RICHTECH V2 LITE User manual

COPYRIGHT RICHTECH 2020
- 1 -
Automated AI Temperature Sensing System (AATSS)
Model V2 USER MANUAL
Please Note:
This Manual is to ensure that the user can use the product correctly, to avoid danger or
property loss in operation. So please read it carefully before using this product and keep
it for future reference. Without written permission, no entity or individual is allowed to
extract, copy, translate or modify all or part of this manual in any way. Unless otherwise
agreed, the company does not provide any express or implied statement or guarantee
for this manual
Attention
①Do not splash liquid or metal on the outer screen to avoid scratches or damages
②Use specialized detergent to clean the equipment to avoid watermarks
③Please ensure that the equipment is well grounded to avoid interference and
damage to video and audio signals

COPYRIGHT RICHTECH 2020
- 2 -
1. About AATSS model V2
The V2 is designed for easy integration into your local area network and existing access
control systems. Combining high-precision infrared temperature detection with face
recognition technology and a full suite of software functions, the AATSS V2 is the
finalized all-in-one solution for fully-automated quick contactless temperature screening.
2. Quick installation
2.1. Stand installation
The AATSS V2 comes with a Table Stand, if you ordered a Display Pedestal, the
installation method is very similar.
2.1.1. Open stand base backside, use the screw driver to remove the backside cover.

COPYRIGHT RICHTECH 2020
- 3 -
2.1.2. Slip the V2 interface cables through the center hole of the Stand Base
2.1.3. Affix the V2 to the Stand Base and secure from the bottom using the helix nut
provided

COPYRIGHT RICHTECH 2020
- 4 -
2.1.4. Connect the USB, Ethernet, and Power Cable to the Stand Base connectors
2.1.5. Pass all the data interface cables through the hole in the stand backside cover.

COPYRIGHT RICHTECH 2020
- 5 -
2.1.6. Secure the backside cover using screws
2.1.7. Complete installation, adjust the screen to the side with the blue light bar.

COPYRIGHT RICHTECH 2020
- 6 -
2.2. Power adapter connection and ethernet connection
Connect the power supply to the base of the stand. The system will start automatically
after powering on, the boot time is about 30 - 40 seconds.
If you need to manage the V2 through a network, connect the base to your router
through an ethernet cable. For how to set up the network, please refer to the following
Software section.
If you would like to connect the device to an existing access control system, please refer
to the Access Control Integration section.

COPYRIGHT RICHTECH 2020
- 7 -
3. Software
Note: We recommend using Windows 10 when managing the AATSS V2.
3.1. Network Preparation
After connect the V2 and the router using an ethernet cable, you must make sure the V2
is within the same intranet as your computer. See Section 3.2.

COPYRIGHT RICHTECH 2020
- 8 -
3.2. Network Configuration (Please read carefully)
The default IP address of the V2 is 192.168.1.8.
You will need to change your computer’s static IP address to be on the same network
segment as V2. You can change your IP address to 192.168.1.XXX (XXX here could be
from 2~254, but not 8 to avoid conflict with V2. So for example, 192.168.1.200 will
work).
Subnet mask: 255.255.255.0
Default gateway: Ask your network administrator for gateway IP. If you don’t know the
gateway IP address, leave it blank.
If you have trouble, you can refer to a video demonstration for setting up the network on
our website, www.richtech-ai.com
After that is complete, open Internet Explorer 10 or higher and put 192.168.1.8 in the
URL and hit enter. This will connect to the V2 management portal.

COPYRIGHT RICHTECH 2020
- 9 -
3.3. Plugin Installation
You will be guided to install a plug-in. Click the download link to download it and install
the plug-in. Allow all access when prompted.
After installing the plug-in, visit 192.168.1.8 again to open the login page.
Initial username is admin, and the password is blank.
After logging in, change your login information at:
Remote Settings -> System Configuration -> User Management.

COPYRIGHT RICHTECH 2020
- 10 -
3.4. Network Configuration
The default IP address of the V2 is 192.168.1.8. If you want to change the IP address to
a different one, you can so in Remote Settings -> Network Configuration.
Please ask your network administrator about which IP address is allowed on your
network. Please remember to keep V2’s IP address in the same segment as your
computer terminal.
You can always find the V2’s IP address on left corner of its screen.
3.5. Face Recognition Library Setup
To input all your employees into the system, you will need to collect each employee’s
photo (each file should be less than 256k). You can add photos one by one or in a
batch. Please enter all employee photos and names into the Whitelist group. If you want
to block some from accessing your facility, please input the photo into the Blacklist
group.