resi-linx digi-MOD RL-DM1102 Instructions for use

SETTINGS DEFAULT SETTINGS OPTIONAL SETTINGS
Channel Output 21 UHF / S31 UHF 6-69 / E2 - E69
FEC (forward error correction) 3/4 1/2, 2/3, 3/4, 5/6, 7/8
Guard Int 1/16 1/2, 1/4, 1/8, 1/16, 1/32
Attenuator 0 0-20dB
Constellation 64QAM 16QAM
OFDM Mode 8K 2K
RF Output Normal Inverted, C.W
Video Input PAL NTSC
Brightness 128 0-256
Contrast 128 0-256
Saturation 128 0-256
Sharpness 64 0-128
Hue 128 0-256
Cell ID 0 adjustable
Stream ID 1000 adjustable
Network ID 100 adjustable
ORG Net ID 10 adjustable
Network Name rl-network adjustable
Program Number 100 adjustable
Channel Name CHANNEL-1 adjustable
LCN 101 adjustable
Aspect Ratio 4:3 16:9
LCN Mode APN EACEM, ITC, NorDig
www.resi-linx.com
digi-MOD RL-DM1102
Radio Frequency Range
Single Input SD Digital Modulator
®
WARRANTY
Vcomm Pty Ltd states that the warrant that the customer can rely on is that provided by the
manufacturer. In the event of any warranty claim please contact us and we will forward it to the
manufacturer. The manufacturer will then determine the extent of their liability. This expressly
negates, to the extent possible by Australian law, any warranty reliance on Vcomm Pty Ltd.
N15275
Technical Specications
MODULATION GENERAL
Video Resolution PAL 720x576 @25fps Power Supply 12 VDC 1.5 AMP
Video Compression MPEG2 MP@ML Consumption 500 MA
Audio Compression MPEG1 Layer ll Dimensions 235 x 145 x 35mm
Weight .955kg
digi-MOD
RL-DM1102
Reset
LCD Display
Scroll Up / Down
Enter Button (OK)
ON
OFF
ANT IN
1 2 3 4
5 6 7 8
INPUT
TV OUTPUTS
AUX MOD RF IN
MOD RF IN
(PWR/IR PASS)
IR
IR LED
PWR LED 12V DC
GAIN
FM TRAP
®
N15275
PATENTED
RL-RF380
12V DC 1.5A
AV SOURCE x 1
12V DC Power Input
Component Video Input
Composite (CVBS)
S-Video Input
RF Output
Gain Control
Remote Power Switch
IR Port
Remote Set-up Indicator
INPUT OUTPUT
Video Input CVBS Output Level 85 dB V
Video Input Level 0.7-1.4 V (pp) Output Impedance 75
Video Mode PAL / NTSC Channel Bandwidth 7 MHz / 8 MHz
Audio Input Stereo Output Level Adjustment 20 dB typ.
Audio Input Level 0.4 - 4.8 V (pp) MER >32 dB typ.
Input Connectors Video (RCA/ S-Video) -Audio (RCA) Connector Type “F” Female
Input Impedance 75
Ʊ
Ʊ
A B C D
EF
A
B
C
D
G
E
F
G
L
K
J
H
M H IJ K
L
M
I
Full Installation manual available @ resi-linx.com
RL-IR700
QUICK INSTALL MANUAL

NOTE: If the digi-MOD is powered down, there is no need to recongure. All settings will remain
unless a factory default is done.
1. Power Up the RL-DM1102
2. Enter Password “0000” and press “OK”
3. Wait until digi-MOD reads “Running” then enter the menu by selecting the “OK” button
4. The LCD screen will now display “ADVANCED MENU OUTPUT CHANNEL” - select the “OK” button
5. The LCD screen will now display “OUTPUT CHANNEL 21” with the frequency in MHz. In some TV
sets Channel 21 is not available, so it is recommended to change this to appropriate available output
channel to suit your installation (40, 50, 60 etc.) Once you have scrolled and selected a channel
number, Select “OK” to lock in the change
6. Change any other settings via the “MENU” as required (refer to full installation manual @ resi-linx.
com)
7. Once nished programming use the “UP” scroll button until the LCD display reads “ADVANCED MENU
EXIT”, select “OK”
8. The LCD will now read “EXIT, EXIT MENU”. Select “OK”. The LCD display will now show “Running”
9. Auto Scan for Channels on the TV set with the digi-MOD connected and powered
10. Sources for selected digi-MOD Channel selection, (e.g channel 40), are found on TV channels 101
(adjustable - refer to Programming LCN)
Initial Startup
Programming
Installing multiple digi-MOD’s in an installation
Please ensure each digi-MOD has different settings in the categories below if you are installing 2 or more
in an installation.
OUTPUT CHANNEL
STREAM (TS) ID
CHANNEL NAME
LCN
NOTE: Failure to change the above settings will result in conict and will not install all channels
correctly.
For web management/programming of the RL-DM1102, please refer to full installation manual
@ resi-linx.com.
CHANNEL NAME can be changed by using the Scroll “UP” key until you reach “CHANNEL NAME”. Use
the UP/DOWN scroll keys to change each letter. Click “OK” to conrm channel name change.
LCN (Logic Channel Number) can be moved from its default position (101, 102, 103 and 104) to a different
channel number (e.g. 4, 5, 6, 8) by scrolling UP/DOWN in the LCN option for each channel. Once selected,
press the “OK” button to lock your channel change.
For more programming option, please refer to the full installation manual @ resi-linx.com.
1. Connect the required AV cable (Component , Composition or S-Video ) from the video source
(eg: Cabel TV, Pay TV, DVD. VCR, Camera) to the appropriate connection on the rear of the RL-
DM1102 Modulator
2. Video Input is defaulted for composite video (CVBS). For component and S-Video sources, change
Video Input via “Encoder Setup/Video Input”. Once selected press OK to save
3. Connect the RCA cable from the audio source to the red/white Audio Input (Audio L & R) on the rear
of the RL-DM1102 Modulator
4. Connect the RF Output from the RL-DM1102 to the Modulator Input on the RF Distribution Module
RL-RF380. Alternatively connect the RF Output to an existing distribution system or directly to a
television set
5. Connect the supplied 12V DC Switch Mode Power Supply to the Power Input
6. Connect IR emitters RL-IR700/800 to the IR output on the rear of the RL-DM1102 Modulator. Place
the other end of the emitter on your AV device near the IR pick up
NOTE: When Remote Power Switch is ON - the RL-RF380 should not have a Power Supply connected
Hardware Connection
Safety Precautions
• Do not apply power to the DVB-T Digital Modulator until all components have been installed and all wiring has been
properly terminated. Failure to do so may result in damage to the product and void manufacturer’s warranty.
• Do not attempt to terminate, change or un-install any wiring without rst unplugging Power Adapter from the DVB-T
Digital IR Modulator.
• Do not expose any component to moisture. Doing so can create electrical hazards or render the component
unusable. Exposure to moisture will also void the warranty on the system.
• This modulator is powered with a voltage of 12 VDC. The power supply voltage must not exceed this, otherwise this
modulator could suffer irreparable damage and subsequent invalidation of the warranty.
Note:
- Do not replace the power supply with a voltage greater than 12 VDC.
- Do not connect the modulator to the power if the power cord is damaged.
- Do not plug the modulator into the mains supply until all cables have been connected correctly.
- Do not cut the cord.
• Avoid placing the modulator next to central heating components and in areas of high humidity.
• Do not cover any modulator elements that could obstruct the ventilation slots and cause overheating.
• If the modulator has been kept in cold conditions for a long time, keep it in a warm room no less than 2 hours before
plugging it into the mains.
• Do not place digi-MOD on top or underneath a PVR Device, as this could cause overheating.
FG H
G
E
L
K
I