RH Baby&child 0821-79 User manual

WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
Page 1 of 12
CALLUM STORAGE BUNK BED - FULL-OVER-FULL
Made in Vietnam
Model No: 0821 - 79
Distributed in the U.S.A by:
RH Baby&Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia
V6E4N7
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Or call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools needed: Key Wrench (included).
Two people are recommended for assembly.
When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After bed is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool,
dry place and carefully package all original hardware to protect from loss.

Page 2 of 12
-
CALLUM STORAGE BUNK BED - FULL-OVER-FULL
IMPORTANT SAFETY INFORMATION FOR BUNK BED
-
1. Follow the information on the WARNINGS label appearing on the upper bunk end structure and on the
box. DO NOT REMOVE WARNING LABEL FROM BED.
2. Always use the specified mattress size, or mattress support, or both to help prevent the likelihood of
entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts.
10. Use of a nightlight may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattresses is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use with the bed, such as hooks, belts, and jump ropes.
15. Keep these instructions for future reference.
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM
ENTRAPMENT OR FALLS
1. Never allow a child under 6 years of age on upper bunk.
2. - If bunk is Twin/Twin:
Only use a mattress that is 75" long, 38" wide and 7" high on upper bunk,
and a mattress that is 75" long, 38" wide and 10" high on lower bunk.
- If bunk is Full/Full:
Only use a mattress that is 75" long, 53" wide and 7" high on upper bunk,
and a mattress that is 75" long, 53" wide and 10" high on lower bunk.
3. Ensure thickness of mattress does not exceed 7" and mattress surface is at least
5" below upper edge of guardrails. Thickness for lower bunk is 10" high.
4. Use guardrails on both sides of upper bunk.
5. Prohibit horseplay on or under bed(s).
6. Prohibit more than one person on upper bunk.
7. Use ladder for entering and leaving upper bunk.
8. If the bunk bed will be placed next to a wall, the guardrails that run the full length
of the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
STRANGULATION HAZARD
9. Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed, such as hooks, belts, and jump ropes.
DO NOT REMOVE THIS LABEL
WARNING

PARTS IDENTIFICATION
Page 3 of 12
(A) Headboard/Footboard (x2 pieces)
(D) Long Side Guard Rail (x1 piece)
(E) Short Side Guard Rail (x1 piece)
(C) Front/Back Guard Rails (x2 pieces)
(B) Ladder (x1 piece)
(G) Stretcher Bars (x4 pieces) (H) Top Platform Panels (x2 pieces)
(J) Slat Roll (x1 set)(I) Storage Box (x1 set)
(F) Bottom Side Rail (x1 piece)
CALLUM STORAGE BUNK BED - FULL-OVER-FULL

Page 4 of 12
HARDWARE INCLUDED
1
2
3
4
5
6
7
8
9
10
11
12
56 pieces
68 pieces
12 pieces
12 pieces
12 pieces
1 piece
Short Screw 8 x 19mm
Flat Washer 5/16" x 19mm
Spring Washer 5/16"x 13mm
Bolt 5/16" x 2-1/2"
Allen Key 4mm
6 pieces
4 pieces
4 pieces
4 pieces
4 pieces
1 piece
Small Metal Bracket 51 x 38 x 1.5mm
Long Metal Bracket 200 x 52 x 4mm
Medium Screw 8 x 30mm
NO. ITEM DESCRIPTIONQTY.
Threaded Rod 5/16"x 2-1/2"
Hex Nut 5/16"x 12mm
Hex Wrench 12mm
Curved Slotted Washer 5/16"
CALLUM STORAGE BUNK BED - FULL-OVER-FULL

TOOLS NEEDED
Phillips-head screwdriver (not included)
ASSEMBLY INSTRUCTIONS
Note: - Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps are finished.
Page 5 of 12
STEP 1:
Remove [3] drawers by pulling
them out of the Storage Box (I).
STEP 2:
Thread the Threaded Rod (1) into
the insert nuts of the Headboard/
Footboard (A).
CALLUM STORAGE BUNK BED - FULL-OVER-FULL

STEP 3:
Page 6 of 12
Attach the Front/Back Guard Rails (C), and Bottom
Side Rail (F), and Storage Box (I) to the Headboard/
Footboard (A) by aligning pre-installed wooden
dowels and pre-drilled holes on Back Panel with the
pre-drilled holes on the Headboard/Footboard (A).
Attach the Front/ Back Guard Rails (C), and Bottom
Side Rail (F) to the Headboard/Footboard (A) with
Curved Slotted Washer (2) and Hex Nut (3) onto
Threaded Rod (1), and tighten loosely by Wrench (5).
Attach the Storage Box (I) to the Headboard/
Footboard (A) with Flat Washer (9), Spring Washer
(10), Bolt (11), and using Allen Key (12) tighten.
Tighten all bolts at this time.
NOTE:Bunk must be assembled by
at leat 2 people. Set all parts in final
position for assembly, in a straight line.
CALLUM STORAGE BUNK BED - FULL-OVER-FULL

Page 7 of 12
Install Short Side Guard Rail (E) as indicated below.
Attach Long Metal Brackets (8) to the Short Side
Guard Rail (E) using Short Screws 8x19mm (6) that
are provided.
STEP 4:
The bunk has total of 4 orientations. Short Side Guard Rail (E) can be attached to headboard or footboard, depending on
where you would like the Ladder (B) to be positioned. Open end of Short Side Guard Rail (E) must be positioned against
Bunk Bed End (A), and closed end of Short Side Guard Rail (E) must be positioned against Ladder (B).
NOTE:
Orientation 1 Orientation 2
Orientation 3 Orientation 4
CALLUM STORAGE BUNK BED - FULL-OVER-FULL

Page 8 of 12
STEP 5:
Attach the Long Side Guard Rail (D) to the
Headboard/Footboard (A) by using Long
Metal Brackets (8) and Short Screws (6)
that are provided.
STEP 6:
Attach Small Metal Brackets (7) to top
ends of all guard rails using 8 x 19mm
Short Screws (6) that are provided.
D
7
D, E
6
CALLUM STORAGE BUNK BED - FULL-OVER-FULL

The webbing on the slats
should be on the top side.
Page 9 of 12
NOTE: If you need to move the unit, do not drag
it. 2 or more people are needed to safely move
the unit.
Lay the Stretcher Bars (G) in between the Front/
Back Guard Side Rails (C), then tighten using
Medium Screws (4) and Philips Head screwdriver.
Lay the Slat Roll (J) in between the Bottom Side
Rail (F) and Storage Box (I), use Medium Screws
(4) to fasten four end slats (two on each end) to
side rails with a screwdriver.
STEP 7:
F, I
CALLUM STORAGE BUNK BED - FULL-OVER-FULL

Page 10 of 12
Position the Ladder (B) in the opening between
the Headboard/Footboard (A) and the Short
Side Guard Rail (E). Hook the Ladder (B) over
the top and bottom side rails and tighten with
Short Screws (6) using Phillips-head screwdriver.
STEP 8:
CALLUM STORAGE BUNK BED - FULL-OVER-FULL