Restoration Hardware Rowan Series User manual

All Restoration Hardware cribs are
designed to meet the highest safety
standards and comply with all U.S. and
Canadian cribs and cradles regulations.
Page 1 of 13

Assembly Instructions For Crib
Page 2 of 13
Tools Necessary: Allen Key (included).
Flathead Scre driver (not included).
Phillips Scre driver (not included).
Note: It may be easier to assemble product ith t o people.
NOTE: When inserting bolts, turn clock ise until tight. Then loosen 1/2−3/4 of a turn. After crib is
completely assembled, return to each bolt and tighten. Use ax or soap on all bolts to facilitate
assembly.
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also
order parts by riting to the address above. Include the product model number, color, and a brief
description of the part. Call 1−800−762−1751
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Clean ith
mild soap on a soft rag. Rinse and dry thoroughly. If the crib is to be stored, store in a cool dry
place and carefully package all original hard are to protect from loss.
TOOLS AND INSTALLATION
ARNING: Read all instructions before
assembling this product. Keep
instructions for future use.
Restoration Hard are Baby & Child
2900 North Macarthur Drive
Tracy, California 95376
restorationhard are.com
Made in China
Distributed in the U.S.A. by:
Restoration Hard are Baby & Child
2900 North Macarthur Drive
Tracy, California 95376
restorationhard are.com
Model No: 5783−0612
ˆRo an Collection˜
Model No: 5983−0612
ˆRo an Collection˜

Page 3 of 13
ARNING: Infants can suffocate on soft bedding. Never
add a pillow, comforter or padding.
ARNING: Failure to follow these warnings and the
assembly instructions could result in serious injury or death.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
backs to sleep, unless other ise advised by your physician.
Strings can cause strangulation! DO NOT place items ith a string around a child’s neck,
such as hood strings or pacifier cords. DO NOT suspend strings over a crib or attach
strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
DO NOT place crib near indo here cords from blinds or drapes may strangle a child.
When child is able to pull to a standing position, set mattress to lo est position and
remove bumper pads, large toys and other objects that could serve as steps for climbing
out.
After raising side, make sure latches are secure.
DO NOT leave child in crib ith side lo ered. Be sure side is in raised and locked position
henever child is in crib.
When a child’s height reaches 90 centimeters (35 inches), the crib shall no longer be
used, and the child should be placed in a youth or regular bed.
Check this product for damaged hard are, loose joints, missing parts or sharp edges
before and after assembly and frequently during use. DO NOT use crib if any parts are
missing, damaged or broken. Contact Restoration Hard are for replacement parts and
instructional literature if needed. DO NOT substitute parts.
DO NOT use a ater mattress ith this crib.
If refinishing, use a non−toxic finish specified for children’s products.
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE
USE.
Never use plastic shipping bags or other plastic film as mattress covers because they can
cause suffocation.
Infants can suffocate in gaps bet een crib sides and a mattress that is too small.
CAUTION: Any mattress used in
this crib must be at least 27−1/4
inches by 51−5/8 inches ith a
thickness not exceeding 6 inches.
IMPORTANT SAFETY INFORMATION FOR CRIBS

Page 4 of 13
ARNING
Do not use this crib if the enclosed or attached instructions
cannot be strictly adhered to. Do not use this crib if the child is
able to climb out unaided or is taller than 90 cm. Do not place
cords, straps or similar items that could become ound around
the child’s neck in or near this crib. Ensure that the sides are
properly latched or locked in place hen the crib is occupied. The
mattress used ith this crib should not be more than 15 cm thick
and should be of such length and idth that the gap bet een the
mattress and the sides of the crib is not more than 3 cm hen the
mattress is pushed into the corner of the crib.
Parents should inspect the crib regularly −− before putting the
child in the crib each day −− and confirm that every component of
the crib is properly and securely in place.
IMPORTANT SAFETY INFORMATION FOR CRIBS
ARNING
Failure to follow these warnings and the assembly instructions could
result in serious injury or death from entrapment or strangulation.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
The mattress intended for use on the bed shall be a full−size crib mattress having
minimum dimensions of 51−5/8 in. (1310 mm) in length, 27−1/4 in. (690 mm) in idth and 4
in. (100 mm) in thickness, not exceeding 6 in. (152 mm) in thickness.
DO NOT place bed near indo s here cords from blinds or drapes may strangle a child.
DO NOT place items ith a string, cord, or ribbon around a child’s neck, such as hood
strings or pacifier cords.
DO NOT suspend strings over a toddler bed for any reason.
FOR TODDLER BEDS AND DAY BEDS ONLY. A child using this bed should be at least
15 months of age and should not eigh more than 50 lbs. (22.7 kgs.).
IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS

Item Identification
For ease of identification, all parts are labeled to correspond to
the Step number in which the part is used.
Step #2 Side frame &
stretcher bar assembly
(Page 7 of 3)
Step #3 Mattress support
height adjustment
(Page 8 of 3)
Step #4 Mattress support
Attachment to stretcher bars
(Page 9 of 3)
Step #6 Drop side assembly
(Page of 3)
Step #7 Drop side operation
(Page 2 of 3)
Step #5 Stationary side assembly
(Page 0 of 3)
Step #8 Toddler rail assembly
(Page 3 of 3)
Page 5 of 3
Step # Feet Assembly
(Page 6 of 3)

STEP #1
TURNED FEET & SIDE FRAME
ASSEMBLY
Turned Feet (x 4)
Side Frame (x 2)
Page 6 of 3
Detail A
Side frames
Turned foot
Turned foot
Turned foot
Turned foot
Insert threaded bolt in turned foot into
bottom of side frame and tighten until
snug.
Do not over tighten.
Threaded bolt
Turned foot
Bottom of
Side frame

STEP #2
SIDE FRAME &
STRETCHER BAR ASSEMBLY
Side Frame (x 2)
Stretcher Bar (x 2)
Note: Do not fully
tighten at this time
Insert barrel nuts into
holes in stretcher bar
Align threaded hole in
barrel nut with bolt (BB)
Note: Slot on barrel
nut faces outward
Page 7 of 3
Side frame
Side frame
1A
1B
(CC)
(CC)
(CC)
(AA)
(AA)
(AA)
(BB)
(BB) (BB)
(DD)
Stretcher bar
Stretcher bar
Detail A
Hardware needed for Step #2:
(AA) K.D. Barrel Nuts (x 4 pieces)
(BB) 3- /8 in. Bolts (x 4 pieces)
(CC) Dowel Pin (x 4 pieces)
(DD) Allen Wrench ( piece)
(BB)
(DD) Allen Wrench ( piece)
(CC) Dowel pin (x 4 pieces)
(BB) 3- -8 in. bolts (x 4 pieces)(AA) K.D. Barrel nuts (x 4 pieces)
Hardware Step # 2

STEP #3
MATTRESS SUPPORT
HEIGHT ADJUSTMENT
Mattress support (x )
Hardware needed for Step #3:
(EE) Mattress nut (x 4 pieces)
(FF) -3/8 in. Mattress bolt (x 4 pieces)
(GG) Mattress washer (x 4 pieces)
(HH) 3/8 in. lock washer (x 4 pieces)
(DD) Allen Wrench ( piece)
Page 8 of 3
Note: Do not fully
tighten at this time.
(GG)
(EE)
(FF)
Highest Level
Lowest Level
Detail A
3A
3B
3C
3D
Note: Highest level for infants
(HH) 3/8 Lock washer (x 4 pieces)
(GG) Mattress Washer (x 4 pieces)(FF) -3/8 in. Mattress Bolt (x 4 pieces)
(EE) Mattress Nut (x 4 pieces)
Hardware Step # 3
(HH)
(DD) Allen Wrench ( piece)
Note: Mattress support is easily
adjustable to varying heights by
removing hardware from current
level and inserting into different
hole for higher or lower level.

STEP #4
MATTRESS SUPPORT
ATTACHMENT TO
STRETCHER BARS
Mattress support (x )
Note: Do not fully
tighten at this time.
(DD)
(HH)
(GG)
(EE)
Detail A
3A
3B
3C
3D
Page 9 of 3
Hardware needed for Step #4:
(EE) Mattress nut (x 4 pieces)
(FF) -3/8 in. Mattress bolt (x 4 pieces)
(GG) Mattress washer (x 4 pieces)
(HH) 3/8 in. lock washer (x 4 pieces)
(DD) Allen Wrench ( piece)
(FF)
(HH) 3/8 Lock washer (x 4 pieces)
(GG) Mattress Washer (x 4 pieces)(FF) -3/8 in. Mattress Bolt (x 4 pieces)
(EE) Mattress Nut (x 4 pieces)
Hardware Step # 4
(DD) Allen Wrench ( piece)

STEP #
STATIONARY SIDE
ASSEMBLY
Stationary Side (x )
Hardware needed for Step # :
(II) 2-5/8 in. Bolt (x 4 pieces)
(DD) Allen Wrench ( piece)
Note: Do not fully
tighten at this time.
(II)
(DD)
Detail A
4A
4B
4C
4D
Stationary Side
Page 0 of 3
(DD) Allen Wrench ( piece)(II) 2-5/8 inch bolt (x 4 pieces)
Hardware Step #5

STEP #6
DROP SIDE ASSEMBLY
Drop side (x )
Page of 3
Detail A
Upper bushing
Detail B
Lower guide stud
To attach drop side, insert top of upper track on to upper bushing on both ends.
Then align lower guide stud with slot in lower track of drop side. Pull up on drop side
to engage. Tighten all hardware at this time.
Upper track in
Drop side
Lower track in
Drop side
Hardware needed for Step #6:
(KK) Upper bushing (x 2 pieces)
(LL) Lower guide stud (x 2 pieces)
(MM) Upper bushing screw (x 2 pieces)
(KK)
(KK)
(KK)
(MM)
(MM)
(MM)
(LL)
(LL)
(LL)
Hardware Step #6
(KK) Upper bushing (x 2 pieces) (LL) Lower guide stud (x 2 pieces)
(MM) Upper bushing screw (x 2 pieces)

STEP #7
DROP SIDE OPERATION
Page 2 of 3
Stand at the middle of the drop side and hold the
top rail with one hand. Raise the drop side
slightly to enable you to release the latch by
pushing on the drop side with your knee.
The drop side will now lower. Raise the drop side
and it will automatically lock at the upper position.
Always make sure the drop side is properly secured.
Push in
with knee Move down

STEP #8
TODDLER RAIL ASSEMBLY
Toddler Rail (x 2)
Page 3 of 3
Detail B
Metal hook on toddler rail
Stretcher bar
Loosen all tightened bolts
from near & far side frames.
Spread front of crib open
enough to get toddler rail
hooks between crib side
frames. Assemble toddler
rails to side frame on far
end by hooking into
provided slots while
aligning stretcher bar.
Assemble toddler rails to
side frame on near end by
hooking into provided slots
while aligning stretcher bar.
Retighten all bolts to snug
fit.
Hardware needed for Step #8:
(JJ) /2 in. Bolt (x 2 pieces)
(DD) Allen Wrench ( piece)
(MM) Upper bushing screw (x 2 pieces)
Note: Remove (KK) top
bushings & (LL) bottom
studs.
Detail A
(JJ)
(JJ)
(MM)
(MM)
Stationary side
of crib
Drop side
of crib
Hardware Step # 8
(JJ) /2 inch plug bolt (x 2 pieces) (MM) Upper bushing screw (x 2 pieces)
(DD) Allen Wrench ( piece)
Loosen end bolts