RH Baby&child Bennet Bunk Bed Full Over Full User manual

B E N N E T B U N K B E D - F U L L O V E R F U L L I N S T R U C T I O N S
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include the
product model number, color, and a brief description of the part.
Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth. Blot spills immediately and
wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen key (included)
Wrench (included)
Screwdriver (not included)
Note: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After bunks is completely assembled, return to each bolt and tighten.
Use wax or soap on all bolts to facilitate assembly.
112
/

IMPORTANT SAFETY INFORMATION FOR BUNK BED
1. Follow the information on the WARNINGS appearing on the upper bunk end
structure and on the carton.
2. Always use the specified size mattress, mattress support, or both to help
prevent the likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of
guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other
components are in their proper position, free from
damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement
parts.
10.Use of a night light may provide added safety precaution for a child using
the upper bunk.
11.Use guardrails on both sides of the upper bunk.
12.If the bunk bed will be placed next to a wall, the guardrail that runs the full
length of the bed should be placed against the wall to prevent entrapment
between the bed and the wall.
13. The use of water flotation mattress is prohibited.
14.STRANGULATION HAZARD - Never attach or hang items to any part of the
bunk bed that are not designed for use with the bed: for example, but not
limited to, hooks, belts, and jump ropes
15.Keep these instructions for future reference.
16.DO NOT remove warning label from bed.
17. 400Lbs Max Weight Capacity.
WARNING
DO NOT REMOVE THIS LABEL
TO HELP PREVENT SERIOUS OR FATAL
INJURIES FROM ENTRAPMENT OR FALLS:
1. Never allow a child under 6 years on upper bunk.
2. Use mattress which is 53''W x 75L x 7''H on Full upper
bunk and Full lower bunk.
3. Ensure thickness of mattress does not exceed 7" and
mattress is at least 5" below upper edge of guardrails.
4. Use guardrails on both sides of upper bunk.
5. Use ladder for entering and leaving upper bunk.
6. Prohibit horseplay on or under bed(s).
7. Prohibit more than one person on upper bunk.
8. If the bunk bed will be placed next to a wall the
guardrails that run the full length of the bed .
STRANGULATION HAZARD
9. Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for
example, but not limited to, hooks, belts, and jump
ropes.
212
/

PARTS INCLUDED
A [1] HEADBOARD
B [1] FOOTBOARD
C [1] STORAGE RAIL
D [1] LOWER SIDE RAIL
E [2] UPPER SIDE RAILS
F [2] CANOPIES
G1 [5] BED SLATS (LONG)
G2 [5] BED SLATS (SHORT)
H [2] LOWER PLATFORM PANELS
I [2] UPPER PLATFORM PANELS
J [1] LADDER
K1 [2] CURTAIN ROLL FOR HB - L=1380MM
K2 [2] CURTAIN ROLL FOR FB - L=1380MM
K3 [8] CURTAIN ROLL FOR SR - L=950MM
COMPONENT IDENTIFICATION AND HARDWARE
NO. ITEM DESCRIPTION QTY.
1Threaded Rod 12 pcs.
2Curved Washer 12 pcs.
3Lock Washer 12 pcs.
4
5Wrench 1 pc.
Hex Nut 12 pcs.
Flat Head Phillips Screw
(M4x20mm) 2 pcs.
Allen Bolt 12 pcs.
Round Head Screw
(M4x25mm) 68 pcs.
Plain Washer
Allen Key 1 pc.
Concealed metal bracket
(Male) 2 pcs.
Flat Head Phillips Screw
(M3x15mm) 4 pcs.
12 pcs.
NO. ITEM DESCRIPTION QTY.
6
7
8
9
Lock Washer 12 pcs.
NO. ITEM DESCRIPTION QTY.
10
11
12
NO. ITEM DESCRIPTION QTY.
13
Phillips Screwdriver
(Not provided) 1 pc.
14
NO. ITEM DESCRIPTION QTY.
TOOLS REQUIRED (NOT PROVIDED)
A
B
C
D
E
G1
G2
H
H
I
I
E
J
K2
K3
K3
312
/

IMPORTANT
These bed parts can be cumbersome and heavy, therefore the assistance of two or more people is recommended in order to prevent personal injury
and ensure the bed parts are not damaged during the assembly process.
ASSEMBLY INSTRUCTIONS
1. Lay the headboard (A) and footboard (B) on a flat surface.
2. Attach the threaded rods (1) into the fixed nuts in the post of the headboard/footboard by turning them manually. See FIGURE 1 and FIGURE 2.
3. Fully remove all the drawers out of the storage rail (C), as per illustration in FIGURE 3. NOTE: SEE DETAIL ON PAGE 10 TO REMOVE
DRAWER.
Fig.2
Fig.1
Fig.2
FIGURE 1
FIGURE 2
FIGURE 3
C
412
/

4. Attach the storage rail to the headboard (A), as per illustration in FIGURE 4. DO NOT FULLY TIGHTEN.
5. Attach the lower side rail (D) to the headboard as per illustration in FIGURE 5. DO NOT FULLY TIGHTEN.
6. Bring the upper side rail (E) in upright position and align the threaded rods on the headboard to the corresponding holes in the end of the upper
side rail. Attach the upper side rail to the headboard, as in FIGURE 6. DO NOT FULLY TIGHTEN. KEEP HOLDING THIS SIDE RAIL DURING
NEXT STEP.
7. Repeat step 6 to attach the other upper side rail to the headboard. KEEP HOLDING BOTH UPPER SIDE RAILS DURING NEXT STEP.
8. Bring the Canopy (F) in upright position and align the threaded rods on the headboard to the corresponding holes in the end of the Canopy. Attach
the Canopy to the headboard, as in FIGURE 7. DO NOT FULLY TIGHTEN. KEEP HOLDING THIS SIDE RAIL DURING NEXT STEP.
9. Repeat step 8 to attach the other canopy to the headboard. KEEP HOLDING BOTH UPPER SIDE RAILS DURING NEXT STEP.
Fig.7
Fig.7
Fig.6 Fig.6
Fig.5
Fig.4
876
876
9
9
FIGURE 4
FIGURE 5
FIGURE 6 2
34
FIGURE 7
A
512
/

10. Align the threaded rods on the footboard (B) to the corresponding holes at the end of the storage rail (C), lower side rail (D), upper side rails
(E) and Canopies (F). Align the locator pins on the end of the storage, the side rails and canopies to the corresponding holes in the footboard.
Insert the footboard into the storage, the side rails and the canopies.
11. Repeat from step 4 to step 9 to attach the storage, the side rails and the canopies to the footboard.
12. After assembly, re-tighten all bolts for a snug fit. DO NOT OVER TIGHTEN.
B
D
NOTE: The Footboard is exchangeable with Heaboard to have another bed option. Please see option as below
OPTION A OPTION B
612
/

13. Return the drawers to the storage by FOLLOW STEP BY STEP AT PAGE 11, 12.
14. For the purpose assembly, the both of Concealed metal bracket (10) were removed and put on hardware pack. At the footboard have the holes
pre-drilled, this is location of the ladder that you will install. Install the Concealed metal bracket (10) into the holes pre-drilled and secure it by Phillips
screws (11) provided. Refer to FIGURE 8.
15. Hook the ladder (J) on the footboard simultaneously align the metal concealed bracket male on the ladder with the female bracket on the footboard.
Use screw (12) provided to fix the top of ladder with footboard. as per illustration in FIGURE 9 and FIGURE 10.
10
FIGURE 9
Fig.9
12
12
No screw
No screw
FIGURE 10
712
/

16. Set the bed slats (G1, G2) on the upper bunk and lower bunk. Secure each slat by using screws (13) provided. See FIGURE 11.
17. Place the platform panels (H, I) on the lower bunk and the upper bunk, then fix them with screws (13). See FIGURE 12.
G1
G2
13
FIGURE 12
812
/

UPPER BUNK MATTRESS DIAGRAM
[5''] MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARDRAIL
[7'']
MAXIMUM
THICKNESS
PLATFORM PANEL SLAT SUPPORT
SIDE RAIL
GUARD RAIL
BEDDING SPECIFICATION:
The following size mattress and foundation are specified for use with this bunk bed.
Mattress: 53''W x 75''L x 7''H on Full upper bunk and Full lower bunk.
**Note: TOP MATTRESS AND PLATFORM MUST NOT EXCEED 7'' TOTAL THICKNESS
Be sure to adhere to these BEDDING SPECIFICATIONS in order to avoid the possibility of falling or entrapment.
THESE SPECIFICATIONS MUST BE STRICTLY ADHERED TO!
18. Align and attach the Curtain roll (K1/K2/K3) into the magnet installed on the Headboard, Footboard, Side rails and Canopies. See FIGURE 13.
19. INSTALL BEDDING
912
/

STEP #1: DRAWER REMOVAL INSTRUCTIONS
FIGURE A
Step #1.2:
Hold the drawer with both your hands. Carefully lift the drawer front up from the front metal pin, then slide drawer forward to remove from back hooks. See
FIGURE B.
Plastic
peg
FIGURE B Metal pin/
Hole for pin
Step #1.1:
Pull the drawer out. See at bottom side of drawer. Unlock the plastic peg by pulling black plastic peg
on runner out. See FIGURE A.
10 12
/