REXROTH EFC3600 Series User manual

EFC3600 Quick Set up Guide
1

EFC3600 Wiring Single phase 230V AC
Connections and wiring
! EFC 3600
! Connection 200VAC
L1+ L2
2

EFC3600 Wiring 3 Phase 400V AC
Connections and wiring
! EFC 3600
! Connection 3x400VAC
L1 + L2 + L3
3

Intern | 22.04.2013 | DC-IA/SFS31 |Carsten Kobusch | EFC3600 Training 2013 EN CK V01.pptx | © Bosch Rexroth AG 2013. Alle Rechte vorbehalten, auch bzgl.
jeder Verfügung, Verwertung, Reproduktion, Bearbeitung, Weitergabe sowie für den Fall von Schutzrechtsanmeldungen.
EFC3600 Operating Panel
Operating Panel
4

EFC3600 Quick Set Up
! Motor data
! S2.00 Rated motor frequency 50Hz
! S2.01 Rated motor speed 1450 rpm
! S2.02 Rated motor power 2 kW
! S2.03 Rated motor voltage 415V
! S2.04 Rated motor current 0,23A
! S2.05 Power factor 0,76
! S2.15 Auto tuning
Value Description
0 No action
1 Calculation of motor data
2 Auto adjustment with motor in standstill
3 Auto adjustment with running motor
5 Intern | 22.04.2013 | DC-IA/SFS31 |Carsten Kobusch | EFC3600 Training 2013 EN CK V01.pptx | © Bosch Rexroth AG 2013. Alle Rechte vorbehalten, auch bzgl.
jeder Verfügung, Verwertung, Reproduktion, Bearbeitung, Weitergabe sowie für den Fall von Schutzrechtsanmeldungen.

EFC3600 Quick Set up
1) Running from Panel Potentiometer & Buttons
! b0.05 = 1 Load standard parameters
! b0.02 = 2 Access all authority settings
• These parameters below are automatically set after b0.05=1
! b1.00 = 0 Frequency set point via potentiometer
! b1.02 = 0 Inputting commands via panel buttons
Speed/Frequency Command: set by potentiometer
Start Command: initiated by RUN Button
Stop Command: initiated by STOP Button
6

EFC3600 Quick Set up
2) Running from External I/O Terminal, Frequency Set by Potentiometer
! b0.05 = 1 Load standard parameters
! b0.02 = 2 Access all authority settings
! b1.00 = 0 Frequency set point via potentiometer
! b1.02 = 1 Inputting commands via external I/O terminals
! E0.00 = 0 Forward/Stop, Revese Stop 2 Wire Control
! E0.01 = 23 Set External terminal X1 = FWD
! E0.02 = 24 Set External terminal X2 = REV
! s3.30 = xx sec FWD and REV Dead Zone Time
Speed Command: set by potentiometer
Start Command: X1= On for FWD, X2 = On for REV
Stop Command: X1= OFF, X2=OFF or STOP on panel
7

EFC3600 Quick Set up
3) Running from External I/O Terminal + Jogging, Frequency Set by Potentiometer
! b0.05 = 1 Load standard parameters
! b0.02 = 2 Access all authority settings
! b1.00 = 0 Frequency set point via potentiometer
! b1.02 = 1 Inputting commands via external I/O terminals
! E0.00 = 0 Forward/Stop, Revese Stop 2 Wire Control
! E0.01 = 23 Set External terminal X1 = FWD
! E0.02 = 24 Set External Terminal X2 = REV
! E0.03= 21 Reset Terminal X3=ON
! E0.04 = 25 X4 = Jog FWD
! E0.05= 26 X5 = Jog REV
! S3.0 = xx Jog frequency
Speed Command: set by potentiometer
Start Command: X1= On for FWD, X2 = On for REV
Jog Command: X4 =On,X5 = off JOG FWD Overrides FWD & REV
X5= On, X4 = off JOG REV Overrides FWD & REV
Stop Command X1= Off, X2=Off or STOP (for FWD & REV)
X4= Off, X5 = Off (for Jogging Stop)
8

EFC3600 Quick Set up
4) Running from External I/O Terminal, Fixed Frequency via I/O
! b0.05 = 1 Load standard parameters
! b0.02 = 2 Access all authority settings
! b1.00 = 6 Frequency set point via External I/O
! b1.02 = 1 Inputting commands via external I/O terminals
! E0.00 = 0 Forward/Stop, Revese Stop 2 Wire Control
! E0.01 = 1 Set External terminal X1 = multi speed 1
set frequency E2.10
! E0.02 = 2 Set External Terminal X2 = multi speed 2
set frequency E2.11
! E0.03 = 3 Set External Terminal X3 = multi speed 3
set frequency E2.13
! E0.04= 23 X4= FWD
! E0.05= 24 X5 = REV
! B1.04= Frequency when X1 X2 & X3=0
Speed Command: combination X1,X2,X3 ( Binary Number Combination)
Start Command: X3= ON for FWD, X4 = On for REV
Stop Command: X3= Off, X4=Off
9 Intern | 22.04.2013 | DC-IA/SFS31 |Carsten Kobusch | EFC3600 Training 2013 EN CK V01.pptx | © Bosch Rexroth AG 2013. Alle Rechte vorbehalten, auch bzgl.
jeder Verfügung, Verwertung, Reproduktion, Bearbeitung, Weitergabe sowie für den Fall von Schutzrechtsanmeldungen.

EFC3600 Quick Set up
5) Running with Panel UP/Down Arrows
! b0.05 = 1 Load standard parameters
! b0.02 = 2 Access all authority settings
! b1.00 = 1 Frequency set point via panel Arrows UP/DOWN
! b1.02 = 0 Inputting commands via Panel
! b1.04= 0Hz Set Start Frequency
! b1.11= Direction 0 = FWD
1 = REV
Speed Command: UP ▲Increases Speed, Down ▼Decrease Speed
Start Command: RUN Button
Stop Command: STOP Button
10

EFC3600 Quick Set up
6) Running External I/O with UP / DOWN / ZERO Inputs
! b0.05 = 1 Load standard parameters
! b0.02 = 2 Access all authority settings
! b1.00 = 4 Frequency set point via external UP/DOWN
! b1.02 = 1 Run commands via External I/O
! E0.01= 9 X1 = Frequency increment UP Command
! E0.02=10 X2 = Frequency decrement DOWN command
! E0.03=11 X3 = Frequency ZERO command
! E0.04=23 X4 = FWD
! E0.05=24 X5 = REV
! S3.32 = xx Frequency UP/DOWN Ratio
Speed Command: X1 = ON UP Increases Speed
X2 = ON Down Arrow Decrease Speed
X3 = ON Zero Speed
Start Command: X4= On (FWD), X5= On (REV)
Stop Command: X4= Off (FWD), X5 = Off (REV) or STOP Button
11

EFC3600 Quick Set up
7) Running with an Analog Input Voltage
! b0.05 = 1 Load standard parameters
! b0.02 = 2 Access all authority settings
! b1.00 = 2 Frequency set point given via analog input voltage
! b1.02 = 1 Inputting commands via External Input
! E0.01 = 23 X1= FWD
! E0.02 = 24 X2 = REV
Or
! b1.02=0 Run Command Via Panel
Speed Command: 0-10V Analog Input @ terminals VR1 (0-10V) & Gnd
Start Command: X1= ON FWD, X2=ON REV ( when b1.02=1)
RUN Button (when b1.02-0)
Stop Command: X1 = OFF FWD, X2=OFF REV
STOP Button ( when b1.02=0)
12

EFC3600 Quick Set up
8) Running with Analog Input Voltage switching to 2nd Frequency Source &/or Run Source
! b0.05 = 1 Load standard parameters
! b0.02 = 2 Access all authority settings
! b1.00 = 2 Frequency set point given via analog input voltage
! b1.02 = 1 Inputting commands via External Input
! E0.01 = 23 X1= FWD
! E0.02 = 24 X2 = REV
! E0.03 = 18 X3 = Secondary Frequency Source Active
! E0.04 = 22 X4 = Secondary Run Command Active
! b1.16 = 0 Frequency command from potentiometer
! B1.17 = 0 Run command via Panel
Speed Command: refer to previous pages
Running with an Analog Input Voltage or
Running from panel potentiometer
Start Command: as above
Stop Command: as above
13

EFC3600 Quick Set up
9) Simple PLC
! b0.05 = 1 Load standard parameters
! b0.02 = 2 Access all authority settings
! b1.00 = 6 Frequency set point given via MultiSpeed
! E2.30 = 1 Simple PLC Active, one cycle then stops
! E0.04 = 23 X 4 = FWD
! E0.05 = 24 X5 = REV
Step 1
! b1.04= xx Start Frequency
! E2.35 = 011 Step 1
! E2.36 = xx Time in sec
Step 2
! E2.10= xx Frequency Step 2
! E2.37 = 012 Step 2
! E2.38 = xx Time in sec
Step 3
! E2.11= xx Frequency Step 3
! E2.39 = 013 Step 3
! E2.40 = xx Time in sec
:
Speed & Start Command: X4= On FWD or X5= On REV
Stop Command: X4= Off or X5 = Off
14