RH Baby&child Wyler Crib User manual

11
/
1/9

IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
·To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
·DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
·When child is able to climb out or reaches the height of 35" (89cm), the crib shall no longer be used,
and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT
use crib if any parts are missing, damaged or broken. Contact customer service at 1-800-762-1751
for replacement parts and instructional literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.
2/9

IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB SHALL BE
AT LEAST 27 1/4" X 51 5/8" WITH A THICKNESS
NOT EXCEEDING 6".
WARNING
Do not use this crib if you cannot exactly follow the instructions
provided.
Do not use this crib for a child who can climb out of it or who is
taller than 35" (89cm).
Do not place in or near the crib any cord, strap or similar item that
could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and the strangled.
Check this crib regularly before using it, and do not use if any part
is loose or missing or if there are any signs of damage.
Do not substitute parts. Contact the manufacturer if replacement
parts or additional instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no thicker than 15cm in height and, when it
is pushed firmly against any side of this crib, it does not leave a
gap of more than 3cm between the mattress and any part of any
other side of the crib.
3/9

IMPORTANT SAFETY INFORMATION FOR TODDLER AND DAYBEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51 5/8" (1310mm) in
length, 27 1/4" (690mm) in width and 4" (100mm) in thickness, not
exceeding 6" (150mm) in thickness.
·DO NOT place bed near windows where cords from blinds or
drapes may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or daybed shall be at least 15 months of
age and shall not weigh more than 50 lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months of age.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
4/9

ITEM IDENTIFICATION
For ease of identification, all parts are labeled to correspond
to the Step number in which the part is used.
Step #1 First side rail and end panel assembly (Page 6)
Step #2 Mattress Support Arm assembly
Stabilizer Rail assembly
Mattress height adjustment (Page 7)
Step #3 Installation of Stabilizer Rail into the end panels (Page 8)
Step #4 Second side rail assembly (Page 9)
SIDE RAIL
END PANEL
MATTRESS SUPPORT
5/9

STEP #1
1ST SIDE RAIL & END PANEL ASSEMBLY
Attach the the first side rail to the end panels by using
Allen bolts (AA) with the lock washers and plain washers.
Please see DETAIL A.
HARDWARE NEEDED FOR STEP #1:
Allen Wrench = 1pc
Lock Washers 1/4" = 4 pcs
Plain Washers 1/4" = 4 pcs
(AA) 1/4" x 1-3/4" BOLT = 4 pcs
DETAIL A
(AA)
6/9

Lock washer
DETAIL B
Hexagon nut
Plain washer
Mattress bolt
Allen wrench
HARDWARE FOR STEP #2:
(BB) 1/4" X 1-1/4" BOLT = 8 PCS Hexagonal nut = 8 pcs
STEP #2
MATTRESS SUPPORT ARM ASSEMBLY
STABILIZER RAIL ASSEMBLY MATTRESS
HEIGHT ADJUSTMENT
Open wrench = 1 pc
Allen wrench = 1 pc
DETAIL C
Hexagon nut
Lock washer
Plain washer
(BB)
STEP #2.1
Lay Mattress Support flat with Stabilizer Rail on each side
Note:
On each end of the arm of the Mattress Support, there is a hole for the
bolt to pass through that corresponds to the holes located in the frame of
the Mattress Support.
STEP #2.2:
Insert the bolt into the desired hole of the frame through the hole on the
arm support. Fasten the bolt with plain washer, lock washers &
hexagonal nut provided. Repeat procedure on other arms of the
Mattress Support. Please see DETAIL B.
WARNING:
Set the Mattress Support to the desired height by adjusting the Support
Arms. The Mattress Support should be at its highest setting for
newborns, then adjusted to the lower positions as the child grows and
becomes mobile. Once the child is able to stand, the Mattress Support
should be at its lowest position.
STEP #2.3:
Install the Stabilizer Rail at ends of the arm support, as illustrated on
DETAIL C.
Lock Washers 1/4" = 8 pcs
Plain Washers 1/4" = 8 pcs
7/9

DETAIL D
HARDWARE FOR STEP #3:
STEP #3
INSTALLATION OF STABILIZER RAILS
INTO THE END PANELS
(CC) 1/4" X 13/16 " BOLT = 4 pcs
DETAIL E
Allen Wrench = 1 pc
(CC)
STEP #3.1
On inside surface of both end panels are pre-installed
metal brackets, designed to hold the Stabilizer Rails. Set
both ends of the Stabilizer Rails into brackets, as
illustrated in DETAIL D.
STEP #3.2
Gently lay down the crib then fasten the Stabilizer Rails
with bolts (CC), plain washers and lock washers
provided, as illustrated in DETAIL E.
Lock Washers 1/4" = 4 pcs
Plain Washers 1/4" = 4 pcs
8/9

STEP #4
SECOND SIDE RAIL ASSEMBLY
Allen Wrench = 1 pc
DETAIL F
(AA) 1/4" x 1-3/4"
BOLT = 8 pcs
Lock Washers 1/4" = 8 pcs
Plain Washers 1/4" = 8 pcs
(AA)
Lock washer
Plain washer
HARDWARE NEEDED FOR STEP #4:
Attach the second side rail to the end panels by using Allen bolts (AA), lock washers and plain washers.
Please see DETAIL F.
After assembly, re-tighten all bolts to a snug fit. DO NOT OVER TIGHTEN.
9/9