RH Baby&child CALLUM CRIB 355 - 130/46 User manual

CALLUM CRIB
Page 1 of 15
TODDLER KIT (SOLD SEPARATELY)
1. Read all instructions before assembly crib. Keep instructions for future use.
2. Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
3. Infants can suffocate in gaps between crib sides and a mattress that is too small.
Made in Vietnam
Model No: 355 - 130/46
Distributed in the U.S.A by:
RH Baby&Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia
V6E4N7
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Or call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools needed: Key Wrench (included).
Two people are recommended for assembly.
When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After bed is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool,
dry place and carefully package all original hardware to protect from loss.

Page 2 of 15
CALLUM CRIB
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
Strings can cause strangulation! DO NOT place items with a string around a child's neck, such as hood strings or
pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large
toys and other objects that could serve as steps for climbing out.
When child is able to climb out or reaches the height of 35 inches (89cm), the crib shall no longer be used, and
the child should be placed in a youth or regular bed.
Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly
and frequently during use. DO NOT use crib if any parts are missing, damaged or broken.
Contact customer service at 1-800-762-1751 for replacement parts and instructional literature if needed.
DO NOT substitute parts.
DO NOT use a water mattress with this crib.
If refinishing, use a non-toxic finish specified for children's products.
Follow warnings on all products in a crib.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
WARNING: Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions could result
in serious injury or death.

Page 3 of 15
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4
INCHES BY 51 5/8 INCHES WITH A THICKNESS NOT EXCEEDING
6 INCHES.
WARNING:
Do not use this crib if the enclosed or attached instructions cannot
be strictly adhered to. Do not use this crib if the child is able to climb
out unaided or is taller than 35 inches (890mm). Do not place
cords, straps or similar items that could become wound around the
child's neck in or near this crib. Ensure that the sides are properly
latched or locked in place when the crib is occupied. The mattress
used with this crib should not be more than 5 7/8 inches (150mm)
thick and should be of such length and width that the gap between
the mattress and the sides of the crib is not more than 1 3/16 inches
(30mm) when the mattress is pushed into the corner of the crib.
Parents should inspect the crib regularly before putting the child
in the crib each day and confirm that every component of the crib
is properly and securely in place.
CALLUM CRIB

Page 4 of 15
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
The mattress intended for use on the bed must be a full-size crib mattress
having minimum dimensions of 51 5/8 inches (1310mm) in length, 27 1/4
inches (690mm) in width and 4 inches (100mm) in thickness, not
exceeding 6 inches (152mm) in thickness.
If guardrails are used as the mattress containment means, guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
DO NOT place items with a string, cord, or ribbon around a child's neck,
such as hood strings or pacifier cords.
A child using the toddler or day bed must be at least 15 months of age
and must not weigh more than 50 lbs (22.7kg).
WARNING: ENTRAPMENT/STRANGULATION HAZARD
CALLUM CRIB

Page 5 of 15
PARTS INCLUDED:
A
B
C
D
HARDWARE INCLUDED:
[2]
[2]
[1]
[2]
HEADBOARD/FOOTBOARD
STATIONARY SIDE RAILS
MATTRESS SUPPORT
STRETCHER BARS
BA
A
C
B
D
1
2
3
4
5
6
Long Bolts 5/16”x 2-1/2”4 pcs.
Medium Bolts 5/16” x 50mm
Mattress Bolts 6 x 32mm
8 pcs.
12 pcs.
12 pcs.
Hex Nut 6 x 10mm
Cap Hex Nut 6mm
16 pcs.
NO. ITEM DESCRIPTIONQTY.
Half Moon Washer 4 pcs.
CALLUM CRIB

ASSEMBLY INSTRUCTIONS
Note: - Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the above parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps are finished.
Page 6 of 15
4 pcs.
4 pcs.
4 pcs.
NO. ITEM DESCRIPTIONQTY.
7
8
9
10
12
11
Allen Key 4mm 1 pc.
Mattress Bolts 6 x 40mm
2 pcs.
Short Bolts 5/16” x 3/4”
Spring Washer 1/4” x 10mm
Flat Washer 1/4” x 16mm
1 pc.
Multi Wrench 10mm
10mm
CALLUM CRIB

Page 7 of 15
STEP 1:
Note: The Mattress Support (C)
should be at the highest level
when the child is born.
It must be at the lowest level
before the child can stand up.
Before installing the Mattress
Support (C), determine the
desired height of the mattress.
C
Attach scissor assembly bars to
the Mattress Support (C) using
Mattress Bolts (4), Hex Nut (5)
and Cap Nut (6). Tighten with
Allen Key (7) and Hex Wrench (8).
Next, insert Mattress Bolts (4) into
the upper holes of the Mattress
Support (C) using Hex Nut (5) and
Cap Nut (6). Tighten with Allen
Key (7) and Hex Wrench (8).
74
58
6
Highest level
Lowest level
Middle level
5
74
6
8
CALLUM CRIB

Page 8 of 15
STEP 2:
Attach the Stretcher Bars (D) into the
Headboard/Footboard (A) using Long
Bolts (1), Half Moon Washer (2) and
tighten with Allen Key (7).
DA
7
1
2
A
D
A
D
D
CALLUM CRIB

Page 9 of 15
STEP 3:
Attach the Mattress Support (C) to
the Stretcher Bars (D) using Mattress
Bolts (9), Spring Washer (11) Flat
Washer (12), Hex Nut (5), and tighten
with Allen Key (7) and Hex Wrench (8).
STEP 4:
Lay the Stationary Side Rails (B) in
between the Headboard/Footboard (A).
D
B
C
D
B
12
9
7
11 5
8
CALLUM CRIB

STEP 5:
Attach the Stationary Side Rail (B)
to the Headboard/Footboard (A) by
using Medium Bolts (3) and tighten
with Allen Key (7).
Page 10 of 15
After crib is completely assembled,
return to each bolt and tighten to
snug fit. DO NOT over tighten.
WARNING:
73
CALLUM CRIB

Page 11 of 15
PARTS INCLUDED:
E
[1] TODDLER RAIL
HARDWARE INCLUDED:
NO. ITEM DESCRIPTIONQTY.
Medium Bolts 5/16” x 50mm 4 pcs.
Allen Key 4mm 1 pc.
2 pcs. Short Bolts 5/16” x 3/4”
13
14
15
E
CALLUM CRIB

Page 12 of 15
STEP 6:
Unscrew and remove the 4 bolts on the
stationary side rail using Allen Key (14).
Then carefully remove stationary side
rail from the crib
14
3
B
CALLUM CRIB

Page 13 of 15
STEP 7:
Highest level
Lowest level
Middle level
If the mattress support is not in the lowest position,
unscrew and remove all the tightened bolts from
scissor assembly bars to the Mattress Support (C)
and move it to the lowest position.
Note: The Mattress Support (C) must be at the
lowest level for a toddler bed.
C
CALLUM CRIB

Page 14 of 15
STEP 8:
STEP 9:
Position the Toddler Rail (E) between
the Headboard/Footboard (A).
A
E
A
Attach the Toddler Rail (E) to the
Headboard/Footboard (A) by using
Medium Bolts (13) and tighten with
Allen Key (14).
14
13
CALLUM CRIB

Page 15 of 15
STEP 10:
When converting the crib to toddler
bed, the Short Bolts (15) should be
inserted in the upper holes of the
Headboard/Footboard (A), and
tightened with the Allen Key (14).
14
15
CALLUM CRIB
After crib is completely assembled,
return to each bolt and tighten to
snug fit.
DO NOT over tighten.
WARNING:
CARE INSTRUCTIONS:
1. DUST OFTEN USING A CLEAN, SOFT, DRY LINT- FREE CLOTH.
2. BLOT SPILLS IMMEDIATELY AND WIPE WITH A CLEAN, DAMP CLOTH.
3. DO NOT USE CHEMICAL CLEANSERS, ABRASIVES OR FURNITURE POLISH ON THE LACQUERED FINISH.