Ricoh FT2050 Quick start guide

RICOH
RICOH FT2050/2070
FIELD SERVICE MANUAL
RICOH COMPANY LTD.

CONTENTS
SECTION 1 : INSTALLATION REQUIREMENTS
SECTION 2: UNPACKING AND INSTALLATION
SECTION 3: PREPARATIONS FOR TRANSPORTING THE COPIER
SECTION 4: SERVICE TABLES AND REMARKS
SECTION 5: REPLACEMENT AND ADJUSTMENT
SECTION 6: SORTER CS1040
SECTION 7: DOCUMENT FEEDER DF36
SECTION 8: TROUBLE SHOOTING
SECTION 9: ELECTRICAL DATA

CAUTIONS
1. Before installing the machine, make sure that there is a suitable ground (earth) available.
2. Since some parts of the copier are supplied with high voltage, make sure the main switch is off and the
power supply cord is unpluged before working on the copier.
3. When working on the fusing section, make sure that the fusing unit is cold.
4. When standing the clamshell straight up, place a block that has a height of approximately 80 mm (approx.
3") in front of the exit cover.
5. Do not turn on the safety switch when the clamshell is open.

SECTION 1
INSTALLATION
REQUIREMENTS

1-1.
1.
2.
3.
4.
5.
6.
Environment
Temperature Range :
Humidity Range :
Ambient Illumination :
Ventilation :
Ambient Dust :
Room Size
.
.
10°C to 30°C
7.
(50°F to 86°F)
15% to 90% RR
Less than 1,500 Iuxs (Do
not expose to direct
sunlight)
Room air should turn over
at least 3 times/hour.
Less than 0.1 5mg/m3
8.
More than 10m³ (13.4 yd³)
9.
10.
11.
If the installation place is air-conditioned or heated,
place the machine:
a.
b.
c.
Where it will not be subjected to sudden
temperature changes from low to high, or vice
versa.
Where it will not be directly exposed to cool air
from an air conditioner in the summer.
Where it will not be directly exposed to reflected
heat from a space heater in winter.
Avoid placing the copier in an area filled with
corrosive gas.
Avoid any area higher than 2,000m (6,500 feet)
above sea level.
Place the copier on a strong and level base.
Avoid any area where the copier may be subjected
to frequent strong vibration.
1-1

February 1. 1986
1-2. Minimum Space Requirements More than 12 cm (4-3/4")
1. Front :70 cm (27-1/2")
2. Back :12 cm (4-3/4")
3. Right :70 cm (27-1/2")
4. Left :70 cm (27-1 /2")
1-3. Power Source
1. Input voltage level 3. Permissible extension cord:
110V/60Hz : More than 12A At least 300V, 30A capacity and less than 5m
115V/60Hz : More than 12A (16.4") long.
220V/50Hz : More than 6A
240V/50Hz : More than 6A Note: 1. Be sure to ground the machine.
(Do not connect the grounding wire to
2. Permissible voltage fluctuation: ±10%
a gas pipe.
2. Make sure the plug is firmly inserted in
the outlet.
3. Avoid multi-wiring.
4. Do not set anything on the power cord.
1-2

SECTION 2
UNPACKING
AND
INSTALLATION

August 1, 1985
2-1. Unpacking Procedure
1. Take out the accessory box and the machine.
2. Remove the two cushion blocks.
3. Open the vinyl bag and take out the machine.
2-1

August 1, 1985
Check that the accessories are in the quantities
according to the following list.
Cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 pcs.
(One is in the machine.)
Cassette Cover . . . . . . . . . . . . . . . . . . . . . . . ..1 pc
Copy Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 pc
Manual Feed Guide . . . . . . . . . . . . . . . . . . . . . . 1 pc
Master Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 pc
NOTE: Keep it in the box until installing it in the
copier.
Toner . . . . . . . . . . . . . . . . . . . . . .
1 cartridge (Black)
●
Operating instructions . . . . . . . . . . . . . . . . . . . 1 pc
N.E.C.R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 pc
Envelope for N.E.C.R. (115Vonly) . . . . . . . . . 1 pc
Multi-lingualDecal(220/240Vonly) . . . . . . . 1 pc
Paper Size Decal . . . . . . . . . . . . . . . . . . . . . . . . 1 pc

2-2. Installation Procedure
1. Remove the two strips of tape.
2. Open the front cover.
3. Move the slider to the center and push down the
release lever to open the top unit.
2