RH Baby&child BELLINA STORAGE CONVERSION CRIB User manual

11
/
1/11

IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
·To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
·DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
·When child is able to climb out or reaches the height of 35" (89cm), the crib shall no longer be used,
and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT
use crib if any parts are missing, damaged or broken. Contact customer service at 1-800-762-1751
for replacement parts and instructional literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.
2/11

IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB SHALL BE
AT LEAST 27 1/4" X 51 5/8" WITH A THICKNESS
NOT EXCEEDING 6".
WARNING
Do not use this crib if you cannot exactly follow the instructions
provided.
Do not use this crib for a child who can climb out of it or who is
taller than 35" (89cm).
Do not place in or near the crib any cord, strap or similar item that
could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and the strangled.
Check this crib regularly before using it, and do not use if any part
is loose or missing or if there are any signs of damage.
Do not substitute parts. Contact the manufacturer if replacement
parts or additional instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no thicker than 15cm in height and, when it
is pushed firmly against any side of this crib, it does not leave a
gap of more than 3cm between the mattress and any part of any
other side of the crib.
3/11

IMPORTANT SAFETY INFORMATION FOR TODDLER AND DAYBEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51 5/8" (1310mm) in
length, 27 1/4" (690mm) in width and 4" (100mm) in thickness, not
exceeding 6" (152mm) in thickness.
·DO NOT place bed near windows where cords from blinds or
drapes may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or daybed shall be at least 15 months of
age and shall not weigh more than 50 lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months of age.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
4/11

PARTS IDENTIFICATION
For ease of identification, all parts are labeled to correspond to the step number in which
the part is used.
Step 1 Attaching legs to headboard and side rail panels
Side rail panels and storage assembly (Page 6)
Step 2 Mattress support assembly (Page 7)
Step 3 Headboard assembly (Page 8)
Step 4 Front rail assembly and covering unused holes (Page 9)
Step 5 Toddler rail assembly (Page 10)
Step 6 Metal bed frame assembly (Page 11)
HEADBOARD SIDE RAIL PANEL
(RIGHT)
FRONT RAIL
STORAGE
MATTRESS SUPPORT
SIDE RAIL PANEL
(LEFT)
LEGS
5/11
DECORATIVE WOOD CAPS
TODDLER RAIL
(SOLD SEPARATELY)

STEP 1
ATTACHING LEGS TO HEADBOARD AND SIDE RAILS
SIDE RAIL PANELS AND STORAGE ASSEMBLY
STEP 1.1
Gently lay the headboard and side rails on a clean,
non-abrasive surface.
STEP 1.2
Align and insert the threaded rods of the legs into
the holes on the bottom of the headboard and side
rails. Turn clockwise to tighten. See DETAIL A.
STEP 1.3
Remove the drawers from the storage spaces.
STEP 1.4
Bring the storage and the side rail panels to an
upright position. Align the locator pins on both ends
of the storage to the bore holes in the side rail
panels. Refer to DETAIL B and DETAIL C.
STEP 1.5
Attach the side panels to the storage by using Allen
bolts (BB) together with lock washers and plain
washers. See DETAIL B and DETAIL C.
HARDWARE NEEDED FOR STEP 1:
Allen Wrench = 1 pc.
(BB)1/4" x 1 3/4" Allen Bolt = 8 pcs.
Lock Washers 1/4" = 8 pcs.
Plain Washers 1/4" = 8 pcs.
B
C
DETAIL A
(BB)
(BB)
DETAIL B
DETAIL C
6/11

STEP 2
MATTRESS SUPPORT ASSEMBLY
STEP 2.1
Attach the support arms to the mattress support using Allen bolts
(CC), lock washers and plain washers. See DETAIL D.
STEP 2.2
Hang the mattress support on both side panels by using Allen
bolts (CC), lock washers and plain washers to attach the support
arms into the fixed nuts in the side vertical rails of the side panels.
See DETAIL E.
WARNING:
Set the mattress support to the desired height by adjusting the
support arms. The mattress support should be at its highest
setting for newborns, then adjusted to the lower positions as the
child grows and becomes mobile. Once the child is able to stand,
the mattress support should be at its lowest position.
HARDWARE NEEDED FOR STEP 2:
(CC) 1/4" x 13/16 " Allen Bolt = 8 pcs.
Lock Washer 1/4" = 8 pcs.
Plain Washer 1/4" = 8 pcs.
Allen Wrench = 1 pc.
Support Arm = 4 pcs.
D
Support Arm
(CC)
DETAIL D
(BB)
E
DETAIL E
7/11

STEP 3
HEADBOARD ASSEMBLY
STEP 3.1
Hold the headboard to the back sides of the side
panels.
STEP 3.2
Use Allen bolts (AA) and (BB), lock washers and
plain washers to attach the crib headboard to the
side panels. See DETAIL F and DETAIL G.
HARDWARE NEEDED FOR STEP 3:
(AA) 1/4" x 2 3/16" Allen Bolt = 2 pcs.
Lock Washers 1/4" = 4 pcs.
Plain Washers 1/4" = 4 pcs. Allen Wrench = 1 pc.
(BB) 1/4" x 1 3/4" Allen Bolt = 2 pcs.
F
G
(BB)
(AA)
Unused
DETAIL F
DETAIL G
8/11

STEP 4
FRONT RAIL ASSEMBLY AND COVERING UNUSED HOLES
STEP 4.1
Both ends of the front rail have holes for the bolt to pass through
that correspond to the holes on the posts for both side rail panels
with pre-installed nuts. Attach the front rail frame to the side rail
panels by using Allen bolts (AA) with lock washers and plain
washers. See DETAIL H.
After assembly, re-tighten all bolts for a snug fit. DO NOT OVER
TIGHTEN.
STEP 4.2
Return the drawers to the storage spaces.
STEP 4.3
When the mattress support is on the middle or lowest setting,
unused holes can hurt your child's fingers. Use the Allen bolts
provided to hide these holes. See illustration in DETAIL I.
HARDWARE NEEDED FOR STEP 4:
(AA) 1/4" x 2 3/16 " Allen Bolt = 4 pcs.
Lock Washers 1/4" = 4 pcs. Plain Washers 1/4" = 4 pcs. Allen Wrench = 1 pc.
(DD) 1/4" x 1/2" Allen Bolt = 8 pcs.
(DD)
DETAIL I
IH
(AA)
DETAIL H
9/11

STEP 5
TODDLER RAIL ASSEMBLY
STEP 5.1
Loose all the bolts in both ends of the front side rail to disassemble it.
STEP 5.2
Slightly loosen the bolt at the back of the headboard just enough to set
the toddler rail in between the side rails.
STEP 5.3
Inside each side rail is a cavity for the hook that corresponds to the
hook on both ends of the toddler rail. Align and insert the hook of the
toddler rail into the cavity of the side rails as shown in DETAIL J.
NOTE: If mattress support is not in the lowest position, unscrew
mattress support bolts and move the lowest position.
STEP 5.4:
The unused holes can hurt your child's fingers. Use the Allen bolts (EE)
provided (packed inside toddler rail box) to hide these holes.
See DETAIL K.
Allen Wrench = 1 pc.
(EE) 1/4" x 1/2" Allen Bolt = 2 pcs.
HARDWARE FOR STEP 5:
(PACKED INSIDE TODDLER RAIL BOX)
J
K
DETAIL J
(EE)
DETAIL K
10/11

DETAIL L
11/11
HARDWARE NEEDED FOR STEP 6
(FF) M6 x 40mm Allen Bolt = 4 pcs
Lock Washers = 4 pcs
Plain Washers = 4 pcs
Allen Wrench = 2 pcs
Sleeve Nut M6 = 4 pcs
DETAIL M
Allen Wrench = 1 pc
(AA) 1/4" x 1-3/4" Allen Bolt = 2 pcs
Lock Washers = 2 pcs
Plain Washers = 2 pcs
(AA)
STEP 6
METAL BED FRAME ASSEMBLY
STEP 6.1
Loose all the bolts in crib to
disassemble the crib.
STEP 6.2
Bring the heaboard to the upright
position.
STEP 6.3
On the bottom of the headboard there
are holes for the bolt to pass through
that correspond to the holes on the
metal bed frame. Attach the metal bed
frame to the headboard by using allen
bolts (FF) with lock washers and plain
washers into the sleeve nut on the
other side. See DETAIL L.
STEP 6.4
Fill the holes located on the top of the side
rail panel by attaching the decorative wood
caps with Allen bolt (AA). ( DETAIL M )
M
L
(FF)