Ricoh FV-L500B1 Installation instructions

1/12
FV-L500B1
Product Specifications Rev. 1.02
Small ubic Type
5.0 Mega Pixel D
Monochrome Po L amera Link amera
FV-L500B1
Product Specifications
RICOH COMPANY, LTD.

2/12
FV-L500B1
Product Specifications Rev. 1.02
opyright & Disclaimer
Sensor Technology o., Ltd. (DBA Sentech) believes the contents and specifications of its website, catalog,
documentation and ads are correct; however, Sentech provides no representation or warranty regarding such
information or product(s) contained therein. It is requested that Sentech be given appropriate acknowledgement in any
subsequent use of such work by a third party.
While every effort has been made to ensure that the details contained in Sentech’s website and all documentation are
correct and up-to-date, Sentech assumes no liability, legal or otherwise for any errors in listings, specifications, part
numbers, process, software or model applications. Sentech reserves the right to change specifications, product
descriptions, product quality, pricing and application at any time without prior written or oral notice. Any party using
such information assumes all risk for any and all damaged caused to themselves, a third party and/or property by
virtue of incorrect information and/or failure of these products. By installing and/or using a Sentech software
development kit or other similar product and/or information obtained from Sentech’s website, catalog, documentation
or ads, you hereby accept and understand these stated terms and conditions.

3/12
FV-L500B1
Product Specifications Rev. 1.02
Table of Contents
1. Safety / Prod ct Preca tions............................................................................................................................... 4
2. Electronic / Mechanical / Environmental Specifications................................................................................... 6
2.1. Spectral Sensitivity haracteristics.....................................................................................................................7
3. Connector Specifications.....................................................................................................................................8
3.1. amera Link onnector......................................................................................................................................8
3.2. Power-I/O onnector ..........................................................................................................................................9
3.3. Equivalent ircuit for the Input Pin of the I/O onnector.................................................................................. 10
4. Dimensions.......................................................................................................................................................... 11
5. Revision History..................................................................................................................................................12

4/12
FV-L500B1
Product Specifications Rev. 1.02
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUC E TH E R ISK OF EL ECTRIC SHOC K, DO N OT
REMOVE C OVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The l ghtn ng flash w th arrowhea d
symbol, w th n an equ lateral tr angle,
s nt ended t o alert the user t o the
presence of un nsulated “dangerous
v o l ta g e ” w th n th e p r o du c t ’s
enclosure that may be of suff c ent
ma gn tude t o c onst tute a r sk of
electr c shock to persons.
The exclama t on po nt w th n an
equ lateral tr angle s ntended to alert
the user to the presence of mport ant
operat ng and ma ntenance (serv c ng)
n st r u c t o ns n t h e l te r a t u r e
accompany ng the appl ance.
Warn ng:
Th s equ pment generates and uses rad o frequency energy and f
not nstalled and used properly, I.e., n str ct accordance w th the
nstruct on manual, may cause harmful nterference to rad o
commun cat ons. It has been tested and found to comply w th the
l m ts for a Class A comput ng dev ce pursuant to Subpart J of Part
15 of FCC Rules, wh ch are des gned to prov de reasonable
protect on aga nst such nterference when operated n a commerc al
env ronment.
For U.S.A.
Warn ng:
Th s d g tal apparatus does not exceed the Class A l m ts for rad o
no se em ss ons from d g tal apparatus set out n the Rad o
Interference Regulat ons of the Canad an Department of
Commun cat ons.
For Canada
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
1. Safety / Prod ct Preca tions
Safety Preca tions
Prod ct Preca tions
 Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper
handling or storage could damage the camera.
 Do not pull or damage the camera cable.
 During camera use, do not wrap the unit in any material. This will cause the internal temperature of
the unit to increase.
 Do not expose the camera to moisture, or do not try to operate it in wet areas.
 Do not operate the camera beyond its temperature, humidity and power source ratings.
 While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or
contamination from getting in the D or filter area and scratching or damaging this area.
 Do not keep the camera under the following conditions:
In wet, moist, and high humidity areas
• Under hot direct sunlight
• In high temperature areas
• Near an object that releases a strong magnetic or electric field
• Areas with strong vibrations
 Apply the power that satisfies the requirements specified in this document to the camera.
 Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO
not scratch the surface of the glass.

5/12
FV-L500B1
Product Specifications Rev. 1.02
 The camera is a general-purpose electronic device; using the camera for the equipment that may
threaten human life or cause dangers to human bodies directly in case of failure or malfunction of
the camera is not guaranteed. Use the camera for special purposes at your own risk.

6/12
FV-L500B1
Product Specifications Rev. 1.02
2. Electronic / Mechanical / Environmental Specifications
Model N mber FV-L500B1
Imager 2/3” Interline 5.0 Mega Pixel monochrome progressive: I X625AL
Total Picture Elements 2456 (H) x 2058 (V)
Active Picture Elements 2448 (H) x 2058 (V)
ell Size 3.45 (H) x 3.45 (V) µm
Scanning System Progressive
Scanning Method
Full Scanning, Partial Full Scanning,
½ Partial Scanning, ¼ Partial Scanning, Variable Partial Scanning,
Binning, Binning Partial Scanning,
Binning ½ Partial Scanning, Binning ¼ Partial Scanning,
Binning Variable Partial Scanning
Vertical Frequency
(Frame Rate) 16 Hz
Horizontal Frequency 33.264 kHz
Pixel Frequency 64 MHz
@ 8bit output <= 4 Digit (Gain 0 dB)
@ 10bit output
<= 15 Digit (Gain 0 dB)
S/N Ratio
(Standard
Deviation) @ 12bit output
<= 60 Digit (Gain 0 dB)
Minimum Scene Illumination
0.24 Lux at F1.2
Sync. System Internal
Video Output Format Digital 8, 10, or 12 bit amera Link (Base onfiguration)
Tap onfiguration 2 Taps (2XE-1Y)
Exposure Time OFF, 1/8 to 1/209,000 sec. (Variable at every H and clock)
Gain 0 to 18.309 dB
Gamma 1.0
Input Voltage D 12V± 10% via amera Link connector
Power onsumption Less than 4.0 W
Operational Mode Free-run, Edge Preset Trigger (V-reset, Non-reset);
Pulse Width Trigger (V-reset, Non-reset)
Electronic
Specifications
ommunication RS232 via amera Link connector
Dimensions 35 (W) x 35 (H) x 30.2 (D) mm (NOT including lens mount and the connector)
35 (W) x 35 (H) x 40.7 (D) mm (NOT including the connector)
Optical Filter No IR cut filter
Materials Aluminum (A )
Lens Mount mount
Interface onnector I/O onnector: HR 10A-7R-6PB (Hirose) or equivalent
amera Link onnector: SDR (3M) or equivalent
Mechanical
Specifications
Weight Approximately 80g
Operational
Temperature: -5 to 40⁰
Environmental
Specifications
Temperature
Storage
Temperature: -30 to 65⁰

7/12
FV-L500B1
Product Specifications Rev. 1.02
Vibration 20Hz to 200Hz to 20Hz (5min./cycle);
Acceleration 10G, 3 directions 30 min. each
Shock Acceleration 38G, half amplitude 6ms, 3 directions 3 times each
Standard ompliancy EMS: EN61000-6-2, EMI: EN55022 ( lass B) , F PART15 subpart B classA
RoHS RoHS ompliant
2.1. Spectral Sensitivity haracteristics
1
0.8
0.4
0.6
0.2
0
400 500 600 700 800 900 1000
Relative Response
Wave length [nm]

8/12
FV-L500B1
Product Specifications Rev. 1.02
3. Connector Specifications
3.1. amera Link onnector
SDR (3M) or equivalent
This prod ct is a PoCL type.
When a frame grabber is PoCL compliant, DO NOT SUPPLY POWER FROM THE I/O CONNECTOR.
When a frame grabber is NOT PoCL compliant, s pply power from the I/O connector.
Pin Assignment
Pin No. Signal Name Pin No. Signal Name
1 +12V 14 GND
2 X0- 15 X0+
3 X1- 16 X1+
4 X2- 17 X2+
5 Xclk- 18 Xclk+
6 X3- 19 X3+
7 SerT + 20 SerT -
8 SerTFG- 21 SerTFG+
9 1-(TRG) 22 1+(TRG)
10 2+ 23 2-
11 3- 24 3+
12 4+ 25 4-
13 GND 26 +12V
Power-I/O onnector
amera Link onnector

9/12
FV-L500B1
Product Specifications Rev. 1.02
3.2. Power-I/O onnector
 HR10A-7R-6PB（Hirose）or equivalent
 This connector is for the power supply (12Vdc) and input /output signals.
 Use HR10A-7P-6S (Hirose) or equivalent for the cable side.
Pin Assignment
 Input/output signals can be assigned through the camera setting communication (see table 4).
 Trigger input signal can be assigned either on amera Link connector ( 1) or on the No. 2 pin of the
Power-I/O connector through the camera setting communication.
IO Signal Patterns
Note 1: Output trigger signal has a latency of 30 LK (Approximately 470 nseconds) from input trigger signal.
Note 2: To input trigger signal from the I/O connector, change the setting of 12H.5.
Note 3: EXPDUR becomes high during exposure.
Voltage
Pin No. Signal Name IN / OUT Low Voltage High Voltage
1 GND IN 0V
IN 0 to +0.99V +2.3 to +3.3V
2 I/O-1 IN/OUT OUT 0V +3.3V
3 I/O-2 OUT OUT 0V +3.3V
4 I/O-3 OUT OUT 0V +3.3V
5 I/O-4 OUT OUT 0V +3.3V
6 +12Vdc IN +12Vdc
Command No. HR10A-7R-6PB (Hirose)
No.2 Pin No.3 Pin No.4 Pin No.5 Pin
F0H[3..0] I/O-1 (SP4) I/O-2 (SP3) I/O-3 (SP2) I/O-4 (SP1)
Option 0
(Initial Setting) 0H IN/TRG N/A N/A OUT/TRG
Option 1 1H For Test Use Only
Option 2 2H OUT/ 4 OUT/ 3 OUT/ ”2 OUT/ 1
Option 3 3H OUT/FVAL OUT/XSG OUT/XSUB OUT/ 1
Option 4 4H
OUT/FVAL OUT/LVAL
OUT/
Right Image Data
(MSB)
OUT/
Left Image Data
(MSB)
Option 5 5H OUT/XHD
(high-active)
OUT/EXPDUR
(Exposure) OUT/TRG OUT/ 1
Option 6 6H OUT/VD N/A N/A OUT/HD
Others 7H-FH For Test Use Only

10/12
FV-L500B1
Product Specifications Rev. 1.02
3.3. Equivalent ircuit for the Input Pin of the I/O onnector
+3.3V +3.3V
T 7WH241FK
TOSHIBA
TRIGGER IN
10kohm
100ohm
On resister Max. = 30ohm

11/12
FV-L500B1
Product Specifications Rev. 1.02
4. Dimensions
Unit: mm

12/12
FV-L500B1
Product Specifications Rev. 1.02
5. Revision History
Rev Date hanges Note
1.00 2012/06/15 Initial Release
1.01 2012/07/13 Updated
Document Title
Dimensions
Electronic Specifications
Shutter Speed  Exposure Time
1.02 2012/09/27 Updated
Power supply through No.6 pin of the power-I/O connector became available.
RICOH COMPANY, LTD.
URL http://www.ricoh.com/fa_security/