RICHTECH V3 User manual

v

v
1
PLEASE NOTE:
The purpose of this manual is to ensure that the user can use this product
correctly, and to avoid danger or damage to the product during operation.
Please read this manual carefully before using the product and keep it for
future reference. Without written permission, no entity or individual is
allowed to extract, copy, translate or modify all or part of this manual in any
way. Unless otherwise agreed upon, the company does not provide any
express or implied statement or guarantee.
ATTENTION:
1Do not splash liquid on the outer screen or make contact with metalto
avoid scratches and/or damage
2Use specialized detergent to clean the equipment to avoid
watermarks
3Please ensure that the equipment is well grounded to avoid
interference and damage to video and audio signals
4Please wait 5-10 minutes after the unit is initially switched on for it to
detect temperature accurately

v
2
1.About AATSS model V3
The V3 is designed for easy integration into your local area network and
existing access control systems. Combining high-precision infrared
temperature detection with face recognition technology and a full suite of
software functions, the AATSS V3 is the ultimate all-in-one solution for
swift fully-automated contactless temperature screening.
2.Table Stand installation
2.1. Slip the V3 interface cables through the center hole of the Stand Base.

v
3
2.2. Screw the V3 mount into the base stand and secure it from the bottom
using the helix nut provided. The mount is meant to be screwed in, not
forced in directly.
2.3. Connect the Ethernet and Power Cable to the Stand Base connectors.

v
4
2.4. Completed installation:
3.Display Pedestal Installation
If you ordered a Display Pedestal, the installation method is very similar to
the Table Stand.

v
5
3.1 Open the stand base and use the screwdriver to remove the backside
cover.
3.2 Slip the V3 interface cables through the center hole of the Stand Base.

v
6
3.3 Pass all the data interface cables through the hole in the stand
backside cover.
3.4 Connect the USB, Ethernet, and Power Cable to the Stand Base
connectors.

v
7
3.5 Screw the V3 mount into the base stand and secure it from the bottom
using the helix nut provided. The mount is meant to be screwed in, not
forced in directly.
3.6 Secure the backside cover using screws.

v
8
3.7 Upon completing installation, adjust the screen to the side with the blue
light bar.
3.8 Power Adaptor Connection and Ethernet Connection
Connect the power supply to the base of the stand. The system will start
automatically after powering on, the boot time is about 30 - 40 seconds.
If you need to manage the V3 through a network, connect the base to your
router via an ethernet cable. For instructions on how to set up the network,
please refer to the following Software section.
If you would like to connect the device to an existing access control system,
please refer to the Access Control Integration section.

v
9
4. About V3 QR Kiosk model
The V3 QR Kiosk is designed for easy integration into your local area
network and existing access control systems. Combining high-precision
infrared temperature detection with face recognition technology and a full
suite of software functions, the V3 QR Kiosk is the ultimate all-in-one
solution for swift fully-automated contactless temperature screening.
In the Health Questionnaire Mode, you can use your smartphone/ tablet
finish the questionnaire and get a complete QR code. The code can be
read on the V3 QR Kiosk code reading area. The temperature
measurement only activates after you pass the questionnaire and QR code
reading successfully. A badge prints out after the temperature scan.

v
10
4.1 Install the stand base and the column
4.1.1 Open the back cover of the column
4.1.2 Screw the column with the stand base

v
11
4.1.3 Tighten the stand base
4.1.4 Secure the back cover on the column

v
12
4.1.5 Installation complete

v
13
4.2 Paper Installation
ATTENTION: When device shows “OUT OF PAPER.PLEASE
CHECK AND ADD PAPER”, you need to check and add paper.
4.2.1 Press the printer button
4.2.2 Put the label paper inside of the printer

v
14
4.2.3 Close the printer cover
4.2.4 Connect the power and Ethernet cable to the stand base connectors

v
15
4.3 QR Code Reading and Temperature Scanning
4.3.1 Put the complete QR code in front of the QR code reading area
4.3.2 After validating the QR code, you can stand in front of the device to
start temperature checking

v
16
4.3.3 The printer prints a badge after the scanning
4.4. Software
To keep your device updated, please visit
www.richtech-ai.com/resources
to get the latest software, user manual, and setup tutorial video.

v
17
www.richtech-ai.com
[e-mail]
[phone]