Riccar RAPL User manual

Description of the vacuum
R APL & R APM
O w n e r ’ s M a n u a l
by
RI-FB_Manual_4.06.indd 1 5/1/06 7:19:15 PM

1
IMPORTANT SAFETY INSTRUCTIONS .............................................................. 2
Product specifications ...................................................................................... 3
Description of the air cleaner ............................................................................ 4
Operation
Air cleaner setup .............................................................................................. 6
Display panel .................................................................................................... 7
Automatic, manual and turbo fan speeds ......................................................... 8
Plasma, timer and auto sleep ............................................................................ 9
Odor and dust sensors .................................................................................... 10
Remote control ................................................................................................ 11
Maintenance and Care
Cleaning unit .................................................................................................... 14
Filter changing .................................................................................................. 15
Filter cleaning ................................................................................................... 16
Dust sensor cleaning ........................................................................................ 18
Problem Solving Guide
Troubleshooting ................................................................................................ 19
How to contact your Authorized Retailer .......................................................... 19
Visit Riccar on-line ............................................................................................ 19
Warranty ................................................................................................................. 20
Owner’s warranty information ........................................................................... 21
Contents
RI-FB_Manual_4.06.indd 2-1 5/1/06 7:19:15 PM

2
3
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including
the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE
The manufacturer cannot accept responsibility for damage
caused when the appliance is not used according to the
instructions, or for uses other than those for which it
was intended.
To reduce the risk of fire, electric shock or injury:
• Do not repair or modify the unit unless
specifically recommended in this manual.
All other repairs should be completed by a
qualified technician.
• The plug for this unit is polarized with one
blade wider than the other. Do not force the
plug into an electrical outlet.
• Do not alter the plug in any way. If the plug
does not fit into the outlet, reverse the plug.
If it still does not fit, contact a qualified
technician to install a proper outlet.
• Do not use if the power cord or plug is
damaged or the connection to the wall
outlet is loose.
• Use AC 120V only.
• Do not damage, break, forcefully bend,
pull, twist, bundle, coat, pinch, or place
heavy objects on the power cord.
• Periodically remove dust from the power
plug. This will reduce the chance that
humidity will accumulate, which increases
the risk of electric shock.
• If the power plug is damaged, it must be
replaced by the manufacturer or a qualified
technician.
• Remove the power plug from the outlet
before cleaning the unit. When removing
the power plug, grasp by holding the plug
itself, never hold by the cord.
• Remove the power plug from the outlet
when the unit is not in use.
• Do not handle the power plug with wet
hands.
• Do not operate the unit when using indoor
smoke-generating insecticides.
• Do not clean unit with benzene or paint
thinner. Do not spray insecticides on the
unit.
• Do not use the unit where it is humid or
where the unit may get wet, such as in a
bathroom.
• Do not insert fingers or foreign objects into
the air intake or outlet.
• Do not use the unit near flammable gases.
Do not use near cigarettes, incense, or
other spark-creating items.
• Unit will not remove carbon monoxide
emitted from heating appliances or other
sources.
• Do not block the intake or outlet vents.
• Do not use near hot objects, such as a
stove. Do not use where the unit may come
into contact with steam.
• Do not use the unit on its side.
• Keep away from products that generate
oily residue, such as a deep fryer.
• Do not use detergent to clean the unit.
• Do not operate without a filter.
• Do not wash and reuse the HEPA Filter.
SAVE THESE INSTRUCTIONS.
WARNING:
Product Specifications
RAPL RAPM
Room Area Served 280 sq. ft. 210 sq. ft.
Power Supply AC 120V/60(Hz) AC 120V/60(Hz)
Power Rate Low 6W, Turbo 50W Low 6W, Turbo 50W
Fan Speed 4 Speeds 4 Speeds
Display LED Digital LED Digital
Control Type Auto/Manual Auto/Manual
Dust Sensor Yes Yes
Odor Sensor Yes Yes
Light Sensor Yes Yes
Timer 1, 4 and 8 hour(s) 1, 4 and 8 hour(s)
Sleep Mode Yes Yes
Filters 1 Replaceable Cassette 1 Replaceable Cassette
Cleaning System
Washable Anti-Bacterial Pre-Filter
HEPA Filter
Washable Nano-Silver
Mesh/Carbon Filter
PlasmaWave
Washable Anti-Bacterial Pre-Filter
HEPA Filter
Washable Nano-Silver
Mesh/Carbon Filter
PlasmaWave
CADR 182/183/194
(Smoke/Dust/Pollen)
142/138/145
(Smoke/Dust/Pollen)
HEPA Filter HEPA 99.99% HEPA 99.99%
Technology PlasmaWave PlasmaWave
Color Metallic Silver Metallic Blue
Remote Control Yes Yes
Dimensions 16.5”(W) X 9.9”(D) X 21.9”(H) 13.8”(W) X 9.1”(D) X 18.5”(H)
Weight 18.8 lbs 13.7 lbs
RI-FB_Manual_4.06.indd 2-3 5/1/06 7:19:16 PM

4
5
Description of the air cleaner
1
Front Side
Top Side
1 PlasmaWave™
2 Display Panel
3 DC Motor
4 Washable Nano-Silver Mesh/Carbon Filter
5 Cassette Frame
6 HEPA Filter
7 Pre-Filter
8 Front Panel
9 Power Plug
10 Air Outlet
11 Remote Control Cradle
Description of the air cleaner
Five-stage Cleaning
Air undergoes five separate processes before returning,
freshened and cleaned, to the room.
Stage 1 Washable Anti-Bacterial Pre-Filter (#7)
This reusable filter collects large particles, pollen,
pet hair, lint, etc.
Stage 2 HEPA Filter (#6)
Captures 99.99% of particles and impurities as small
as .3 microns.
Stage 3 Nano-Silver Mesh (#4)
A shield of silver particles one billionth of a meter in
size neutralizes bacteria on contact.
Stage 4 Washable Carbon Filter (#4)
This reusable activated granular carbon effectively collects
chemical vapors and odors caused by cigarette smoke,
organic decay and cooking.
Stage 5 PlasmaWave (#1)
In the final stage of cleaning, PlasmaWave technology generates
both positive and negative ions to create plasma clusters which
instantly neutralize viruses, bacteria, chemical vapors and odors
in the air.
RI-FB_Manual_4.06.indd 4-5 5/1/06 7:19:17 PM

6
7
Operation Operation
Note: Follow these instructions for best results.
• Place unit at least 7 feet from equipment that
emits electric waves such as televisions or radios.
• Place unit at least 2 feet from the wall.
• Keep sensors away from drafty areas.
• Keep curtains away from sensors, as they may
interfere with air intake/outlet.
• Place unit on a stable surface with plenty of air
circulation.
To set-up cleaner:
• Remove protective film from the control panel.
• Remove the front panel by grasping the bottom
outside edges and gently pulling toward you.
• Pull out the filter cassette by grasping the tabs
located on each side of the filter cassette.
• Remove the plastic wrap from the filter cassette.
• Return the filter cassette into the main unit.
• Replace the front panel by hooking the front panel
on the top of the unit. Swing panel in by pushing
gently until the panel snaps into place.
• Plug in the power cord to a wall outlet.
• Press power button until short “beep” is heard.
Note: For the first 4 minutes after turning the unit
on, the dust and odor indicators will flash while
the unit measures air quality.
1. Timer - Press the TIMER button once
for 1 hour of operation; press the button
a second time for 4 hours; press a third
time for 8 hours. Pressing the TIMER
button a fourth time returns to the Off
Timer mode.
2. Function - Press the FUNCTION button
once to set the unit to Auto. Continue
to press the button for Sleep > Low >
Medium > High > Return to Auto.
3. Dust & Odor Sensors - Automatically
monitor air quality and adjust fan speed.
4. Change Filter Indicator - The
indicator will signal when to replace the
filter cassette.
5. Auto Mode - The unit is set to
default to Automatic operation when
it is first turned on. Smart sensors will
automatically sense the amount of
impurities in the air, and adjust the fan
speed accordingly.
6. PlasmaWave Indicator - Turn on
the Plasma generator by pressing
the PLASMA ON/OFF button on the
remote. PlasmaWave generates both
positive and negative ions to produce
hydroxyl radicals that inactivate airborn
contaminants.
7
. Light Sensor - Automatically activates
Sleep mode when room is darkened.
8. Fan Speed Indicator - Shows current
fan speed setting.
9. Sleep - The unit will work on Ultra-Quiet
mode and dim the control panel lights.
10. Auto Sleep Mode - Use the TIMER
button on the display or remote to
manually turn the light sensor on or off.
With the light sensor on, the unit will
automatically operate in Sleep mode
when the room is dark. When the
room is light, the unit will revert to its
previous settings. Sleep mode provides
the lowest, quietest fan setting and a
dimmed display panel.
11. Timer - Indicates timer setting or
continuous mode.
12.Power Button - Turn unit on and off by
pressing the POWER button. Holding
the button down for 2-3 seconds turns
the Plasma generator on or off.
1
2
3 3
5
6
8
9
11
12
4
7 10
Display Panel
RI-FB_Manual_4.06.indd 6-7 5/1/06 7:19:24 PM

8
9
Operation Operation
Automatic
The unit is set to default to Automatic
operation when it is first turned on. The air
cleaner will automatically sense the amount
of impurities in the air, and adjust the fan
speed accordingly.
Manual
After you turn on the unit, you can switch
to manual operation by using the remote
control or the Function button on the unit.
Low, Medium, and High
• These levels are recommended for
standard daytime use. HIGH will activate
automatically when sensors detect high
levels of dust or odors.
Turbo
• The Turbo level, the highest fan speed,
can be activated manually for maximum
air circulation.
Plasma on/off
Activate PlasmaWave by depressing for 2-3
seconds the Plasma ON/OFF button on the
remote, or the POWER button on the unit.
PlasmaWave generates positive and negative
ions.
Timer
Set the timer for 1, 4, or 8 hours by pressing
the Timer button on the remote or the unit.
The unit will stop operating when the set time
is up. Cancel the timer by pressing the Timer
button until the 1-, 4-, and 8-hour indicator
light on the unit disappears.
Auto Sleep
Use the TIMER button on the display or
remote to manually turn the light sensor on or
off. With the light sensor on, the unit will au-
tomatically operate in Sleep mode when the
room is dark. When the room is light, the unit
will revert to its previous settings. Sleep mode
provides the lowest, quietest fan setting and a
dimmed display panel.
Part Is Blinking
Low
Medium
High
Turbo
RI-FB_Manual_4.06.indd 8-9 5/1/06 7:19:27 PM

10
11
Odor Sensor
The odor sensor responds to cigarette
smoke and pet odors, as well as other
air contaminants such as insecticides,
cosmetics, alcohol or aerosol sprays.
Dust Sensor
The dust sensor detects particles in the air
such as cigarette smoke, dust and pollen.
Operation Operation
Low
Low High
Medium
Indoor Dust Volume
High
Medium
Indoor Odor Volume
Remote Control
Preparation
• Press and slide the back cover of the
remote to remove.
• Insert batteries as shown.
• Close the back cover.
Battery Use
• The batteries for the remote control
are for initial use only. Change the
batteries when necessary.
• When replacing the batteries, replace
both at once with 2 new AA batteries.
• Incorrect battery usage may cause
battery fluid leakage and/or damage.
• When not using the remote control for
an extended period of time, remove
the batteries.
• Avoid dropping or damaging the
remote control. Keep remote control
away from direct sunlight or heaters.
RI-FB_Manual_4.06.indd 10-11 5/1/06 7:19:28 PM

12
13
Operation Operation
Using the Remote Control
Proper conditions
• Operate the remote control facing the air
cleaner.
• Operate within 20 feet of the air cleaner.
Poor conditions that may
impair operation
• Any location where there is inverter
lighting equipment or electronic
spontaneous lighting equipment.
• When objects or furniture are located
between remote and air cleaner.
• When air cleaner unit is located in direct
sunlight.
• In areas where fluorescent lighting is
flickering due to worn out bulbs.
Power
• Use the power button to turn the power
on and off. A short “beep” will sound
when you turn the unit on or off. Once
the unit is on, it will automatically switch
into Automatic operation. Turn the unit
to manual control by pressing one of the
FAN CONTROL buttons.
Timer
• This button is used to set the timer. Press
the button repeatedly to set the unit to
run for 1, 4, or 8 hours, or to cancel. Each
time you press the button, it will advance
to the next pre-set amount of time. The
indicator light on the unit will show the
remaining amount of time. The unit will
stop operating when the set amount of
time runs out.
Fan Control
Up Use this button to switch from
Automatic operation and increase
the fan speed level.
Down Use this button to decrease the
fan speed level.
Turbo
• Use this button to switch from Automatic
operation and begin the maximum
amount of room cleaning and air
movement.
Auto Sleep
• Use the TIMER button to manually turn
the light sensor on or off. With the light
sensor on, the unit will automatically
operate in Sleep mode when the room is
dark. When the room is light, the unit will
revert to its previous settings. Sleep mode
provides the lowest, quietest fan setting
and a dimmed display panel.
Plasma On/off
• Use this button to turn the PlasmaWave
generator on or off.
POWER button
AUTO button
TIMER button
TURBO button
PLASMAWAVE
ON/OFF button
FAN CONTROL buttons
SLEEP button
AUTO SLEEP
button
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference through one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.
• Consult an experienced radio/TV technician for help.
RI-FB_Manual_4.06.indd 12-13 5/1/06 7:19:29 PM

14
15
Cleaning
• Clean unit as necessary by wiping with a dry,
soft cloth; for stubborn stains, use a warm, damp
cloth.
• Do not use volatile fluids such as benzene, paint
thinner, or scouring powder, as they may damage
the unit surface.
• Keep the unit dry.
• Clean the wall behind the air outlet periodically,
as it may become dirty.
Filter Cassette Replacement
The CHANGE FILTER indicator will signal when to
replace the filter cassette. The replacement period
will vary depending on the hours of use, air quality,
and location of the unit. However, most filters in
normal use need to be replaced annually.
For your convenience, all three filters (Washable
Anti-Bacterial Pre-Filter, HEPA Filter, and Washable
Nano-Silver Mesh/Carbon Filter) come in one pre-
packaged replacement cassette.
For optimum unit efficiency, wash the Washable
Anti-Bacterial Pre-Filter and Washable Nano-Silver
Mesh/Carbon Filter as described in Filter Cleaning
every three months.
Do not wash and reuse the HEPA Filter—it will not
work effectively.
Changing Filter
Warning: Before replacing or cleaning any
filters, make sure to remove the power plug
from the wall outlet.
• Remove the front panel by grasping the
bottom outside edges and gently pulling
toward you.
• Pull out the filter cassette by grasping
the tabs located on each side.
• Remove the plastic wrap from the new
filter cassette.
• Place the new filter cassette in the main
unit.
• Replace the front panel after pressing
CHANGE FILTER reset button.
• Plug in the power cord to a wall outlet and
turn on the unit.
Maintenance and Care Maintenance and Care
RI-FB_Manual_4.06.indd 14-15 5/1/06 7:19:38 PM

16
17
Maintenance and Care Maintenance and Care
Filter cleaning
Note: Never attempt to remove the HEPA Filter
from the cassette frame. Never attempt to clean
the HEPA Filter. Replace the entire cassette when
CHANGE FILTER indicator activates.
Cleaning the Washable Anti-Bacterial Pre-Filter
and the Washable Nano-Silver Mesh/Carbon
Filter is recommended every three months with
normal use. The interval between cleanings will
vary based on room conditions.
Cleaning filter continued…
• Remove the front panel and filter cassette as
described in Changing Filter (page 15).
• Remove the Pre-Filter by gently pulling one
side of the cassette frame outward while lifting
the Pre-Filter tab at the same time. When one
edge is clear of the frame, the Pre-Filter will
slide out for cleaning.
• Lightly vacuum the Pre-Filter and wash with
water and a mild household detergent. Rinse,
and shake off excess water.
• To remove the Washable Nano-Silver Mesh/
Carbon Filter, turn the cassette over and place
face-down on an even surface. Slightly flex the
cassette frame outward while pulling up on
the long tab. When the first corner is released,
pull out on the other long frame tab while
continuing to pull out on the filter tab. When
one long edge of the filter is free, slide out
for cleaning.
• Wash the filter in warm water with a mild
household detergent. Rinse, and shake off
excess water.
• Do not dry the two filters—running the unit will
be sufficient to dry them.
CASSETTE
LONG TABS
FILTER CASSETTE
FILTER TAB
CASSETTE
SHORT TABS
RI-FB_Manual_4.06.indd 16-17 5/1/06 7:20:04 PM