Shinybow USA SB-5669CKP User manual

SB-5669CKP
16x16 HDMI & HDBaseT™4K2K Over Single CAT5e/6/7
Matrix Routing Switch with PoH (Power Over HDBaseT™)
INSTRUCTION MANUAL
IMPORTANT WARRANTY INFORMATION.
If you remove the HDMI screw posts, you must use the provided
HDMI Locking Post replacement screws to keep the internal HDMI
jack secure. Removing the HDMI screws without installing the
HDMI Locking Post replacement screws will void your warranty.

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

CONTENTS
INTRODUCTION .............................................................1
FEATURES.......................................................................2
PACKAGE CONTENTS .................................................. 2
SPECIFICATIONS............................................................3
FRONT PANEL ............................................................... 4
BACK PANEL ................................................................. 8
HDBASET™I/O TRANSMISSION & CABLE EXTENSION
LENGTHS.......................................................................12
REMOTE CONTROL .................................................... 13
IR REMOTE CODE LIST ............................................... 14
ROOM IR REMOTE CODES ......................................... 17
RS-232 / ETHERNET PROTOCOL ................................ 19
EDID FUNCTIONS ......................................................... 20
IR EXTENDER ............................................................... 27
TYPICAL APPLICATIONS ............................................. 28
HDBASET™APPLICATION ........................................... 32
INTRODUCTION
The SB-5669CKP is a professional 16x16 matrix routing switch.
Supporting (16) HDMI Inputs and (16) HDMI Outputs & (16)
HDBaseT™Outputs with PoH. The SB-5669CKP is based on the
HDBaseT™standards and supports full resolution HDMI video with
embedded HDCP, RS-232 and Bi-directional IR all over a single
CAT6/6a/7 category cable. With a signal bandwidth of 340Mhz,
there is no signal degradation. High denition digital signals can
be selected and distributed to any of the (16) Inputs to any of
the (32) Outputs simultaneously (channel outputs mirrored). The
switcher is fully CEC, HDCP 1.3, HDMI1.4a certied with HDMI
4K2K@30Hz, DVI 1.0, 3D formats and a wide frequency range
of 25MHz~340MHz. Supports UXGA/WUXGA/DVI 1920x1200
resolutions to any HD display. The SB-5669CKP has (16) HDMI
connector Inputs and (16) HDBaseT™(PoH) & (16) HDMI Outputs,
effectively making this a (16) In by (32) Out switcher (same signal
on both outputs). Using the HDBaseT™output remote transmitter,
it will allow you to connect a source in a remote location. Likewise,
the HDBaseT™Output and our HDBaseT™receiver, allows you to
connect a display in a remote location. EDID management can
be selected between (7) different modes. Control is provided via
front panel push buttons, IR remote, RS-232 or TCP/IP (not a
web-browser). A RS-232 Windows GUI interface is provided for
matrix routing control (Windows only).
1
HDMI-HDBaseT™4K2K Matrix Routing Switch Series
Thank you for purchasing the SB-5669CKP HDMI-HDBaseT™ Matrix Switcher. You will nd this unit easy to install and
highly reliable but it is essential that you read this manual thoroughly before attempting to use the 16x16 HDMI-HDBaseT™
Matrix switcher.
TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise — without express written permission and consent.
© Copyright 2017. All Rights Reserved.
Version 1.3 SEPT 2017
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.

FEATURES
Based on HDBaseT™, bi-directional IR and RS-232 interface. Full resolution HD Video, all HDBaseT™signals and PoH over single
CAT6/6a/7 category cable.
• Enables switching of (16) HDMI digital source devices to (16) HDMI devices and (16) HDBaseT™Transmitter Outputs (PoH) to (32)
total destinations
• HDBaseT™ specications with Bi-Directional IR, RS-232, Multi audio format and HD video signals over single CAT6/6a/7 category cable
• HDMI digital video w/ embedded HDCP, DVI format and CEC/HDCP 2.0 compliant
• Worldwide EDID control modes for HDMI full 4K2K HD Video resolutions
• Wide frequency range of 25MHz ~ 340MHz, Supports HDMI 4K2K@30Hz, HDMI 1.4a
• Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV HDMI resolutions 480i/480p, 576i/576p, 720p,
1080i/p & 4K2K (24/30Hz)
• Compatible with all HDMI source devices, PC monitors, Plasma HD displays, HDTVs and audio receivers or audio ampliers
• Digital video TMDS formats resolutions up to 4K2K with Deep color 36-bit
• Digital audio support digital multi-channel audio: Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex, DTS, DTS-HD, DTS-HD Master,
DTS-EX, PCM, PCM2, LPCM2
• HDBaseT™supports IR remotes and RS-232 signals over a single CAT6/6a/7 category cable
• Various User Interface Controls:
• Windows based GUI control via RS-232 port interface WIN2000/XP/WIN7-32/WIN7-64
• Front panel push buttons
• IR wireless remote controls
• Ethernet switch control (via pc protocol COMMANDS)
• Third party RS-232 control (via simple ASCII)
• Supports (7) world wide control function keys: Full function front panel controls: ALL / OFF / EDID / LOCK / RECALL / MEMORY / ENTER
• Supports EDID modes:
• a. Embedded EDID Modes: FSS (Fast Speed Start) / H24-3D/ H24-3D-M/ H36-3D/ H36-3D-M/ 4K2K-3D / DVI-D 1920x1200-60Hz
• b. External Modes: Learning mode (learning destination EDID link to source device)
• Automatic scanning input & output status via LCM showout on front panel
• Using the build-in booster, each HDMI Output port is capable of driving cable lengths of 1080p up to 98 ft (30M) & 4K2K up to 66 ft (20M)
• Supports IR remotes and IR extenders for a distance of up to ~ 984 ft (300M) Maximum
• Supports universal power adaptor AC100V~AC240V, 50/60Hz
The switcher will remember that last state during a power cycle. When power is removed and resorted, the last conguration will be invoked.
PACKAGE CONTENTS
Check that you have the following components:
• SB-5669CKP Matrix Switcher (Power Over HDBaseT™)
• RS-232 V2.0 / Ethernet V1.0 Protocol Instructions
• IR Remote Control (SW-5669)
• (16) Individual Remote Controls (SW-5669CK-IR01~IR16)
• 19 inch Ear mount bracket (Part # 4U-440L)
• SB-100 IR Extender Receiver Set
• CD Contents: This manual, Windows GUI, ISP V1.0 Windows driver
• RS-232 Cable 6.5 feet (2M)
• HDMI Locking Post Replacement Screws
• Users Guide
• Worldwide Universal Power Supply 100~240VAC, AC 50/60Hz
• Optional: SB-100C IR Extender Receiver Cable (6.5ft (2M))
SB-6335R series HDBaseT™Receiver sold separately
2
FEATURES & CONTENTS

SPECIFICATIONS
• Type of HDMI Switcher: (16) HDMI Inputs to (16) HDMI & (16) HDBaseT™Outputs Matrix Switcher
• HDMI Supports: HDMI 4K2K@30Hz, 1080p@60Hz, H36-bit Deep color, 3D, HDMI V1.4 formats
• HDBaseT™Support: HDMI digital signals, bi-directional IR, RS-232 and PoH over single CAT6/6a/7 cable
• HDCP/CEC Support: HDCP 1.3 Compliant, CEC Compliant
• Video Bandwidth: Double Data Rates: 340Mhz
• Digital Video Support: HD: 480i/ 480p/ 720p/ 1080i/p and 4K2K up to 36bit deep color
• Inputs (HDMI): (16) HDMI (HDMI or DVI digital source)
• Outputs (HDMI): (16) HDMI (to destination)
• Booster (Each HDMI Output): 1080p up to ~98 feet (30M) & 4K2K up to ~66 feet (20M)
• HDBaseT™Output (PoE): (16) HDBaseT™Transmitter (PoE) via a single category cable using RJ-45 connectors
• HDMI Digital Multi-Channel Audio Support: Multi Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital
Plus, DTS, DTS-ES 6CH, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• HDBaseT™Control:
• 1. IR Control:
• (16) IR In (Sends IR signals to (16) rooms via a HDBaseT™Transmitter)
• (16) IR Out (Links to receive IR signals from (16) rooms via a HDBaseT™Extender)
• 2. RS-232 I/O Control: (16) RS-232 I/O (Controls (16) rooms with RS-232 via the switchers HDBaseT™Extender Tx)
• Switch Controls:
• Select & Function buttons on front panel (Data status via LCM panel show out)
• IR Remote Control (switch control) (p/n: SW-HD69CK)
• (16) IR Room Remote Controls (switch control) (p/n: SW-HD69CK01~16)
• IR External port (switch control via 3.5mm OD Jack)
• RS-232 series interface (switch control)
• Ethernet series interface (switch control)
• Source Status: Input status LEDs indicates presence of a live signal
• (39) Function Control Keys: 1. ALL, 2. OFF, 3. RECALL, 4. ENTER, 5. MEMORY, 6. LOCK, 7. EDID, 8. Destination 1 thru 16, 9.
Source 1 thru 16
• (7) EDID Management: Select Embedded EDID Modes: Mode1: Fast Speed Start®, Mode2: H24-3D, Mode3: H24-3D-M, Mode4:
H36-3D, Mode5: H36-3D-M, Mode6: 4K2K-3D, PCM-2CH, Mode7: DVI-D 1920x1200
• Learning Mode:
• 1. Select LEARNING mode-1: Learning single Destination EDID to Link Source
• 2. Select LEARNING mode-2: Learning multiple Destination EDID to Link Source
• Infrared Frequency: 38Khz
• IR External Distance: SB-100 (~984 feet / 300M maximum)
• HDBaseT™Extender Distance: ~328 feet / 100M maximum
• HDMI I/O Connector: HDMI Type A - SMD 19pin female type
• Temperature: Operating Temperature 32°F - 100°F (0°C - 32°C)
• Dimensions (LxWxH): 17.5 x 12 x 7 in
• Rack Mount: 4RU High 19 in Rack Mount #4U-440L (with rack mount ears)
• Power Supply: AC 100~240VAC 50/60Hz (120V/3A/360W; 220V/1.63A/360W)
• Safety Approvals: CE, FCC, REACH
• Weight: 16.8 lb (Unit only) / 32.0 lb (Net)
As product improvements are continuous, specications are subject to change and without notice.
3
SPECIFICATIONS
IMPORTANT WARRANTY INFORMATION.
If you remove the HDMI screw posts, you must use the provided HDMI Locking Post replacement screws to keep
the internal HDMI jack secure. Removing the HDMI screws without installing the HDMI Locking Post replacement
screws will void your warranty.
LOOK A PUPPY!! NOW READ THIS!!

4
FRONT PANEL
FRONT PANEL
1. POWER ON SWITCH: The power switch turns the unit on and off. The LCM will illuminate blue to indicate the switcher is ON and receiving
power. The switcher will remember the last setting during a power cycle. When power is removed and resorted, the last conguration will
be evoked.
2. STATUS DISPLAY: Front panel status display shows current matrix routing conguration. This same display also shows particular
conguration settings depending on your current function. In run mode (as shown above), the display shows each Output (destination)
channel and which input (source) it is assigned.
3. IR SENSOR: The IR sensor receives IR commands from the supplied remote control or a third party IR emitter.
4. INPUT STATUS DISPLAY: Input sources 1 to 16 LED illuminates blue to indicate that a video source is present on that input.
5. SOURCE SELECT BUTTONS: Separate inputs 1 thru 16 select buttons are provided each source selection.
6. EDID MODE SELECT BUTTONS: Used to select EDID mode using buttons Source button #1 or #2.
7. DESTINATION SELECT BUTTONS: Separate outputs 1 thru 16 select buttons are provided for each destination assignment. Routing can be
source to destination or one source to multiple destinations.
Example: Press Destination 1, 8, 12 then press Source 2. This will route Input 2 to Output 1, 8, 12 respectfully.
8. 19 INCH EAR MOUNT PAIR: Converts desktop to 19 inch rack mount. Bracket (part # 4U-440L) INCLUDED. Image shows rack mount
bracket attached.

5
FRONT PANEL
FRONT PANEL
9. FUNCTION KEY - ALL:
Disables (mutes) video on all destinations OR assigns the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show ”0” to indicate none of the
destinations are assigned a video source.
Option 2
- Press ALL followed by Source 1 THRU 16. The display will show the source selected.
- Press ENTER. The pre-set source selection will be assigned all destinations.
10. FUNCTION KEY - OFF:
Disables (mutes) video on the selected destinations.
- Press OFF button followed by any Destination channel.
- Press 1 THRU 16 output destination. The display will show “0“ for the selected channel,
indicating no video selected.
- Press ENTER. The pre-set conguration will execute.
11. FUNCTION KEY - RECALL:
The system will show previously stored presets, up to a total of (32). Presets are stored in
local memory using Source keys 1 thru 16 or Destination keys 1 thru 16 as the memory
preset location.
- Press RECALL button.
- Press 1 THRU 16 on either Source or Destination row.
- Press ENTER. The pre-set conguration will execute.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.
- Or press RECALL again to cancel the operation.
12. FUNCTION KEY - ENTER: Press ENTER to conrm entries.

6
FRONT PANEL
FRONT PANEL
13. FUNCTION KEY - MEMORY:
The system will show stored presets, up to a total of (32). Presets are stored in local memory
using Source keys 1 thru 16 or Destination keys 1 thru 16 as the memory preset location.
- Congure desired matrices.
- Press MEMORY button.
- Press 1 THRU 16 on either Source or Destination row.
- Press ENTER to ready memory location.
- Or press MEMORY again to cancel operation.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.
- Or press MEMORY again to cancel the operation.
14. FUNCTION KEY - LOCK:
- Press and hold LOCK button for two seconds lock out the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
15. FUNCTION KEY - EDID:
- Press EDID to begin setting up your EDID mode. Use source row buttons #1 and #2 to
cycle thru the options. (Go to EDID setup instructions.)

7
FRONT PANEL
FRONT PANEL
16. SELECT (7) EMBEDDED EDID MODES:
Used to display/change current EDID mode.
- Press EDID to select new EDID mode.
- Press SOURCE row #1 or #2. Select (7) Embedded EDID modes.
- Press ENTER to ready memory location.
- Or press EDID again to cancel the operation.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.
SELECT LEARNING MODE-#1:
Select external LEARNING EDID mode-#1 (Single mode)
- Press EDID to select new Learning EDID mode-#1.
- Press DESTINATION again, press the same Destination #1 THRU #16 to learn the
HDBaseT™EDID out port. The EDID for HDBaseT™(CATx) has been learned.
- Press SOURCE, Press Source row #1 THRU #16. The switcher will learn the HDMI or
HDBaseT™EDID destination and pass to the select sources.
- Press ENTER to ready memory location.
- Or press EDID again to cancel the operation.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.
SELECT LEARNING MODE-#2:
Select external LEARNING EDID mode-#2 (Multiple mode)
- Press EDID to select new Learning EDID mode-#2.
- Press OFF, the LCM show Learning mode #2 status.
- Press DESTINATION button #1 THRU #16 to setup learning mode-#2. The LCM will
show “L”. The HDMI or HDBaseT™EDID destination for (CATx) has been learned.
- Press ENTER to ready memory location.
- Or press EDID again to cancel the operation.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.

8
BACK PANEL
BACK PANEL
1. DC POWER INLET: The switcher is tted with a AC power plug input
connector. Ensure that the plug used is of an approved type and
is of sufcient current carrying connector capacity with the correct
voltage and connector polarity. 100~240Volt AC, 50/60Hz power
supply.
2. IR EXTENDER CONTROL: Supports one IR extender. Extends a
maximum distance of up to ~984 feet/300M. When you plug the
external IR extender into the switcher, the front panel IR receiver
remains active.
3. RS-232 CONNECTION: RS-232 control port allows for interfacing
to a PC, such as a computer or touch panel control, to the switcher
via the DB-9pin female connector for serial RS-232 control.
4. ETHERNET CONNECTION: ETHERNET control port allows for
TCP/IP interfacing to a PC, such as a computer or touch panel
control (not a web-browser), to the switcher via the RJ-45 female
connector to control the switcher.
POWERSOCKET: Connector Type: IEC 60320 C13
IR EXTENDER JACK:Female jack - inner OD Ø
3.5mm
REMOTE PORT: DB-9pin female connector
REMOTE PORT: Control the switcher via the
RJ-45 female connector
ETHERNET PORT:
Note: The Ethernet port and RS-232 port
cannot be used simultaneously. Any
connection to the Ethernet port will disable
serial commands sent to the RS-232 port.

9
BACK PANEL
BACK PANEL
5. INPUTS - 1 ~ 16 HDMI: Connects a HDMI signal source to the Input.
The HDMI port supports HDMI with embedded audio and DVI with
AUX audio sources. If you remove the HDMI screw posts, you
must use the provided HDMI Locking Post replacement screws to
keep the internal HDMI jack secure. Removing the HDMI screws
without installing the HDMI Locking Post replacement screws will
void your warranty.
6. HDMI OUTPUTS 1 ~ 16: Connects a HDMI signal source to the
Output. The HDMI port supports HDMI with embedded audio and
DVI with AUX audio. If you remove the HDMI screw posts, you
must use the provided HDMI Locking Post replacement screws to
keep the internal HDMI jack secure. Removing the HDMI screws
without installing the HDMI Locking Post replacement screws will
void your warranty.
HDMI CONNECTOR: HDMI Type A SMD 19pin
female socket connector
Note: With the proper adapters, the
switcher can be used with DVI digital video
signals, as it is HDCP compliant.
HDMI CONNECTOR: HDMI Type A SMD 19pin
female socket connector
Note: With the proper adapters, the
switcher can be used with DVI digital video
signals, as it is HDCP compliant.

10
BACK PANEL
BACK PANEL
7. OUTPUT - 1 ~ 16 HDBASET™(TRANSMITTER): Sends (16) HDMI
and control signals via (16) HDBaseT™Transmitters to link (16)
external HDBaseT™Receivers.
Switcher uses (16) HDBaseT™Transmitter Outputs #1 ~ #16 with
PoE (optional) RJ-45 via CAT6/6a/7 category cable. Controls IR
input/output signals and RS-232 between the switcher and the
HDBaseT™Receiver.
HDBASET™TRANSMITTER CONNECTOR: (16)
RJ-45 jack 8P8C female socket
Link LED:
Solid = valid link
Flash = attempting to link
Off = no link established.

11
BACK PANEL
BACK PANEL
8. HDBASET™RS-232: 1~16 CONNECTION: (16) RS-232 control
ports allow for interfacing to a PC. Controls I/O via the switchers
HDBaseT™Transmitters to (16) rooms each via the D-Bub 9pin
female socket for serial RS-232 control.
9. HDBASET™LAN CONNECTION: All Tx LAN: Provides Ethernet
(LAN) connection from the switcher to All HDBaseT™Transmitters
(ie. SB-6335T5).
10.HDBASET™IRINPUT:1~16REMOTEIRSIGNALTOROOM: Sends (16)
IR signals to (16) rooms via the switchers HDBaseT™Transmitters.
When you plug the switchers HDBaseT™IR Transmitters into the
external port, the room IR HDBaseT™receiver remains active.
11. HDBASET™IR OUTPUT: 1~16 REMOTE IR SIGNAL FROM ROOM:
Receives (16) IR signals from (16) rooms each via the switchers
HDBaseT™Transmitters. When you plug the switchers HDBaseT™
IR Transmitters into the external port, the room IR HDBaseT™
receiver remains active.
REMOTE PORT: DB-9pin female connector
ALL HDBASET™TX LAN PORT CONNECTOR:
HDBaseT™Phone-Jack 8P8C, RJ-45 female
socket
LAN CONTROLS: Note: From the switcher to
the HDBaseT™Transmitter.
IR EXTENDER JACK: Female jack - inner OD Ø
3.5mm
IR EXTENDER JACK: Female jack - inner OD Ø
3.5mm

12
HDBASET™I/O TRANSMISSION & CABLE EXTENSION LENGTHS
HDBASET™I/O TRANSMISSION
Category Cable Lengths via Switcher and HDBaseT™Receiver
Cable Type
Resolution
Pixel clock rate
(MHz)
CAT5e
(70M)
CAT6
(100M)
CAT6
(100M)
1024x768@60Hz 65.00 MHZ Yes Yes Yes
1280x720p@60Hz 73.84 MHZ Yes Yes Yes
1920x1080i@60Hz 74.25 MHZ NA NA NA
1280x1024@60Hz 108.00 MHZ Yes Yes Yes
1920x1080p@60Hz 148.50 MHZ Yes Yes Yes
1920x1200@60Hz 152.90 MHz Yes Yes Yes
1600x1200@60Hz 162.00 MHZ Yes Yes Yes
Blue-Ray DVD player 1080p 174.00 MHz Yes NA Yes

13
REMOTE CONTROL
Before making any connections observe the following:
• Ensure the main voltage supply matches the label on the supplied plug-pack (+/-10%).
• Ensure that the power switch is OFF.
• Ensure that all system grounds (earth) are connected to a common point.
• Avoid powering equipment within a system from multiple power sources that may be separated by large distances.
• Connect all audio video sources and destination equipment.
• Power up all source and destination audio-visual sources.
• For each destination output select the appropriate input source by using the front panel input select buttons. The supplied IR remote
control. Or through the RS-232 serial communications port.
• Upon powering up the switcher, it will return to its last used setting before being powered down.
REMOTE CONTROL
1. & 2. SWITCH POWER ON or OFF:
Power ON and OFF
3. DESTINATION: 1 THRU 16 OUTPUT SELECTION:
Destination buttons to select the output display channel
4. SOURCE : 1 THRU 16 INPUT SOURCE SELECTION:
Inputs 1~16 source selection buttons
5. FUNCTION KEY: Function selection buttons
ALL OFF EDID RECALL
ENTER MEMORY LOCK

14
REMOTE PROTOCOL COMMANDS
IR REMOTE CUSTOM AND DATA CODES (NEC Standard)
HOW TO SETUP IR CODES : CUSTOM CODE : 5BA4
POWER ON: 5BA4 A15E ALL: 5BA4 B04F RECALL: 5BA4 B24D
POWER OFF: 5BA4 A25D OFF: 5BA4 B14E MEMORY: 5BA4 B44B
EDID: 5BA4 B748 LOCK: 5BA4 B54A ENTER: 5BA4 B34C
HOW TO GIVE IR COMMANDS:
PRESS DESTINATION - # then PRESS SOURCE - #
DESTINATION #1 : 5BA4 10EF SOURCE #1 : 5BA4 20DF
DESTINATION #2 : 5BA4 11EE SOURCE #2 : 5BA4 21DE
DESTINATION #3 : 5BA4 12ED SOURCE #3 : 5BA4 22DD
DESTINATION #4 : 5BA4 13EC SOURCE #4 : 5BA4 23DC
DESTINATION #5 : 5BA4 14EB SOURCE #5 : 5BA4 24DB
DESTINATION #6 : 5BA4 15EA SOURCE #6 : 5BA4 25DA
DESTINATION #7 : 5BA4 16E9 SOURCE #7 : 5BA4 26D9
DESTINATION #8 : 5BA4 17E8 SOURCE #8 : 5BA4 27D8
DESTINATION #9 : 5BA4 18E7 SOURCE #9 : 5BA4 28D7
DESTINATION #10 : 5BA4 19E6 SOURCE #10 : 5BA4 29D6
DESTINATION #11 : 5BA4 1AE5 SOURCE #11 : 5BA4 2AD5
DESTINATION #12 : 5BA4 1BE4 SOURCE #12 : 5BA4 2BD4
DESTINATION #13 : 5BA4 1CE3 SOURCE #13 : 5BA4 2CD3
DESTINATION #14 : 5BA4 1DE2 SOURCE #14 : 5BA4 2DD2
DESTINATION #15 : 5BA4 1EE1 SOURCE #15 : 5BA4 2ED1
DESTINATION #16 : 5BA4 1FE0 SOURCE #16 : 5BA4 2FD0
For Example:
Let Destination # 1 show the signal from Source #1~4
The IR Data Code list : 5BA4 10EF 5BA4 20DF
Destination # 1 , Source #1 5BA4 10EF 5BA4 21DE
Destination # 1 , Source #2 5BA4 10EF 5BA4 22DD
Destination # 1 , Source #3 5BA4 10EF 5BA4 23DC
Destination # 1 , Source #4 5BA4 14EB 5BA4 24DB

15
REMOTE PROTOCOL COMMANDS
Let Destination # 1 show the signal from Source #1~16 Let Destination # 2 show the signal from Source #1~16 Let Destination # 3 show the signal from Source #1~16
Press Destination# > Source# The IR Data Code list : Press Destination# > Source# The IR Data Code list : Press Destination# > Source# The IR Data Code list :
Destination # 1 Source # 1 5BA4 10EF 5BA4 20DF Destination # 2 Source # 1 5BA4 11EE 5BA4 20DF Destination # 3 Source # 1 5BA4 12ED 5BA4 20DF
Destination # 1 Source # 2 5BA4 10EF 5BA4 21DE Destination # 2 Source # 2 5BA4 11EE 5BA4 21DE Destination # 3 Source # 2 5BA4 12ED 5BA4 21DE
Destination # 1 Source # 3 5BA4 10EF 5BA4 22DD Destination # 2 Source # 3 5BA4 11EE 5BA4 22DD Destination # 3 Source # 3 5BA4 12ED 5BA4 22DD
Destination # 1 Source # 4 5BA4 10EF 5BA4 23DC Destination # 2 Source # 4 5BA4 11EE 5BA4 23DC Destination # 3 Source # 4 5BA4 12ED 5BA4 23DC
Destination # 1 Source # 5 5BA4 10EF 5BA4 24DB Destination # 2 Source # 5 5BA4 11EE 5BA4 24DB Destination # 3 Source # 5 5BA4 12ED 5BA4 24DB
Destination # 1 Source # 6 5BA4 10EF 5BA4 25DA Destination # 2 Source # 6 5BA4 11EE 5BA4 25DA Destination # 3 Source # 6 5BA4 12ED 5BA4 25DA
Destination # 1 Source # 7 5BA4 10EF 5BA4 26D9 Destination # 2 Source # 7 5BA4 11EE 5BA4 26D9 Destination # 3 Source # 7 5BA4 12ED 5BA4 26D9
Destination # 1 Source # 8 5BA4 10EF 5BA4 27D8 Destination # 2 Source # 8 5BA4 11EE 5BA4 27D8 Destination # 3 Source # 8 5BA4 12ED 5BA4 27D8
Destination # 1 Source # 9 5BA4 10EF 5BA4 28D7 Destination # 2 Source # 9 5BA4 11EE 5BA4 28D7 Destination # 3 Source # 9 5BA4 12ED 5BA4 28D7
Destination # 1 Source #10 5BA4 10EF 5BA4 29D6 Destination # 2 Source #10 5BA4 11EE 5BA4 29D6 Destination # 3 Source #10 5BA4 12ED 5BA4 29D6
Destination # 1 Source #11 5BA4 10EF 5BA4 2AD5 Destination # 2 Source #11 5BA4 11EE 5BA4 2AD5 Destination # 3 Source #11 5BA4 12ED 5BA4 2AD5
Destination # 1 Source #12 5BA4 10EF 5BA4 2BD4 Destination # 2 Source #12 5BA4 11EE 5BA4 2BD4 Destination # 3 Source #12 5BA4 12ED 5BA4 2BD4
Destination # 1 Source #13 5BA4 10EF 5BA4 2CD3 Destination # 2 Source #13 5BA4 11EE 5BA4 2CD3 Destination # 3 Source #13 5BA4 12ED 5BA4 2CD3
Destination # 1 Source #14 5BA4 10EF 5BA4 2DD2 Destination # 2 Source #14 5BA4 11EE 5BA4 2DD2 Destination # 3 Source #14 5BA4 12ED 5BA4 2DD2
Destination # 1 Source #15 5BA4 10EF 5BA4 2ED1 Destination # 2 Source #15 5BA4 11EE 5BA4 2ED1 Destination # 3 Source #15 5BA4 12ED 5BA4 2ED1
Destination # 1 Source #16 5BA4 10EF 5BA4 2FD0 Destination # 2 Source #16 5BA4 11EE 5BA4 2FD0 Destination # 3 Source #16 5BA4 12ED 5BA4 2FD0
Let Destination # 4 show the signal from Source #1~16 Let Destination # 5 show the signal from Source #1~16 Let Destination # 6 show the signal from Source #1~16
Press Destination# > Source# The IR Data Code list : Press Destination# > Source# The IR Data Code list : Press Destination# > Source# The IR Data Code list :
Destination # 4 Source # 1 5BA4 13EC 5BA4 20DF Destination # 5 Source # 1 5BA4 14EB 5BA4 20DF Destination # 6 Source # 1 5BA4 15EA 5BA4 20DF
Destination # 4 Source # 2 5BA4 13EC 5BA4 21DE Destination # 5 Source # 2 5BA4 14EB 5BA4 21DE Destination # 6 Source # 2 5BA4 15EA 5BA4 21DE
Destination # 4 Source # 3 5BA4 13EC 5BA4 22DD Destination # 5 Source # 3 5BA4 14EB 5BA4 22DD Destination # 6 Source # 3 5BA4 15EA 5BA4 22DD
Destination # 4 Source # 4 5BA4 13EC 5BA4 23DC Destination # 5 Source # 4 5BA4 14EB 5BA4 23DC Destination # 6 Source # 4 5BA4 15EA 5BA4 23DC
Destination # 4 Source # 5 5BA4 13EC 5BA4 24DB Destination # 5 Source # 5 5BA4 14EB 5BA4 24DB Destination # 6 Source # 5 5BA4 15EA 5BA4 24DB
Destination # 4 Source # 6 5BA4 13EC 5BA4 25DA Destination # 5 Source # 6 5BA4 14EB 5BA4 25DA Destination # 6 Source # 6 5BA4 15EA 5BA4 25DA
Destination # 4 Source # 7 5BA4 13EC 5BA4 26D9 Destination # 5 Source # 7 5BA4 14EB 5BA4 26D9 Destination # 6 Source # 7 5BA4 15EA 5BA4 26D9
Destination # 4 Source # 8 5BA4 13EC 5BA4 27D8 Destination # 5 Source # 8 5BA4 14EB 5BA4 27D8 Destination # 6 Source # 8 5BA4 15EA 5BA4 27D8
Destination # 4 Source # 9 5BA4 13EC 5BA4 28D7 Destination # 5 Source # 9 5BA4 14EB 5BA4 28D7 Destination # 6 Source # 9 5BA4 15EA 5BA4 28D7
Destination # 4 Source #10 5BA4 13EC 5BA4 29D6 Destination # 5 Source #10 5BA4 14EB 5BA4 29D6 Destination # 6 Source #10 5BA4 15EA 5BA4 29D6
Destination # 4 Source #11 5BA4 13EC 5BA4 2AD5 Destination # 5 Source #11 5BA4 14EB 5BA4 2AD5 Destination # 6 Source #11 5BA4 15EA 5BA4 2AD5
Destination # 4 Source #12 5BA4 13EC 5BA4 2BD4 Destination # 5 Source #12 5BA4 14EB 5BA4 2BD4 Destination # 6 Source #12 5BA4 15EA 5BA4 2BD4
Destination # 4 Source #13 5BA4 13EC 5BA4 2CD3 Destination # 5 Source #13 5BA4 14EB 5BA4 2CD3 Destination # 6 Source #13 5BA4 15EA 5BA4 2CD3
Destination # 4 Source #14 5BA4 13EC 5BA4 2DD2 Destination # 5 Source #14 5BA4 14EB 5BA4 2DD2 Destination # 6 Source #14 5BA4 15EA 5BA4 2DD2
Destination # 4 Source #15 5BA4 13EC 5BA4 2ED1 Destination # 5 Source #15 5BA4 14EB 5BA4 2ED1 Destination # 6 Source #15 5BA4 15EA 5BA4 2ED1
Destination # 4 Source #16 5BA4 13EC 5BA4 2FD0 Destination # 5 Source #16 5BA4 14EB 5BA4 2FD0 Destination # 6 Source #16 5BA4 15EA 5BA4 2FD0
Let Destination # 7 show the signal from Source #1~16 Let Destination # 8 show the signal from Source #1~16 Let Destination # 9 show the signal from Source #1~16
Press Destination# > Source# The IR Data Code list : Press Destination# > Source# The IR Data Code list : Press Destination# > Source# The IR Data Code list :
Destination # 7 Source # 1 5BA4 16E9 5BA4 20DF Destination # 8 Source # 1 5BA4 17E8 5BA4 20DF Destination # 9 Source # 1 5BA4 18E7 5BA4 20DF
Destination # 7 Source # 2 5BA4 16E9 5BA4 21DE Destination # 8 Source # 2 5BA4 17E8 5BA4 21DE Destination # 9 Source # 2 5BA4 18E7 5BA4 21DE
Destination # 7 Source # 3 5BA4 16E9 5BA4 22DD Destination # 8 Source # 3 5BA4 17E8 5BA4 22DD Destination # 9 Source # 3 5BA4 18E7 5BA4 22DD
Destination # 7 Source # 4 5BA4 16E9 5BA4 23DC Destination # 8 Source # 4 5BA4 17E8 5BA4 23DC Destination # 9 Source # 4 5BA4 18E7 5BA4 23DC
Destination # 7 Source # 5 5BA4 16E9 5BA4 24DB Destination # 8 Source # 5 5BA4 17E8 5BA4 24DB Destination # 9 Source # 5 5BA4 18E7 5BA4 24DB
Destination # 7 Source # 6 5BA4 16E9 5BA4 25DA Destination # 8 Source # 6 5BA4 17E8 5BA4 25DA Destination # 9 Source # 6 5BA4 18E7 5BA4 25DA
Destination # 7 Source # 7 5BA4 16E9 5BA4 26D9 Destination # 8 Source # 7 5BA4 17E8 5BA4 26D9 Destination # 9 Source # 7 5BA4 18E7 5BA4 26D9
Destination # 7 Source # 8 5BA4 16E9 5BA4 27D8 Destination # 8 Source # 8 5BA4 17E8 5BA4 27D8 Destination # 9 Source # 8 5BA4 18E7 5BA4 27D8
Destination # 7 Source # 9 5BA4 16E9 5BA4 28D7 Destination # 8 Source # 9 5BA4 17E8 5BA4 28D7 Destination # 9 Source # 9 5BA4 18E7 5BA4 28D7
Destination # 7 Source #10 5BA4 16E9 5BA4 29D6 Destination # 8 Source #10 5BA4 17E8 5BA4 29D6 Destination # 9 Source #10 5BA4 18E7 5BA4 29D6
Destination # 7 Source #11 5BA4 16E9 5BA4 2AD5 Destination # 8 Source #11 5BA4 17E8 5BA4 2AD5 Destination # 9 Source #11 5BA4 18E7 5BA4 2AD5
Destination # 7 Source #12 5BA4 16E9 5BA4 2BD4 Destination # 8 Source #12 5BA4 17E8 5BA4 2BD4 Destination # 9 Source #12 5BA4 18E7 5BA4 2BD4
Destination # 7 Source #13 5BA4 16E9 5BA4 2CD3 Destination # 8 Source #13 5BA4 17E8 5BA4 2CD3 Destination # 9 Source #13 5BA4 18E7 5BA4 2CD3
Destination # 7 Source #14 5BA4 16E9 5BA4 2DD2 Destination # 8 Source #14 5BA4 17E8 5BA4 2DD2 Destination # 9 Source #14 5BA4 18E7 5BA4 2DD2
Destination # 7 Source #15 5BA4 16E9 5BA4 2ED1 Destination # 8 Source #15 5BA4 17E8 5BA4 2ED1 Destination # 9 Source #15 5BA4 18E7 5BA4 2ED1
Destination # 7 Source #16 5BA4 16E9 5BA4 2FD0 Destination # 8 Source #16 5BA4 17E8 5BA4 2FD0 Destination # 9 Source #16 5BA4 18E7 5BA4 2FD0

16
REMOTE PROTOCOL COMMANDS
Let Destination # 10 show the signal from Source #1~16 Let Destination # 11 show the signal from Source #1~16 Let Destination # 12 show the signal from Source #1~16
Press Destination# > Source# The IR Data Code list : Press Destination# > Source# The IR Data Code list : Press Destination# > Source# The IR Data Code list :
Destination#10 Source # 1 5BA4 19E6 5BA4 20DF Destination#11 Source # 1 5BA4 1AE5 5BA4 20DF Destination#12 Source # 1 5BA4 1BE4 5BA4 20DF
Destination#10 Source # 2 5BA4 19E6 5BA4 21DE Destination#11 Source # 2 5BA4 1AE5 5BA4 21DE Destination#12 Source # 2 5BA4 1BE4 5BA4 21DE
Destination#10 Source # 3 5BA4 19E6 5BA4 22DD Destination#11 Source # 3 5BA4 1AE5 5BA4 22DD Destination#12 Source # 3 5BA4 1BE4 5BA4 22DD
Destination#10 Source # 4 5BA4 19E6 5BA4 23DC Destination#11 Source # 4 5BA4 1AE5 5BA4 23DC Destination#12 Source # 4 5BA4 1BE4 5BA4 23DC
Destination#10 Source # 5 5BA4 19E6 5BA4 24DB Destination#11 Source # 5 5BA4 1AE5 5BA4 24DB Destination#12 Source # 5 5BA4 1BE4 5BA4 24DB
Destination#10 Source # 6 5BA4 19E6 5BA4 25DA Destination#11 Source # 6 5BA4 1AE5 5BA4 25DA Destination#12 Source # 6 5BA4 1BE4 5BA4 25DA
Destination#10 Source # 7 5BA4 19E6 5BA4 26D9 Destination#11 Source # 7 5BA4 1AE5 5BA4 26D9 Destination#12 Source # 7 5BA4 1BE4 5BA4 26D9
Destination#10 Source # 8 5BA4 19E6 5BA4 27D8 Destination#11 Source # 8 5BA4 1AE5 5BA4 27D8 Destination#12 Source # 8 5BA4 1BE4 5BA4 27D8
Destination#10 Source # 9 5BA4 19E6 5BA4 28D7 Destination#11 Source # 9 5BA4 1AE5 5BA4 28D7 Destination#12 Source # 9 5BA4 1BE4 5BA4 28D7
Destination#10 Source #10 5BA4 19E6 5BA4 29D6 Destination#11 Source #10 5BA4 1AE5 5BA4 29D6 Destination#12 Source #10 5BA4 1BE4 5BA4 29D6
Destination#10 Source #11 5BA4 19E6 5BA4 2AD5 Destination#11 Source #11 5BA4 1AE5 5BA4 2AD5 Destination#12 Source #11 5BA4 1BE4 5BA4 2AD5
Destination#10 Source #12 5BA4 19E6 5BA4 2BD4 Destination#11 Source #12 5BA4 1AE5 5BA4 2BD4 Destination#12 Source #12 5BA4 1BE4 5BA4 2BD4
Destination#10 Source #13 5BA4 19E6 5BA4 2CD3 Destination#11 Source #13 5BA4 1AE5 5BA4 2CD3 Destination#12 Source #13 5BA4 1BE4 5BA4 2CD3
Destination#10 Source #14 5BA4 19E6 5BA4 2DD2 Destination#11 Source #14 5BA4 1AE5 5BA4 2DD2 Destination#12 Source #14 5BA4 1BE4 5BA4 2DD2
Destination#10 Source #15 5BA4 19E6 5BA4 2ED1 Destination#11 Source #15 5BA4 1AE5 5BA4 2ED1 Destination#12 Source #15 5BA4 1BE4 5BA4 2ED1
Destination#10 Source #16 5BA4 19E6 5BA4 2FD0 Destination#11 Source #16 5BA4 1AE5 5BA4 2FD0 Destination#12 Source #16 5BA4 1BE4 5BA4 2FD0
Let Destination # 13 show the signal from Source #1~16 Let Destination # 14 show the signal from Source #1~16 Let Destination # 15 show the signal from Source #1~16
Press Destination# > Source# The IR Data Code list : Press Destination# > Source# The IR Data Code list : Press Destination# > Source# The IR Data Code list :
Destination#13 Source # 1 5BA4 1CE3 5BA4 20DF Destination#14 Source # 1 5BA4 1DE2 5BA4 20DF Destination#15 Source # 1 5BA4 1EE1 5BA4 20DF
Destination#13 Source # 2 5BA4 1CE3 5BA4 21DE Destination#14 Source # 2 5BA4 1DE2 5BA4 21DE Destination#15 Source # 2 5BA4 1EE1 5BA4 21DE
Destination#13 Source # 3 5BA4 1CE3 5BA4 22DD Destination#14 Source # 3 5BA4 1DE2 5BA4 22DD Destination#15 Source # 3 5BA4 1EE1 5BA4 22DD
Destination#13 Source # 4 5BA4 1CE3 5BA4 23DC Destination#14 Source # 4 5BA4 1DE2 5BA4 23DC Destination#15 Source # 4 5BA4 1EE1 5BA4 23DC
Destination#13 Source # 5 5BA4 1CE3 5BA4 24DB Destination#14 Source # 5 5BA4 1DE2 5BA4 24DB Destination#15 Source # 5 5BA4 1EE1 5BA4 24DB
Destination#13 Source # 6 5BA4 1CE3 5BA4 25DA Destination#14 Source # 6 5BA4 1DE2 5BA4 25DA Destination#15 Source # 6 5BA4 1EE1 5BA4 25DA
Destination#13 Source # 7 5BA4 1CE3 5BA4 26D9 Destination#14 Source # 7 5BA4 1DE2 5BA4 26D9 Destination#15 Source # 7 5BA4 1EE1 5BA4 26D9
Destination#13 Source # 8 5BA4 1CE3 5BA4 27D8 Destination#14 Source # 8 5BA4 1DE2 5BA4 27D8 Destination#15 Source # 8 5BA4 1EE1 5BA4 27D8
Destination#13 Source # 9 5BA4 1CE3 5BA4 28D7 Destination#14 Source # 9 5BA4 1DE2 5BA4 28D7 Destination#15 Source # 9 5BA4 1EE1 5BA4 28D7
Destination#13 Source #10 5BA4 1CE3 5BA4 29D6 Destination#14 Source #10 5BA4 1DE2 5BA4 29D6 Destination#15 Source #10 5BA4 1EE1 5BA4 29D6
Destination#13 Source #11 5BA4 1CE3 5BA4 2AD5 Destination#14 Source #11 5BA4 1DE2 5BA4 2AD5 Destination#15 Source #11 5BA4 1EE1 5BA4 2AD5
Destination#13 Source #12 5BA4 1CE3 5BA4 2BD4 Destination#14 Source #12 5BA4 1DE2 5BA4 2BD4 Destination#15 Source #12 5BA4 1EE1 5BA4 2BD4
Destination#13 Source #13 5BA4 1CE3 5BA4 2CD3 Destination#14 Source #13 5BA4 1DE2 5BA4 2CD3 Destination#15 Source #13 5BA4 1EE1 5BA4 2CD3
Destination#13 Source #14 5BA4 1CE3 5BA4 2DD2 Destination#14 Source #14 5BA4 1DE2 5BA4 2DD2 Destination#15 Source #14 5BA4 1EE1 5BA4 2DD2
Destination#13 Source #15 5BA4 1CE3 5BA4 2ED1 Destination#14 Source #15 5BA4 1DE2 5BA4 2ED1 Destination#15 Source #15 5BA4 1EE1 5BA4 2ED1
Destination#13 Source #16 5BA4 1CE3 5BA4 2FD0 Destination#14 Source #16 5BA4 1DE2 5BA4 2FD0 Destination#15 Source #16 5BA4 1EE1 5BA4 2FD0
Let Destination # 16 show the signal from Source #1~16
Press Destination# > Source# The IR Data Code list :
Destination#16 Source # 1 5BA4 1FE0 5BA4 20DF
Destination#16 Source # 2 5BA4 1FE0 5BA4 21DE
Destination#16 Source # 3 5BA4 1FE0 5BA4 22DD
Destination#16 Source # 4 5BA4 1FE0 5BA4 23DC
Destination#16 Source # 5 5BA4 1FE0 5BA4 24DB
Destination#16 Source # 6 5BA4 1FE0 5BA4 25DA
Destination#16 Source # 7 5BA4 1FE0 5BA4 26D9
Destination#16 Source # 8 5BA4 1FE0 5BA4 27D8
Destination#16 Source # 9 5BA4 1FE0 5BA4 28D7
Destination#16 Source #10 5BA4 1FE0 5BA4 29D6
Destination#16 Source #11 5BA4 1FE0 5BA4 2AD5
Destination#16 Source #12 5BA4 1FE0 5BA4 2BD4
Destination#16 Source #13 5BA4 1FE0 5BA4 2CD3
Destination#16 Source #14 5BA4 1FE0 5BA4 2DD2
Destination#16 Source #15 5BA4 1FE0 5BA4 2ED1
Destination#16 Source #16 5BA4 1FE0 5BA4 2FD0

17
REMOTE CONTROL
ROOM IR REMOTE CONTROL #01 ~ #09 CUSTOM CODE AND DATA CODES
IR CUSTOM AND DATA CODES (NEC Standard)
PRESS Number To Select SOURCE
CUSTOM CODE: 42BD
IR-01 DATA CODE:
SOURCE #1 : 42BD 00FF
SOURCE #2 : 42BD 01FE
SOURCE #3 : 42BD 02FD
SOURCE #4 : 42BD 03FC
SOURCE #5 : 42BD 04FB
SOURCE #6 : 42BD 05FA
SOURCE #7 : 42BD 06F9
SOURCE #8 : 42BD 07F8
SOURCE #9 : 42BD 08F7
SOURCE #10 : 42BD 09F6
SOURCE #11 : 42BD 0AF5
SOURCE #12 : 42BD 0BF4
SOURCE #13 : 42BD 0CF3
SOURCE #14 : 42BD 0DF2
SOURCE #15 : 42BD 0EF1
SOURCE #16 : 42BD 0FF0
IR-02 DATA CODE:
SOURCE #1 : 42BD 10EF
SOURCE #2 : 42BD 11EE
SOURCE #3 : 42BD 12ED
SOURCE #4 : 42BD 13EC
SOURCE #5 : 42BD 14EB
SOURCE #6 : 42BD 15EA
SOURCE #7 : 42BD 16E9
SOURCE #8 : 42BD 17E8
SOURCE #9 : 42BD 18E7
SOURCE #10 : 42BD 19E6
SOURCE #11 : 42BD 1AE5
SOURCE #12 : 42BD 1BE4
SOURCE #13 : 42BD 1CE3
SOURCE #14 : 42BD 1DE2
SOURCE #15 : 42BD 1EE1
SOURCE #16 : 42BD 1FE0
IR-03 DATA CODE:
SOURCE #1 : 42BD 20DF
SOURCE #2 : 42BD 21DE
SOURCE #3 : 42BD 22DD
SOURCE #4 : 42BD 23DC
SOURCE #5 : 42BD 24DB
SOURCE #6 : 42BD 25DA
SOURCE #7 : 42BD 26D9
SOURCE #8 : 42BD 27D8
SOURCE #9 : 42BD 28D7
SOURCE #10 : 42BD 29D6
SOURCE #11 : 42BD 2AD5
SOURCE #12 : 42BD 2BD4
SOURCE #13 : 42BD 2CD3
SOURCE #14 : 42BD 2DD2
SOURCE #15 : 42BD 2ED1
SOURCE #16 : 42BD 2FD0
IR-04 DATA CODE:
SOURCE #1 : 42BD 30CF
SOURCE #2 : 42BD 31CE
SOURCE #3 : 42BD 32CD
SOURCE #4 : 42BD 33CC
SOURCE #5 : 42BD 34CB
SOURCE #6 : 42BD 35CA
SOURCE #7 : 42BD 36C9
SOURCE #8 : 42BD 37C8
SOURCE #9 : 42BD 38C7
SOURCE #10 : 42BD 39C6
SOURCE #11 : 42BD 3AC5
SOURCE #12 : 42BD 3BC4
SOURCE #13 : 42BD 3CC3
SOURCE #14 : 42BD 3DC2
SOURCE #15 : 42BD 3EC1
SOURCE #16 : 42BD 3FC0
IR-05 DATA CODE:
SOURCE #1 : 42BD 40BF
SOURCE #2 : 42BD 41BE
SOURCE #3 : 42BD 42BD
SOURCE #4 : 42BD 43BC
SOURCE #5 : 42BD 44BB
SOURCE #6 : 42BD 45BA
SOURCE #7 : 42BD 46B9
SOURCE #8 : 42BD 47B8
SOURCE #9 : 42BD 48B7
SOURCE #10 : 42BD 49B6
SOURCE #11 : 42BD 4AB5
SOURCE #12 : 42BD 4BB4
SOURCE #13 : 42BD 4CB3
SOURCE #14 : 42BD 4DB2
SOURCE #15 : 42BD 4EB1
SOURCE #16 : 42BD 4FB0
IR-06 DATA CODE:
SOURCE #1 : 42BD 50AF
SOURCE #2 : 42BD 51AE
SOURCE #3 : 42BD 52AD
SOURCE #4 : 42BD 53AC
SOURCE #5 : 42BD 54AB
SOURCE #6 : 42BD 55AA
SOURCE #7 : 42BD 56A9
SOURCE #8 : 42BD 57A8
SOURCE #9 : 42BD 58A7
SOURCE #10 : 42BD 59A6
SOURCE #11 : 42BD 5AA5
SOURCE #12 : 42BD 5BA4
SOURCE #13 : 42BD 5CA3
SOURCE #14 : 42BD 5DA2
SOURCE #15 : 42BD 5EA1
SOURCE #16 : 42BD 5FA0
IR-07 DATA CODE:
SOURCE #1 : 42BD 609F
SOURCE #2 : 42BD 619E
SOURCE #3 : 42BD 629D
SOURCE #4 : 42BD 639C
SOURCE #5 : 42BD 649B
SOURCE #6 : 42BD 659A
SOURCE #7 : 42BD 6699
SOURCE #8 : 42BD 6798
SOURCE #9 : 42BD 6897
SOURCE #10 : 42BD 6996
SOURCE #11 : 42BD 6A95
SOURCE #12 : 42BD 6B94
SOURCE #13 : 42BD 6C93
SOURCE #14 : 42BD 6D92
SOURCE #15 : 42BD 6E91
SOURCE #16 : 42BD 6F90
IR-08 DATA CODE:
SOURCE #1 : 42BD 708F
SOURCE #2 : 42BD 718E
SOURCE #3 : 42BD 728D
SOURCE #4 : 42BD 738C
SOURCE #5 : 42BD 748B
SOURCE #6 : 42BD 758A
SOURCE #7 : 42BD 7689
SOURCE #8 : 42BD 7788
SOURCE #9 : 42BD 7887
SOURCE #10 : 42BD 7986
SOURCE #11 : 42BD 7A85
SOURCE #12 : 42BD 7B84
SOURCE #13 : 42BD 7C83
SOURCE #14 : 42BD 7D82
SOURCE #15 : 42BD 7E81
SOURCE #16 : 42BD 7F80
IR-09 DATA CODE:
SOURCE #1 : 42BD 807F
SOURCE #2 : 42BD 817E
SOURCE #3 : 42BD 827D
SOURCE #4 : 42BD 837C
SOURCE #5 : 42BD 847B
SOURCE #6 : 42BD 857A
SOURCE #7 : 42BD 8679
SOURCE #8 : 42BD 8778
SOURCE #9 : 42BD 8877
SOURCE #10 : 42BD 8976
SOURCE #11 : 42BD 8A75
SOURCE #12 : 42BD 8B74
SOURCE #13 : 42BD 8C73
SOURCE #14 : 42BD 8D72
SOURCE #15 : 42BD 8E71
SOURCE #16 : 42BD 8F70

18
REMOTE CONTROL
ROOM IR REMOTE CONTROL #10 ~ #16 CUSTOM CODE AND DATA CODES
IR CUSTOM AND DATA CODES (NEC Standard)
PRESS Number To Select SOURCE
CUSTOM CODE: 42BD
IR-10 DATA CODE:
SOURCE #1 : 42BD 906F
SOURCE #2 : 42BD 916E
SOURCE #3 : 42BD 926D
SOURCE #4 : 42BD 936C
SOURCE #5 : 42BD 946B
SOURCE #6 : 42BD 956A
SOURCE #7 : 42BD 9669
SOURCE #8 : 42BD 9768
SOURCE #9 : 42BD 9867
SOURCE #10 : 42BD 9966
SOURCE #11 : 42BD 9A65
SOURCE #12 : 42BD 9B64
SOURCE #13 : 42BD 9C63
SOURCE #14 : 42BD 9D62
SOURCE #15 : 42BD 9E61
SOURCE #16 : 42BD 9F60
IR-11 DATA CODE:
SOURCE #1 : 42BD A05F
SOURCE #2 : 42BD A15E
SOURCE #3 : 42BD A25D
SOURCE #4 : 42BD A35C
SOURCE #5 : 42BD A45B
SOURCE #6 : 42BD A55A
SOURCE #7 : 42BD A659
SOURCE #8 : 42BD A758
SOURCE #9 : 42BD A857
SOURCE #10 : 42BD A956
SOURCE #11 : 42BD AA55
SOURCE #12 : 42BD AB54
SOURCE #13 : 42BD AC53
SOURCE #14 : 42BD AD52
SOURCE #15 : 42BD AE51
SOURCE #16 : 42BD AF50
IR-12 DATA CODE:
SOURCE #1 : 42BD B04F
SOURCE #2 : 42BD B14E
SOURCE #3 : 42BD B24D
SOURCE #4 : 42BD B34C
SOURCE #5 : 42BD B44B
SOURCE #6 : 42BD B54A
SOURCE #7 : 42BD B649
SOURCE #8 : 42BD B748
SOURCE #9 : 42BD B847
SOURCE #10 : 42BD B946
SOURCE #11 : 42BD BA45
SOURCE #12 : 42BD BB44
SOURCE #13 : 42BD BC43
SOURCE #14 : 42BD BD42
SOURCE #15 : 42BD BE41
SOURCE #16 : 42BD BF40
IR-13 DATA CODE:
SOURCE #1 : 42BD C03F
SOURCE #2 : 42BD C13E
SOURCE #3 : 42BD C23D
SOURCE #4 : 42BD C33C
SOURCE #5 : 42BD C43B
SOURCE #6 : 42BD C53A
SOURCE #7 : 42BD C639
SOURCE #8 : 42BD C738
SOURCE #9 : 42BD C837
SOURCE #10 : 42BD C936
SOURCE #11 : 42BD CA35
SOURCE #12 : 42BD CB34
SOURCE #13 : 42BD CC33
SOURCE #14 : 42BD CD32
SOURCE #15 : 42BD CE31
SOURCE #16 : 42BD CF30
IR-14 DATA CODE:
SOURCE #1 : 42BD D02F
SOURCE #2 : 42BD D12E
SOURCE #3 : 42BD D22D
SOURCE #4 : 42BD D32C
SOURCE #5 : 42BD D42B
SOURCE #6 : 42BD D52A
SOURCE #7 : 42BD D629
SOURCE #8 : 42BD D728
SOURCE #9 : 42BD D827
SOURCE #10 : 42BD D926
SOURCE #11 : 42BD DA25
SOURCE #12 : 42BD DB24
SOURCE #13 : 42BD DC23
SOURCE #14 : 42BD DD22
SOURCE #15 : 42BD DE21
SOURCE #16 : 42BD DF20
IR-15 DATA CODE:
SOURCE #1 : 42BD E01F
SOURCE #2 : 42BD E11E
SOURCE #3 : 42BD E21D
SOURCE #4 : 42BD E31C
SOURCE #5 : 42BD E41B
SOURCE #6 : 42BD E51A
SOURCE #7 : 42BD E619
SOURCE #8 : 42BD E718
SOURCE #9 : 42BD E817
SOURCE #10 : 42BD E916
SOURCE #11 : 42BD EA15
SOURCE #12 : 42BD EB14
SOURCE #13 : 42BD EC13
SOURCE #14 : 42BD ED12
SOURCE #15 : 42BD EE11
SOURCE #16 : 42BD EF10
IR-16 DATA CODE:
SOURCE #1 : 42BD F00F
SOURCE #2 : 42BD F10E
SOURCE #3 : 42BD F20D
SOURCE #4 : 42BD F30C
SOURCE #5 : 42BD F40B
SOURCE #6 : 42BD F50A
SOURCE #7 : 42BD F609
SOURCE #8 : 42BD F708
SOURCE #9 : 42BD F807
SOURCE #10 : 42BD F906
SOURCE #11 : 42BD FA05
SOURCE #12 : 42BD FB04
SOURCE #13 : 42BD FC03
SOURCE #14 : 42BD FD02
SOURCE #15 : 42BD FE01
SOURCE #16 : 42BD FF00