RH Baby&child VERSAILLES CONVERSION CRIB User manual

VERSAILLES CONVERSION CRIB INSTRUCTIONS
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include
the product model number, color, and a brief description of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.
Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully package all original
hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After crib is completely assembled, return to each bolt and
tighten. Use wax or soap on all bolts to facilitate assembly
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
Page 1 of 12
All Restoration Hardware cribs are designed to meet the highest safety
standards and comply with all U.S. and Canadian cribs and cradles regulations.
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
2900 North Macarthur Dr. Tracy,
CA95376, USA
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7

Page 2 of 12
IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over over a crib or attach strings to toys.
·To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
·DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
·When child is able to climb out or reaches the height of 35 in (89 cm), the crib shall no longer be
used, and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. DO NOT use crib if any parts are missing, damaged or
broken. Contact customer service at 1-800-762-1751 for replacement parts and instructional
literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.

Page 3 of 12
IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27-1/4 INCHES BY 51-5/8 INCHES WITH A
THICKNESS NOT EXCEEDING 6 INCHES.
WARNING
Do not use this crib if you cannot exactly follow the instructions
that come with it.
Do not use this crib for a child who can climb out of it or who is
taller than 90 cm.
Do not place any cord, strap or similar item in or near this crib
that could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and be strangled.
Check this crib regularly before using it, and do not use it if any
part is loose or missing or if there are any signs of damage. Do
not substitute parts. Contact the manufacturer if replacement
parts or additions instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no thicker than 15 cm and is of such a size
that, when it is pushed firmly against any side of this crib, it does
not leave a gap of more than 3 cm between the mattress and any
part of any other side of the crib.

Page 4 of 12
IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51-5/8 inches (1310mm) in
length, 27-1/4 inches (690mm) in width and 4 inches (100 mm) in
thickness, not exceeding 6 inches (152 mm) in thickness.
·If guardrails are used as the mattress containment means,
guardrail(s) provided must be used to avoid the formation of a gap
between the mattress and the bed that could cause an entrapment.
·DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.

Page 5 of 12
Step #1 Lower side rail, headboard and footboard assembly (Page 6).
Step #2 Installation of upper side rail into the lower side rail assembly (Page 7).
Step #3 Installation of upper side rail into the headboard and footboard assembly (Page 8).
Step #4 Mattress support arm assembly.
Stabilizer rail assembly
Mattress height adjustment (Page 9)
Step #5 Installation of stabilizer rails into headboard and footboard assembly (Page 10).
Step #6 Toddler rails assembly (Page 11 & 12).
ITEM IDENTIFICATION
For ease of identification, all parts are labeled to correspond to the step number in which
the part is used.
HEADBOARD
FOOTBOARD
UPPER SIDE RAIL
MATTRESS SUPPORT
LOWER SIDE RAIL (RIGHT)
LOWER SIDE RAIL (LEFT)

Page 6 of 12
STEP #1
LOWER SIDE RAIL, HEADBOARD AND FOOTBOARD ASSEMBLY
STEP #1.1
Bring the Headboard and Footboard into upright position.
NOTE:
On inside lower faces of Headboard and Footboard are
holes with pre-installed nuts for the wooden dowels to
pass through which correspond with pre-installed wooden
dowels on the Lower Side Rail (Left).
STEP #1.2
Fasten the threaded rod through pre-installed nuts on
Headboard and Footboard. Bring the Lower side rail (left)
up to the Headboard and insert the Threaded rods through
the holes. Once Lower side rail (left) are set, insert
Curved washers and Lock washers and fasten these with
Hexagonal nuts provided. Please see DETAIL A.
NOTE: DO NOT OVER TIGHTEN
STEP #1.3
Repeat the above procedure with the Lower side rail (right)
to attach it to the Headboard, and then repeat to connect
both Lower side rail to the Footboard.
HARDWARE FOR STEP #1:
THREADED ROD (M8X100MM) = 8 PCS
CURVE WASHER = 8 PCS
LOCK WASHER = 8 PCS OPEN WRENCH = 1 PC
14 X 90
HEX NUT = 8 PCS
DETAIL A
Threaded Rod
Curve Washer
Lock Washer
Hex Nut Open Wrench

Page 7 of 12
STEP #2
INSTALLATION OF UPPER SIDE RAIL INTO
THE LOWER SIDE RAIL
STEP #2.1
Gently lay both Upper side rails on their
backs on a clean and non-abrasive surface.
STEP #2.2
Fasten the Minifix bolt through pre-installed
nuts underneath of Upper side rails. Please
see DETAIL B.
STEP #2.3
Remove the Minifix lock from the Minifix nut,
as in DETAIL C. Insert the Minifix nuts into
the holes on the Lower side rails, then use
a screwdriver to adjust the Minifix nuts to
make sure the hole on it is aligned with the
bore hole on the top of the Lower side rails
as in DETAIL D.
STEP #2.4
Align the Minifix bolt on the Upper side rails
into the Minifix nuts through the bore hole
on the top of the Lower side rails. Re-insert
the Minifix locks to secure the Minifix bolts
to the Minifix nuts, and the Upper side rails
will be fixed to the Lower side rails. See
DETAIL E.
NOTE: DO NOT OVER TIGHTEN
HARDWARE FOR STEP #2:
MINIFIX BOLT = 4 PCS
MINIFIX NUT/ MINIFIX LOCK = 4 SETS
ALLEN WRENCH = 1 PC
B
B
DETAIL B
Minifix Bolt
Minifix Lock
Minifix Nut
DETAIL C DETAIL D
Minifix Nut
DETAIL E
Minifix Lock

Page 8 of 12
STEP #3
INSTALLATION OF UPPER SIDE RAIL INTO
THE HEADBOARD & FOOTBOARD
STEP #3.1
On both ends of the Upper side rail are holes
for the bolt to pass through that correspond to
the holes on the posts for headboard and
footboard with pre-installed nuts. Align and
insert the Allen bolts (AA) in each hole and
tighten with Allen wrench provided, as in
DETAIL F.
After assembly, re-tighten all bolts to a snug
fit. DO NOT OVER TIGHTEN.
HARDWARE FOR STEP #3:
(AA) 1/4" X 1-3/4" BOLT = 8 PCS
ALLEN WRENCH = 1 PC
PLAIN WASHER = 8 PCS
LOCK WASHER = 8 PCS
(DD)
DETAIL F

Page 9 of 12
LOCK
WASHER
G
H
STEP #4
MATTRESS SUPPORT ARM ASSEMBLY
STABILIZER RAIL ASSEMBLY
MATTRESS HEIGHT ADJUSTMENT
DETAIL G
DETAIL H
HEX NUT
PLAIN
WASHER
ALLEN BOLT
(BB)
ALLEN
WRENCH
ALLEN WRENCH
OPEN WRECH
HEX NUT
LOCK WASHER
PLAIN WASHER
MATTRESS
SUPPORT
STABILIZER RAIL
HARDWARE NEEDED FOR STEP #4:
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
(BB) 1/4" X 1-3/8" BOLT = 8 PCS
LOCK WASHER = 8 PCS
PLAIN WASHER = 8 PCS
HEX NUT = 8 PCS
11 X 70
OPEN WRENCH = 1 PC
ALLEN WRENCH = 1 PC
STEP #4.1
Lay mattress support flat with stabilizer rail on each side.
NOTE:
On each end of the arm of the mattress support, there is a hole for the
bolt to pass through that corresponds to the holes located in the frame of
the mattress support.
STEP #4.2:
Insert the bolt into the desired hole of the frame through the hole on the
arm support. Fasten the bolt with plain washer, lock washers &
hexagonal nut provided. Repeat procedure on other arms of the
mattress support. See DETAIL G.
WARNING:
Set the mattress support to the desired height by adjusting the support
arms. The mattress support should be at its highest setting for
newborns, then adjusted to the lower positions as the child grows and
becomes mobile. Once the child is able to stand, the mattress support
should be at its lowest position.
STEP #4.3:
Install the stabilizer rail at ends of the arm support, as illustrated in
DETAIL H.

Page 10 of 12
STEP #5
INSTALLATION OF STABILIZER RAILS INTO
THE HEADBOARD & FOOTBORAD
STEP #5.1
On inside face of both Headboard and Footboard are
pre-installed metal brackets, designed to hold the
stabilizer rails. Set both ends of the stabilizer rails into
brackets, as illustrated in DETAIL I.
STEP #5.2
Once the stabilizer rails are set, gently tilt the crib as
illustrated in DETAIL J, then fasten the stabilizer rails
with bolt together with plain washer and lock washer
provided, as illustrated in DETAIL K.
HARDWARE NEEDED FOR STEP #5:
(CC) 1/4" X 13/16 " BOLT = 4 PCS
LOCK WASHER = 4 PCS
PLAIN WASHER = 4 PCS
ALLEN WRENCH = 1 PC
I
DETAIL I
DETAIL J
K
DETAIL K
(CC)

Page 11 of 12
STEP #6
TODDLER RAILS ASSEMBLY
STEP #6.1
Remove the Upper side rails of the crib
by loosening all the bolts together with
cam lock installed as well as the mattress
support.
STEP #6.2
Gently tilt the crib and release the bolts
underneath the metal brackets holding
the stabilizer rails.
STEP #6.3
Gently lay both toddler rails on their
backs on a clean and non-abrasive
surface. Fasten the Minifix bolt through
pre-installed nuts underneath of Toddler
rails. Please see DETAIL L.
STEP #6.4
Remove the Minifix locks from the Minifix
nuts, as per illustrated in DETAIL M.
Insert the Minifix nuts into the holes on
the Lower Side Rails, then use a
screwdriver to adjust the Minifix nuts to
make sure the hole on it is aligned with
the bore hole on the top of the Lower
Side Rails, as per illustrated in DETAIL N.
STEP #6.5
Align the Minifix bolt on the Toddler rails
into the Minifix nuts through the bore hole
on the top of the Lower Side Rails.
Re-insert the Minifix locks to secure the
Mini fix bolts to the Minifix nuts, and the
Toddler rails will be fixed to the Lower
Side Rails. See DETAIL O.
MINIFIX BOLT = 4 PCS MINIFIX NUT/ MINIFIX LOCK = 4 SETS
ALLEN WRENCH = 1 PC
HARDWARE FOR STEP #6
(PACKED INSIDE TODDLER RAIL)
(EE) 1/4" X 1/2" BOLT= 6 PCS
L
L
DETAIL L
Minifix Bolt
Minifix Lock
Minifix Nut
DETAIL M DETAIL N
Minifix Nut
DETAIL O
Minifix Lock

Page 12 of 12
STEP #6
TODDLER RAILS ASSEMBLY
STEP #6.6
On right end of the toddler rails are holes for the
bolt to pass through that correspond to the holes
on the posts for headboard with pre-installed
nuts. Align and insert the Allen bolts (removed
from step #6.1) in each hole and tighten with
Allen wrench provided, as in DETAIL P.
After assembly, re-tighten all bolts to a snug fit.
DO NOT OVER TIGHTEN.
NOTE: If mattress support is not in the lowest
position, unscrew mattress support bolts and
move the lowest position.
STEP #6.7
Repeat step #5. Installation of stabilizer rails into
the headboard and footboard (DETAIL Q).
After assembly, re-tighten all bolts to a snug fit.
STEP #6.8
Fill the holes located on the top of both sides of
the headboard and footboard by inserting bolt
(EE) provided (packed inside toddler rail) as in
DETAIL S.
DETAIL P
S
P
P
DETAIL Q
(CC)
(EE)
DETAIL S
(DD)