Resolution RE208 User manual

RE208_Hardwire_to_Honeywell-Compat_Translator
Page 1 of 4 24-Hour Tech Support Line: [phone] 30-Oct-14
www.ResolutionProducts.com
RE208 Hardwire-to-Honeywell
®
or 2GIG
®
Wireless Translator™
Features
• Converts hardwire zones into Honeywell-compatible wireless signals.
• 8 Hardwire loops with end-of-line resistor detection.
• Uni ue wireless ID for each zone, plus 1 for main device.
• Transmit diversity for long reliable range.
• PIR powering (via external supply).
• 3 year operation on batteries (contacts only).
• Complete supervision of zone tampers and low battery.
Key Instructions
• DO NOT MOUNT IN A METAL CAN.
• DO NOT PUT POWER ON HARDWIRE TERMINALS.
• Use with normally closed contacts in-line with 4.7 K-ohms resistors (mandatory).
• Not for use with life safety devices, such as Smoke or CO sensors.
• External supply re uirements:
 Contacts-only installations may use wall plug power supply (see specifications)
 Installations with PIRs or Glassbreaks (powered devices) re uire battery-backed
external power supply (see diagram).
 Without backed-up power, PIRs or Glass Breaks could alarm when
power is lost.
 Translator AA batteries drive contacts only, and do not drive powered
devices.
 Ensure that external supply has sufficient current to supply all
powered devices including Translator.
 4-wire powered devices only. Not for use with 2-wire powered
devices.
 If using old panel as the battery-backed 12V DC supply, verify supply
and battery operation. DO NOT MOUNT IN OLD CAN… the wireless will
not get out!
Installation
• Hook up PIR and Glass Break power lines to external power supply.
• Alarm contact hook-up:
 Works only with normally-closed contacts alarm = open).
 Remove any existing end-of-line resistors.
 Connect 4.7K end-of-line resistor included) IN-LINE with contact .
 Resistor should NOT be across between) terminals .
Honeywell® Enrollment
Sensors:
RF Learning tripping enrollment mode.
Set up for any behavior desired.
Input Type: 3 (Supervised RF
When prompted, open/close each zone
twice to enroll serial number.
Ensure it is set to Loop: 2.
Translator itself:
RF Learning tripping enrollment mode.
Zone Type: 8 (24 hour Aux
Input Type: 3 (Supervised RF ,
When prompted, toggle the tamper
switch to enroll serial number.
Loop 2 (but Loop doesn’t really
matter .
2GIG® Enrollment:
Sensors:
Q1 RF Sensor
Set up for any behavior desired.
At “Enter RF Serial Number”, press SHIFT LEARN, and trip sensor.
Ensure it is set to Loop 2.
Translator itself:
Sensor Type: (08 24 Hour Aux
Equipment Type: (1 contact
Equipment Code: (0000 other
Other Equipment Code: (208 meaning RE208
Enter RF Serial Number: [press SHIFT,Learn, then toggle the tamper
switch to enroll the serial number]
Equipment Age: (0 new
Loop Number: (2 but Loop doesn’t really matter
Dialer Delay: (1 enabled
RE208_Hardwire_to_Honeywell-Compat_Translator
Page 2 of 4 24-Hour Tech Support Line: [phone] 30-Oct-14
www.ResolutionProducts.com
• Application Diagram
• Connection Diagram
4.7K
Contact
(Normally Closed)
Loop
x
PIR
To Enroll zone,
Open and close contact.
This sends a open/close
signal to panel.
Translator
Batteries DO NOT
power external
devices
Altronix AL100UL
12VDC Supply
With Lead-acid
battery
Old Panel ay be used,
if operation fully verified
+12 VDC GND
PIR
Power
Input
PIR Contact
Output
(Nor ally
Closed)
4.7K
Loop
y
Altronix TP1620
16.5VAC, 20VA
Transformer
with securing screw
Resolution
RE012
12 VDC
Powe r Supply
NON-Switched
Outlet
Use Battery-Backed 12VDC
if powering
PIRs or Glass Breaks
Use Non-Battery-Backed
Supply ONLY if installation is
all non-powered contacts
Power Supply polarity
DOES NOT matter!
End of Line
Resistor
New Wireless
System
Existing Hardwire Sensors
New Honeywell
Self-Contained System in
living area
Taking over old Hardwire anel,
usually mounted in utility area
Honeywell Wireless
May use GE 60
-
898
-
ITI supply here,
if securing screw is desired

RE208_Hardwire_to_Honeywell-Compat_Translator
Page 3 of 4 24-Hour Tech Support Line: [phone] 30-Oct-14
www.ResolutionProducts.com
Operation
• 8 Hardwire 4.7K-ohm Zones – transmit 8 uni ue wireless IDs:
Alarm, when device sees open circuit.
Tamper, when device sees short circuit.
Supervisories, every hour for each zone.
• Translator Main Zone wireless transmission (9
th
uni ue ID):
Tamper, when cover opened.
Low battery, when either low AA batteries, OR loss of 12V DC external.
Supervisory every hour.
• LED Operation
Green LED: On if AC power present.
Red LED: When 12V DC is present: “Blinks” on transmit to panel;
“on” if device tamper or device low battery.
Specifications
Honeywell Loop: Loop 2 for zones 1-8, Loop 4 for Translator tamper.
Zone sensing duration: State sensed if held more than 600ms.
End-of-line Resistors: 4.7k-ohm, 5%.
Max wire run: 1000 feet.
Backup batteries: Two AA Alkaline.
External supply: 8.5 to 13 VDC or 6-9 VAC
Standard: Resolution RE012: 12VDC, 50mA.
Optional: GE 60-898-ITI, for securing screw
Wire connection polarity DOESN’T matter!
Current draw with supply: 4mA, normal operation.
PIR usage: PIR may need tight voltage tolerance. Add PIR and
device current re uirements together to get total
current need.
AC Fail Indication: Translator ID sends Low Battery signal if its external 12V
is gone for 15 minutes. Restores on external 12V
restore.
AA Low Battery Conditions: Low battery for 1 minute. Restores on device
tamper, external 12V restore.
AA Battery Life on AC Fail: 3-5 years, when monitoring contacts.
Housing dimensions: 4x6x1 inches
Specifications subject to change without notice.
Internal Picture
Terminals for Zones 1, 2
Terminals for Zones 4-8
Power Terminals
Tamper / Enroll Switch
Terminals for Zone 3
RE208_Hardwire_to_Honeywell-Compat_Translator
Page 4 of 4 24-Hour Tech Support Line: [phone] 30-Oct-14
www.ResolutionProducts.com
Notices
“GE”, “Honeywell”, “DSC”, “2GIG” and “Napco” are trademarks owned by General Electric Company,
Honeywell International Inc., Tyco Safety Products Canada LTD, 2GIG Technologies Inc., and NAPCO
Security Systems, Inc., respectively.
Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or Napco systems.
However, no Resolution product is produced by, endorsed by, nor is officially associated with GE,
Honeywell, DSC or Napco. Resolution recommends verifying proper enrollment and operation, per control
panel installation instructions, at installation.
Do not use Translator for life safety devices, such as smoke or CO sensors.
Warranty
Resolution Products, Inc. will replace products that are defective in their first five (5 years.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference that may be received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Products, Inc. could void the
user's authority to operate this equipment.
FCC ID: U5X-RE208
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s . Operation is
subject to the following two conditions:
(1 This device may not cause interference, and
(2 This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1 l'appareil ne doit pas produire de brouillage, et
(2 l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
IC: 8310A-RE208