resi-linx RL-BV1000 User manual

®
WARRANTY
Vcomm Pty Ltd states that the warrant that the customer can rely on is that
provided by the manufacturer. In the event of any warranty claim please
contact us and we will forward it to the manufacturer. The manufacturer will
then determine the extent of their liability. This expressly negates, to the
extent possible by Australian law, any warranty reliance on Vcomm Pty Ltd.
RL-BV1000
AV Distribution Range
‘linx-AV’ 4 x 8 Composite Matrix Switch
www.resi-linx.com
ABN: 99 091 281 524
Vcomm Pty Ltd
Cable Requirements
4 pair twisted cable
Hardware Connection
1. Ensure all power to equipment is switched off prior to
installation.
RL-BV1000
2. Connect RCA cable from Video terminals 1 A of
Transmitter to the Composite Video terminal of AV
Source.
3. Connect 3.5mm Audio cable from Audio terminals 1 B
of Transmitter to the Analogue Audio terminals of the AV
Source.
4. Repeat steps 2 - 3 for Source 2 - 4 inputs.
5. Connect RL-IR700/800* IR emitter to Common output F
of Transmitter. Place the other end within 25cm of the IR
receiver on the AV source (depending on environmental
conditions).
6. For Discrete IR control, connect RL-IR700/800 IR emitter
from Discrete output 1 or 2 E and place emitter
head in front of IR Receiver of the desired device using
RL-ACC160* IR Emitter Shield. Choose which Discrete
IR source is to be controlled in each zone. Select via Dip
Switch D Discrete Emitter output port 1 or 2 and the
corresponding zone A, B etc.
7. Connect RJ45 socket C (output A) of Transmitter to
RJ45 input C of Receiver in Zone A.
RL-BV150B
8. Connect Video lead (yellow to yellow) from RCA Video
output I of Receiver to the yellow RCA Video input on
AV device (TV, etc).
9. Connect Audio lead L & R RCA connectors (red and
white) from output J on Receiver, to the corresponding
RCA Audio inputs on the AV device.
10. Connect RL-BV500* IR target to input K on Receiver.
Flat target can be easily mounted (either directly using
adhesive backing, or by using RL-ACC150* Target
Mount) to the desired location, anywhere within the line
of sight of remote controls.
11. Repeat steps 5 - 10 for connection of zones B - H.
12. Connect supplied 12V DC switch mode power pack to
power input G on Transmitter.
13. Once installation is complete, switch on power to all
equipment. Indicator LED’s will illuminate to show which
Source 1 - 4 is selected in each of the Zones A - H.
* Sold separately
A RCA Video output
B RCA Audio output
C RJ45 socket
D Discrete IR Select switch
E Discrete IR Emitter outputs
F Common IR Emitter outputs
G 12V DC Power input
H Indicator LED’s
I RCA Video output
J RCA Audio output
K IR Target input
ABDC
E F
G
4
12V DC
INPUT
IR REPEATERS
AUDIO
VIDEO
A
1C
1
2
IR SELECT
ABCDEFGH
3
2 4
1 3
2
2
1
COMMON
D
B F H
E G
SOURCE
A B C D E F G H
RL-BV1000
IR
OUTPUT
1
2
3
4
H
RL-BV150B
C
K
J
I
INSTALLATION MANUAL
Transmitter
Receiver

®
WARRANTY
Vcomm Pty Ltd states that the warrant that the customer can rely on is that
provided by the manufacturer. In the event of any warranty claim please
contact us and we will forward it to the manufacturer. The manufacturer will
then determine the extent of their liability. This expressly negates, to the
extent possible by Australian law, any warranty reliance on Vcomm Pty Ltd.
RL-BV1000
AV Distribution Range
‘linx-AV’ 4 x 8 Composite Matrix Switch
www.resi-linx.com
ABN: 99 091 281 524
Vcomm Pty Ltd
INSTALLATION MANUAL
Connection to zones B - H
as above
Zone A
RL-BV150B
Remote
Control
RL-BV500
RL-BV1000
Troubleshooting
IR LED indicator on RL-BV1000 Transmitter illuminates
briefly upon receipt of IR commands.
NOTE: Some brands of TV/Monitors can reduce the
range of the IR Receiver head, which is outside the
scope of the warranty.
RL-BV1000
Power 12V DC 1.5A Switch Mode
Maximum video input 1.2V P-P
Return loss >15dB to 1,000 MHz
Common mode rejection >40dB @ 1,000 MHz
Maximum distance cable Up to 100m
Video Signal Composite
Audio Signal Analogue
Conguration 4:8
IR capability Yes
Connections In/Out 2 sets - 4 x RCA
8 x RJ45
6 x IR Emitter
4 x 3.5mm Audio