RGT OFF-ROAD CRAWLER User manual

The product hasconducted IQC (InputQuality Control) andfull inspection beforedelivery. The manufacturer isresponsible
for quality assurance.Remote Control modelis assembled manually, and thenthere may havesome defects inthe production
process. Once theproduct is modifiedor incorrect operation,it cannot applyfor replacement andreturn services, for the parts
and accessories maybe damaged. Pleasecontact the retailseller for after-sales service when needed.
The product conformsto technical requirementsof export safety regulations.
Factory Address: HuangJiang Town,Dong Guan City,Guang Dong Province,China
Production Date: referto packing instruction
NO.EX86170
MADE IN CHINA
OFF-ROAD CRAWLER

Thanks for purchasingour RC car. The power system for RC model can be very dangerous,so please read this
manual carefully. In that we haveno control over the correct use, installation, application, ormaintenance of our
products, no liabilityshall be assumed nor accepted for any damages, lossesor costs resultingfrom the use of
the product.Any claims arising from the operating, failure of malfunctioningetc. will bedenied. We assume no
liability for personalinjury, consequential damages resulting from our productor our workmanship.
02 03

One car
Transmitter
2.The items inside the box.
4-1.Install Charged Batteries In Car.
Manual
04 05
1. Please read the manual carefully and prepare the following things before use.
3. Please check the whole product condition when open the package.
4.0mm
4.5mm
5.5mm
7.0mm
Accessories
3-5. Vehicle parts
Battery Tray
Baffle
ESC
Dig Servo
2Speed Servo
Receiver Box
Front Body Hole
Transmission
Bumper
Winch Servo
Motor
Steering Servo
Steering Knuckle
Housing
Chassis Plate
Chassis Rails
Foot Pedal
Driveshaft
Shock Absorber
Sway Bar+Links
Lower 4-Link Bar Upper 4-Link Bar
Wheel
Clevis Joint
Winch steel wire
Please turn thebutton in clockwise(90 degree) asshown, then
install the preparedbattery pack.
NOTE: Please check thebattery
plug type wheninstall. The required
plug type is"T"plug. With theincorrect plug,
the car couldnot run.

ON
06 07
Power Switch
LED Power Switch
Servo 1
LED
Servo 2
Servo 3
Servo 4
ON
CH7
CH8
OFF
WARNING:
4-2. Battery Specifications for Product 4-3.Scheme of installation
NOTICE
Please check the battery voltage before use. Please use a qualified charger to charge the newly purchased
battery. (please read the charging steps inmanual when necessary)
NO battery includes in factory.Recommend?battery: 2S~3S LIPObattery or 5-9 cells NIMH battery
(please match the ESC mode with the corresponding battery type)Pay attention to the battery size and plug
specification when purchasing.The maximum battery measurement is 142*48*55mm LxWxH).
E.S.C
High/Low Gear
Steering
Black
Black
Blue
Yellow
RedRed
Red
Front Fog Light
Light
Light
Receiver (X10F-G)
1
2
3
4
5
7
8
5-1. XA8 2.4GHZ Radio System
Steering Trim
CH1
(ST.Trim)
Steering D/R
CH1
Throttle Trim
CH2
(TH.Trim)
Throttle D/R
CH2
CH4 -LED
CH3 -LED
CH7 CH8
Wheel Angle(CH1)
Antenna
Throttle Trigger(CH2)
Power Switch-LED ON
CH1
CH7 CH2
CH8
CH3
CH9 CH4
CH10
Reverse Switch
Reverse Switch
Light Connect
CH1
CH10
CH8
CH7
CH9
CH2 CH3 CH4
Antenna
Bine
PPM
Mode
NO. X10F-G NO. X10E-150
Winch Servo
DIG Servo
As shown:
1. Press thebutton, the LED is on.
2. Press thebutton twice,
the LED flashes.
3. Press thebutton again,
the LED isoff.
Voltage Return LED
Voltage Return

(Steering D/R)
(ST.TRIM) (TH.TRIM)
1.Move the controlwheel to theleft,
vehicle turns left.
2.Do not movethe control wheel,
the front wheelsare aligned and
the vehicle goesstraight in line.
3.Move the controlwheel to the
right, vehicle turnsright.
01
1
2
2
3
3
01
1
2
2
3
3
0
50
75
25
100 0
50
75
25
100
The ST.TRIM is the trims for Ch1(steering),You can trim the
ST.TRIM / R :
ST.TRIM / L : Steering Trim until it fulfills your desired steering angles.
ST.D /Ris for servo travel adjustment,which can be
multiplexed asCH2 (throttle).
ST.D / R +: increase ser vo travel.
ST.D / R -: decrease ser vo travel.
(Throttle D/R)
TH.D / R +: increase throttle travel.
TH.D / R -: decrease throttle travel.
TH.TRIM / R:
TH.TRIM / L:
Note:
Please trim theThrottle Trim (TH. Trim)until the vehicle
stops in casethe vehicle goes forwards or backwards
itself just afterit is turned on.
If the frontwheels are not aligned,please trim"steering
trim" (ST.TRIM) until theyare aligned.
09
08
Forward Reverse
Brake
Neutral /
Throttle trigger,
has a total throw of 12 degrees, 12.5 degrees forward,
Forward
Reverse
Forward
Reverse
Neutral
and 12.5 degrees backward
TH.REV
Channel Reverse
The heavier youpull or push the trigger,
the faster accelerationwill be.
Vehicle goingforward
(Throttle Rev.at Normal position)
Vehicle goingbackwards
(Throttle Rev.at Reverse position)
The ST.REV switches are the reverse buttons for Ch1. If the switch is up it indicates reverse,
and the down Indicates normal.
Left Anti-clockwise
Steering Trim(ST. Rev) isused to reversethe direciton ofservo movement.
Vehicle turningleft when thecontrol wheel is turned to the left
(Steering Rev.At Normal position)
Vehicle turningright when thecontrol wheel is turned to the right (Steering Rev. at Reverse position)
The TH.REV switches are the reverse buttons for CH2. If the switch is up it indicates reverse, and the down
indicates normal.
The Throttle Rev. is usedto reverse the direction of motor rotation.
ST.REV
5-2. Transmitter Steering Trim and Throttle Trim
5-3. Transmitter Steering and Throttle Instruction
Note: Release thethrottle trigger button,
activate the brakemode automatically.
(Only for Crawler)
08
Bine
ON
ON
Left
Right
Wheel Angle
Steering wheel is
35 degrees From center to left or right
the maximum rotation of the
Increase adjustment step Increase adjustment step
Decrease adjustment step Decrease adjustment step
CH1
CH2
CH3
CH3 CH4
CH4
Right clockwise
1. Press andhold CH3 button (LED is on), the winch turns
in anticlockwise, thehook stretches, release the button,
the stretch actionstops.
Note: the hook requiresexternal force to stretch.
2. Press andhold CH4 button (LED is on), the winch turns
in clockwise, thehook contracts. Release the button, the
contract action stops.
Warning: The hook contracts15kg in maximum
(flat surface), ifsurpass, the winch servo and wire
will be damaged.
5-4 Servo Winch Hook Function
Winch Servo