct sunlight. Then re-tighten the adjustment
knob to secure the panel.
Step 5. Connect the solar panel to the camera with the micro USB cable
Notes:
Make sure the solar panel is not blocked. The energy harvesting efficiency
drops drastically even when a small portion of the solar panel is blocked.
Please don’t install the solar panel completely horizontally. Otherwise your

solar panel might accumulate dust and other debris easily. It’s advised to
install the solar panel angularly to receive the most direct sunlight.
Wipe the solar panel regularly to remove dust or debris.
Please charge the batteries in temperature between 0°C and 45°C (32-113°F).
The solar panel won't charge the camera at temperatures below 0°C (32°F).
Make sure the camera is plugged in all the way and that the waterproof wire
cover protects the interface between the camera and the solar panel.