RH Baby&child ARLO PANEL H0039- 6 User manual

Made in Vietnam
Distributed in the U.S.A by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
All Restoration Hardware cribs are designed to meet the highest safety
standards and comply with all U.S. and Canadian cribs and cradles regulations.
Model No: H0039 - 6
ARLO PANEL TODDLER KIT
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
Page 1 of 6
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool
dry place and carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included).
NOTE: It may be easier to assemble productwith two people.
NOTE:When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After crib is completely assembled,
return to each bolt and tighten.

IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could result in
serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes may strangle
a child.
The mattress intended for use on the bed shall be a full-size crib mattress
having minimum dimensions of 51 5/8 inches (1310 mm) in length, 271/4
inches (690 mm) in width and 4 inches (100 mm) in thickness, not
exceeding 6 inches (152 mm) in thickness.
If guardrails are used as the mattress containment means, guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
DO NOT place items with a string, cord, or ribbon around a child's neck,
such as hood strings or pacifier cords.
A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50 lbs (22.7 kg).
WARNING: ENTRAPMENT/ STRANGULATION HAZARD
Page 2 of 6

ASSEMBLY INSTRUCTIONS
Page 3 of 6
PARTS INCLUDED:
E [1] TODDLER RAIL
CRIB ( Sold separately)
E
HARDWARE INCLUDED:
7
8
9
10
11
Short Bolts 5/16” x 1-3/4” 4 pcs.
Long Bolts 1/4” x 2-1/4” 2 pcs.
Spring Washer 5/16” 6 pcs.
NO. ITEM DESCRIPTIONQTY.
Allen Key 4mm 1 pc.
Small Bolts 5/16” x 3/4” 2 pcs.

Carefully unscrewing and removing
the (2pcs) long bolts from the bottom of
the Metal Leg frame (D), and (4pcs) short
bolts with spring washer on left /right
sides of the Stationary Side Rail (B) using
Allen Key (11).
Page 4 of 6
STEP 1:
Remove Stationary Side Rail (B) from the
crib.
STEP 2:
D
B
D
ASSEMBLY INSTRUCTIONS
2x
11
11
4x
B

Page 5 of 6
If mattress support is not in the lowest
position, loosen all tightened bolts from
side frames. Spread front of crib open
enough to remove mattre ss support (C),
and move it to the lowest position.
STEP 3:
4x
A
Highest
level
Note: The M attress support ( C) mus t be at
the l owest l evel for a toddler bed.
Middle
level
Lowest
level
C
11
C
ASSEMB LY INSTRUCT IONS
STEP 4:
Position the Toddler Rail (E) between the
Headboard/ Footboard (A) and align the holes.
E
E
E
A
A
A
Attachthe Toddler Rail (E) to the crib by
securi n g w ith Short Bolts (7), Spring Washers
(9), and tighten with Allen Key (11).
DO NOT FULLY TIGHTEN AT THIS TIME.
7
11
9
4x

Page 6 of 6
STEP 6:
When converting the crib to toddler bed, the
Small Bolt (10), and Spring Washer (9) should
be inserted in the upper holes of the Side
Frame (A) and tighten with the Allen Key (11).
STEP 5:
After crib is completely assembled, return to each
bolt and tighten to snug fit. DO NOT over tighten.
WARNING:
A
2x
9
11
10
ASSEMBLY INSTRUCTIONS
D
D
E
E
8
A
A
11
2x
Attach the Metal Leg Frame (D) to the Toddler
Rail (E) with Long Bolt (8), and tighten using
Allen Key (11).