RH Baby&child AVALON STORAGE TODDLER BED User manual

11
/
1/5

2/5
IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51-5/8 inches (1310mm) in
length, 27-1/4 inches (690mm) in width and 4 inches (100 mm) in
thickness, not exceeding 6 inches (152 mm) in thickness.
·If guardrails are used as the mattress containment means,
guardrail(s) provided must be used to avoid the formation of a gap
between the mattress and the bed that could cause an entrapment.
·DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.

WARNING: ADULT ASSEMBLY ONLY, OWING TO THE PRESENCE OF
SMALL PARTS, SHARP POINTS AND EDGES.
CAUTION
TODDLER BED: THE MINIMUM AGE SHALL NOT BE LESS THAN 15 MONTHS AND THE MAXIMUM
WEIGHT SHALL NOT BE GREATER THAN 50LBS. (22.7 KG).
THE MATTRESS INTENDED FOR USE ON THE BED SHALL BE A FULL-SIZE CRIB MATTRESS HAVING
MINIMUM DIMENSIONS OF 51-5/8 IN. (1310MM) IN LENGTH, 27-1/4 IN(690MM)IN WIDTH AND 4 IN. (100MM)
IN THICKNESS NOT EXCEEDING 6 IN. (152MM) IN THICKNESS.
CARE INSTRUCTIONS:
• Dust often using a clean, soft, dry, lint- free cloth.
• Blot spills immediately, and wipe with a clean, damp cloth.
• We do not recommend the use of chemical cleaners, abrasives, or furniture polish on our lacquered finish.
TODDLER CONVERSION KIT
ASSEMBLY HARDWARE IS
INCLUDED IN THE TODDLER
KIT BOX.
SIDE RAIL
END PANEL
TODDLER BED
CONVERSION KIT
STORAGE
MATTRESS SUPPORT
3/5

ASSEMBLY INSTRUCTIONS
STEP #1:
Loosen all the bolts on both ends of the front side rail to
disassemble the front side rail.
STEP #2:
Replace the front side rail with the toddler rail. See DETAIL A.
After assembly, re-tighten all bolts for a snug fit. DO NOT OVER
TIGHTEN.
HARDWARE NEEDED FOR STEP #1 & #2:
(REMOVED FROM THE SIDE RAIL)
Lock Washers 1/4" = 4 pcs
Plain Washers 1/4" = 4 pcs Allen Wrench = 1pc
(CC) 1/4" x 1-3/4" BOLT = 4 pcs
DETAIL A
(CC)
OPTION USE THE BED WITH TWO
TODDLER RAILS:
Repeat STEP #1-#2 above procedure
4/5

STEP #3
HIDE UNUSED HOLES
Unused holes can hurt your child's fingers. Please use Allen bolts (EE) provided to hide these holes. See illustration in Detail B.
HARDWARE NEEDED FOR STEP #3:
Allen Wrench = 1pc
(EE) 1/4" x 1/2" BOLT = 2 pcs
DETAIL B
(EE)
5/5