Resolution RE324TD User manual

RE324TD_2GIG-to-DSC_Wireless_Translator
Page 1 of 4 24-Hour Tech Support Line: [phone] 16-Oct-14
www.ResolutionProducts.com
RE324TD 2GIG
®
-to-DSC
®
Wireless Translator™
Features
• Listens to 2GIG (& Honeywell) protocol wireless devices.
• Transmits D C protocol wireless.
• Enrolls up to 63 devices.
• Unique wireless E N for each zone, plus 1 for main device.
• All sensor alarm, supervisory and trouble signals are passed through.
• Dual antennas for both Receive and Transmit diversity for reliable range.
• Back-up battery operation.
• Loss of AC/DC power indicator, Translator will beep once a minute.
• Complete supervision of tampers, external power supply fault and low
battery.
Key Instructions
• Translator is for use only with D C systems that have “Easy Wireless
Enrollment”. These include Alexor, Impassa and Version 4.6 Power eries.
• External supply: 12V DC at least 50 mA. NON- WITCHED outlet.
Wire polarity DOE NOT matter!
• Mount Translator at least 20 feet from Control Panel’s receiver.
• 3 AAA Alkaline batteries give 72 hours backup if external supply fails.
IN TALL BATTERIE ONLY WHEN EXTERNAL UPPLY I READY TO CONNECT.
• Enrolling:
 ensor enrollment:
1. Enter Wireless Enrollment Mode on D C Panel.
2. Press Translator Enroll switch repeatedly until Device Type LED
matches the type of device you’re enrolling.
ENROLL PIRs FIR T TO AVOID MI TAKEN ENROLLMENT .
ENROLLING A WRONG DEVICE TYPE CAN CAU E IMPROPER
OPERATION.
3. Activate particular 2GIG (or Honeywell) wireless device:
o PIR: Tamper – ENROLL PIRs FIR T (Used for PIRs and Glass
Break ensors)
o Panic: Button
o Key Fob: Lower Right button
o DW : Tamper NOTE: 2GIG sensors can use magnetic OR
external, but not both. Honeywell 5800 Micra, 5811 Micro,
5814 Micro, 5818 Recessed, 5820L are enrolled by battery
plunge.
Automatic Translator responses:
o Green LED blinks when hearing a 2GIG packet.
o Translator beeps on each enrollment into itself.
o Red LED blinks when speaking a D C packet.
4. Confirm E N, Enter Zone # and Zone Type on D C panel.
 Main Translator device enrolled into panel by its tamper switch.
Zone Type 03 will monitor Tamper, Low Battery and upervisions.
• Deleting sensors enrolled in Translator:
 Delete all sensors:
1. Press enroll button repeatedly until all Device Type LEDs are off.
2. Press and hold enroll key for 5 seconds until beep.
 Delete one Device Type:
1. Press enroll button repeatedly until target Device Type LED is lit.
2. Press and hold enroll key for 5 seconds until beep.
RE324TD_2GIG-to-DSC_Wireless_Translator
Page 2 of 4 24-Hour Tech Support Line: [phone] 16-Oct-14
www.ResolutionProducts.com
Operation
• Existing 2GIG & Honeywell protocol sensors transmit as usual. Translator
passes information on to control panel as if they were D C transmitters.
• Here is the Fob behavior…
2GIG Fob
Buttons
HNW Fob
Buttons … do these actions on the DSC system
Unlock OFF
Off
Away ON
Away
Stay Left
Home
Away+Disarm
Right
Panic
Star
no action
• Translator Module Zone wireless transmission ( unique ID):
Tamper, when cover opened. Also sends restore.
Low battery, when low battery. Also sends restore.
upervisory every hour. upervisory stopped if 12V DC power absent.
Translator Module does not send any alarm signals about itself.
• LED Operation
 Green LED
• On if 12V DC power present.
• Blinks on receipt of 2GIG-compatible packets.
 Red LED
• On if device low battery (unless there’s no 12V DC
power).
• Blinks on transmit of D C-compatible packets.
• Application Diagram
New DSC
Wireless System
New D
SC
Wireless
Sensors
Existing 2GIG
Wireless
Sensors
Existing
Honeywell
Wireless
Sensors

RE324TD_2GIG-to-DSC_Wireless_Translator
Page 3 of 4 24-Hour Tech Support Line: [phone] 16-Oct-14
www.ResolutionProducts.com
Specifications
Backup batteries: Three AAA Alkaline.
External supply: 8.5 to 13 VDC or 6-9 VAC
tandard: Resolution RE012: 12VDC, 50mA.
Optional: GE 60-898-ITI, for securing screw
Wire connection polarity DOE N’T matter!
Current draw with supply: 4mA, normal operation.
Power Fail Conditions: 12V DC gone. Translator device ID supervisories
(including low battery reports) are stopped
during 12V DC loss.
Back-up Battery Life on External upply Fail: 72 hours (cumulative).
Device Low Battery: When approximately 48 hours remain in back-up.
Housing dimensions: 4x6x1 inches
pecifications subject to change without notice.
Internal Picture
Device Type select switch
Power Terminals
POLARITY
DOE N’T MATTER
Tamper witch & spring
Device Type Indicator LEDs
Battery bucket for 3 AAAs
Indicator LEDs & buzzer
2 Antennas for:
Dual Diversity Receive and
Dual Diversity Transmit
Note: Antennas mounted
on outer terminals
RE324TD_2GIG-to-DSC_Wireless_Translator
Page 4 of 4 24-Hour Tech Support Line: [phone] 16-Oct-14
www.ResolutionProducts.com
Notices
GE”, Honeywell”, and DSC” are trademarks owned by General Electric Company, Honeywell
International Inc., and Tyco Safety Products Canada LTD, respectively.
Resolution Products, Inc. products will function with one of either GE, DSC or Honeywell systems.
However, no Resolution product is produced by, endorsed by, nor is officially associated with GE,
Honeywell or DSC. Resolution recommends verifying operation at installation.
Do not use Translator for life safety devices, such as smoke or CO sensors.
Patent 8,456,278
Warranty
Resolution Products, Inc. will replace products that are defective in their first five (5) years.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference that may be received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Products, Inc. could void
the user's authority to operate this equipment.
FCC ID: U5X-RE324
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
IC: 8310A-RE324
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen that the equivalent isotropically radiated po er (e.i.r.p.) is not more
than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne
d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les
risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de
sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement
d'une communication satisfaisante.
This radio transmitter (identify the device by certification number, or model number if Category II) has been approved
by Industry Canada to operate ith the antenna types listed belo ith the maximum permissible gain and required
antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly prohibited for use ith this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait
partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne
énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types
d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits
pour l'exploitation de l'émetteur.
- Resolution-supplied 8.5" monopole antenna