RevAir Reverse-Air Dryer User manual

ALL YOU NEED TO KNOW
operating manual | rev 2.0
Visitez support.myrevair.com pour consulter ce manuel en français.
Visite support.myrevair.com para revisar este manual en español.
RevAir Serial Number:
RevAir Education: support.myrevair.com
Contact Support: [e-mail]
SAVE THESE INSTRUCTIONS

myrevair.com
2
Distributed by RevAir LLC. Macedonia, Ohio 44056
myrevair.com Model#: RA90001, RA90003
Table of Contents
Important Safety Instructions & Warnings
Before using this device 3-5
Thank You
Register your device 6
RevAir Is Here
What’s in the box? 7
Parts & Functions
What does this thing do? 8-9
Device Assembly
Get it together 10-11
Using Your RevAir Device
Before you get started 12-13
How to Rev Your Hair
New technology means new techniques 14
Device Maintenance
Keep it clean 15-18
Storing Your RevAir
Best practices 19
Looking After Your RevAir Device
A little TLC 19
Disposal Information
It’s hard to say goodbye 19

myrevair.com 3
Important Safety Instructions
BEFORE USING THIS DEVICE, READ ALL INSTRUCTIONS AND
CAUTIONARY MARKINGS IN THIS MANUAL AND ON THE DEVICE.
WARNING
When using an electrical device, basic precautions should always be followed, including the following:
THESE WARNINGS APPLY TO THE DEVICE, AND WHERE APPLICABLE, TO ALL TOOLS,
ACCESSORIES, OR MAIN ADAPTORS.
01. This device is for household use only and not commercial processes.
02. Never use while sleeping.
03. When this device is used by children, or individuals with limited physical, sensory or reasoning
capabilities, close supervision is necessary.
04. Do not allow to be used as a toy. Close attention is necessary when used by or near children.
Children should be supervised to ensure that they do not play with the device.
05. Do not use as a vacuum cleaner or for any vacuuming purposes such as picking up and/or
collecting small items or debris.
06. Do not insert anything other than hair into the wand.
07. Do not operate this device outside or where oxygen is being administered.
08. CAUTION: At Reverse-Air Speed Level 1, use Low (I) or No (O) Heat. High Heat should only be
used when Reverse-Air Speed Dial is set at Level 2 or higher.
09. If the device is used in a bathroom, unplug after use. The proximity of water presents a hazard even
when this device is switched o.
10. Do not place the wand on any surface during use.
11. Do not place the Base Unit on the oor while operating.
12. WARNING: Do not use this device near bathtubs, showers, basins or other vessels containing
water.
13. Do not operate this device with an extension cord.

myrevair.com
4
14. Do not operate this device with a voltage converter.
15. Only plug this device into a 120V/60hz 15amp outlet.
16. If the supply cord is damaged, it must be replaced or repaired by RevAir, its service agent or
similarly qualied persons in order to avoid a hazard.
17. This device has a manual, resettable ALCI safety feature to prevent electric shock. If your device
turns o, unplug it from the power outlet, and press the RESET button. Plug it into the power outlet
once again, and power on. If it still does not work, check to see if the power outlet has a resettable
safety device that needs to be reset. Alternatively, try another outlet to determine whether it is an
electrical issue rather than a device issue. Should those methods fail contact RevAir Customer
Support at [e-mail] or [phone].
18. To ensure the ALCI safety feature is working properly, perform the following steps each time you
use this device.
•With the unit unplugged, press the Reset button on the ALCI plug.
• Plug the device into an AC outlet, press the Test button. The Reset button will pop out.
This veries that the safety feature is operating properly. If the Reset button does not pop out, do
not use the device.
Contact RevAir Customer Support at [e-mail] or [phone] for repair.
CAUTION
MAY BE HOT!
CAUTION
SURFACES
MAY BE HOT!

myrevair.com 5
19. This device includes over temperature sensors. If the unit becomes overheated while using it,
the heater will stop and the Lighted Handle will blink quickly. If the unit continues to overheat
because of a dirty or clogged lter, the heat and reverse-air motor will shut down until it has cooled
suciently.
20. For additional protection, the installation of a residual current device (RCD) having a rated residual
operating current not exceeding 30 mA is advisable in the electrical circuit supplying the bathroom.
Ask your installer for advice.
21. Hair sections too large can limit air ow and result in heater turning o due to over temperature
sensor. If the heater turns o, the unit will continue to operate. Reduce hair section size to elimi-
nate over temperature turn o. The heat shut-o will be indicated by a change in vacuum sound
during use.
22. CAUTION: The Air Outlet (Base) and Heat Chamber Air Inlet (Wand) surfaces may be hot. Keep
the Air Outlet at least two feet away from walls, fabrics or any surface.
23. Do not allow anything to block the Air Outlet on Base or Heat Chamber Air Inlet on Wand.
24. Do not handle any part of the plug or device with wet hands.
25. Do not put any liquids on or into the RevAir Base, Hose or Wand.
26. Do not force the plug’s polarized pin into power outlet/socket if it does not t.
27. Do not unplug by pulling on the cable. To unplug, grasp the plug housing, not the cable.
28. Do not stretch the cord or place the cord under strain. Keep the cord away from heated surfaces.
Do not wrap the cord around the device. Cord should only be wrapped around the intended Cord
Wrap Plate.
29. Refer to the Device Maintenance section of this manual for maintenance instructions.
30. Do not disassemble this device as incorrect reassembly may result in an electric shock or re.
Contact RevAir Customer Support at [e-mail] or [phone] when service or
repair is required.
31. This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
32. If this device is not working properly, has been dropped, damaged, left outdoors, or has come into
contact with water, do not use and contact RevAir Customer Support at [e-mail]
or [phone].

myrevair.com
6
Thank you for purchasing RevAir, the
world’s rst and only Reverse-Air Dryer.
If you have any questions about your RevAir device, contact RevAir Customer Support at [e-mail] or
[phone] with your serial number and details of where/when you purchased your device.
Most questions can be answered over the phone by our trained RevAir Customer Support team.
Visit support.myrevair.com for online help, videos, general tips and useful information about RevAir.
The serial number can be found on the rating plate located on the back of the Base Unit.
Write your serial number for future reference on the front page of this manual.
To help us ensure you achieve the best possible results and receive prompt and ecient service, please
register as a RevAir device owner. There are two ways to do this:
• Online at support.myrevair.com
• Telephone RevAir Customer Support at [phone]
Please register as a RevAir device owner
800280
JAN-19
S/N: XXXXXXXXXXX
Model # RAXXXXX
REVX
120V/60Hz/13.5A
Net Wt:10lb/4.5kg
Made In Mexico for RevAir, LLC. Designed in USA
RevAir Serial Number
(S/N:)

myrevair.com 7
Patented reverse-air and heat technology envelops hair completely, drying it from root to end. At the same
time, reverse-air’s natural force creates the tension needed to eortlessly dry hair straight.
In addition to delivering straight, sleek, incredible results, RevAir is:
Doubles Drying Eectiveness Less Heat Means Less Damage Does the Hard Work for You
FASTER
RevAir is here and nothing will ever
be quite the same.
HEALTHIER EASIER
IN THE BOX RevAir Reverse-Air Dryer
Heat Producing Wand
(detachable from hose)
Hose
(attached to lter cover panel)
Reverse-Air Base Unit Removable Filter
(resides inside the base unit)
NOTE: Hose shown shortened
for illustration purposes only.
NOTE: For convenience, the
Wand will be shipped
pre-attached to the hose.

myrevair.com
8
Hose
Connector
4. Filter Panel
Filter Panel
Latch
Strain Relief Filter Notch Base Housing Notch
3. Reverse-Air
Speed Dial
2. Main Power
On/O Switch
6. Lighted Handle
(Warning Notication)
5. Filter
Heat Chamber Cover
Heat Chamber Screen
(interior)
1. Temperature Control
Wand
Connector
Reverse-Air Base Unit Fig. 2.0
Heat Producing Wand Fig. 1.0
Parts & Functions RevAir Reverse-Air Dryer
NOTE: Hose shown shortened
for illustration purposes only.
1. Temperature Control Fig. 1.0
•High, Low and No Heat settings
•No Heat setting allows cool air to seal in the shine
2. Main Power On/O Switch Fig. 2.0
3. Reverse-Air Base Unit Fig. 2.0
•In addition to the O setting, 7 additional speed
settings on the dial allow adjustment of reverse-air
tension
4. Filter Panel Fig. 2.0
•Panel remains connected to Hose
•Rotate Filter Panel Latch counter-clockwise to
remove Filter Panel
5. Filter Fig. 2.0
•Filter Notch must align for proper insertion
•Filter must be installed for Base Unit to function
6. Lighted Handle (Warning Notication) Fig. 2.0
•Glows steady when power is on
•Lights a slow flash sequence to notify that the Filter
and/or Filter Panel is not correctly locked in place
(Base Unit will not operate)
•Lights a fast flash sequence if the Base Unit
overheats (Base Unit will still operate, but heat will shut
off until cooled down)
Wand
Mouth

myrevair.com 9
Heat Producing Wand Fig. 3.0
Reverse-Air Base Unit Fig. 4.0
Circuit Breaker
12. Cord Wrap
Plate
10. Air Outlet
9. Wand Docking
Hook
Lighted Handle
(Warning Notication)
8. Wand Docking
Groove
Wand
Connector
Heat Chamber Screen
Air Inlet
Heat Chamber
7. Heat Chamber Cover
7. Heat Chamber Cover Fig. 3.0
• Filters incoming air into the Heater
8. Wand Docking Groove Fig. 3.0
• Line up with Wand Docking Hook (Fig. 4.0.9)
located on the Base Unit for secure storage
9. Wand Docking Hook Fig. 4.0
•For easy storage of Wand on Base Unit
10. Air Outlet Fig. 4.0
•Never block the Air Outlet or place close to a wall or
surface, doing so may cause the unit to overheat
•Do not touch the Air Outlet area, as it may be hot
11. Exhaust Filter Fig. 4.0
•For noise suppression and additional air ltration
12. Cord Wrap Plate Fig. 4.0
•For manual cord storage
Parts & Functions RevAir Reverse-Air Dryer
11. Exhaust Filter

myrevair.com
10
After unpacking your new RevAir device:
Device Assembly
Insert Filter into Base Unit. Filter Notch must line up with intended groove to t in properly. Without Filter
installed and Filter Notch groove aligned properly, Base Unit will not power on. Every few uses, it is important
to empty and clean Filter.
2.
1. For convenience, the Wand will arrive pre-attached to the Hose. For Wand removal instructions refer to the
maintenance section of this manual (pgs. 15-18).