manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Ricoh
  6. •
  7. Security Camera
  8. •
  9. Ricoh FV-G200B1 Installation instructions

Ricoh FV-G200B1 Installation instructions

1/14
FV-G200B1
Product Specifications Rev. 1.03
Gig Vision
UXGA Monochrome CCD Camera
FV-G200B1
Product Specifications
RICOH COMPANY, LTD.
2/14
FV-G200B1
Product Specifications Rev. 1.03
Copyright & Disclaimer
Sensor Technology Co., Ltd. (DBA Sentech) believes the contents and specifications of its website, catalog, documentation
and ads are correct; however, Sentech provides no representation or warranty regarding such information or product(s)
contained therein. It is requested that Sentech be given appropriate acknowledgement in any subsequent use of such work
by a third party.
While every effort has been made to ensure that the details contained in Sentech’s website and all documentation are
correct and up-to-date, Sentech assumes no liability, legal or otherwise for any errors in listings, specifications, part
numbers, process, software or model applications. Sentech reserves the right to change specifications, product
descriptions, product quality, pricing and application at any time without prior written or oral notice. Any party using such
information assumes all risk for any and all damaged caused to themselves, a third party and/or property by virtue of
incorrect information and/or failure of these products. By installing and/or using a Sentech software development kit or
other similar product and/or information obtained from Sentech’s website, catalog, documentation or ads, you hereby
accept and understand these stated terms and conditions.
3/14
FV-G200B1
Product Specifications Rev. 1.03
Table of Contents
1 Safety / Prod ct Preca tions ...............................................................................................................................4
2 Electronic / Mechanical / Environmental Specifications...................................................................................6
2.1
Spectral Sensitivity Characteristics......................................................................................................................... 8
3 Connector Specifications.....................................................................................................................................9
3.1
RJ45 Connector ...................................................................................................................................................... 9
3.2
DC Iris Lens Connector ........................................................................................................................................ 10
3.3
Power-I/O connector............................................................................................................................................. 10
3.3.1
quivalent Circuit for the Input Pin of the I/O Connector .................................................................................. 12
4 Dimensions ..........................................................................................................................................................13
4/14
FV-G200B1
Product Specifications Rev. 1.03
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE TH E RISK OF EL ECTRIC SHOCK, DO N OT
REMOVE COVER (OR BAC K). NO USER SERVICEAB LE
PARTS INSIDE.
REFER SERVIC ING TO QUALIFIED SERVICE PERSONNEL.
The l ghtn ng flash w th arrowhead
symbol, w th n an equ lateral tr angle,
s nt ended to alert the use r t o the
pre sence of un nsulated “dangerous
v o l t a g e ” w th n th e p r o du ct ’ s
enclosure t hat may be of suff c ent
ma gn tude to c onst tute a r sk of
electr c shock to persons.
The exclamat on po nt w t h n an
equ lateral tr angle s ntended to alert
the user to the presence of mportant
operat ng and ma ntenance (serv c ng)
n st r u c t o ns n t h e l te r a t u r e
accompany ng the appl ance.
Warn ng:
Th s equ pment generates and uses rad o frequency energy and f
not nstalled and used properly, I.e., n str ct accordance w th the
nstruct on manual, may cause harmful nterference to rad o
commun cat ons . It has been tested and found to comply w th the
l m ts for a Class A comput ng dev ce pursuant to Subpart J of Part
15 of FCC Rules, wh ch are des gned to prov de reasonable
protect on aga nst such nterference when operated n a commerc al
env ronment.
For U.S.A.
Warn ng:
Th s d g tal apparatus does not exceed the Class A l m ts for rad o
no se em ss ons from d g tal apparatus set out n the Rad o
Interference Regulat ons of the Canad an Department of
Commun cat ons.
For Canada
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
1 Safety / Prod ct Preca tions
Safety Preca tions
Prod ct Preca tions
 Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper handling or
storage could damage the camera.
 Do not pull or damage the camera cable.
 During camera use, do not wrap the unit in any material. This will cause the internal temperature of the
unit to increase.
 Do not expose the camera to moisture, or do not try to operate it in wet areas.
 Do not operate the camera beyond its temperature, humidity and power source ratings.
 While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or
contamination from getting in the CCD or filter area and scratching or damaging this area.
 Do not keep the camera under the following conditions:
In wet, moist, and high humidity areas
• Under hot direct sunlight
• In high temperature areas
• Near an object that releases a strong magnetic or electric field
• Areas with strong vibrations
 Apply the power that satisfies the requirements specified in this document to the camera.
 Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO not
scratch the surface of the glass.
5/14
FV-G200B1
Product Specifications Rev. 1.03
 The camera is a general-purpose electronic device; using the camera for the equipment that may
threaten human life or cause dangers to human bodies directly in case of failure or malfunction of the
camera is not guaranteed. Use the camera for special purposes at your own risk.
6/14
FV-G200B1
Product Specifications Rev. 1.03
2 Electronic / Mechanical / Environmental Specifications
Prod ct FV-G200B1
Imager 1/1.8” Interline UXGA monochrome progressive CCD: ICX274AL
Total Picture lements 1688 (H) x 1246 (V)
Active Picture lements UXGA: 1624 (H) x 1236 (V)
Cell Size 4.4 (H) x 4.4 (V) µm
Scanning System Progressive
Vertical Frequency
(Frame Rate)
15.31668 Hz at full resolution
0.29261 to 61.26674 Hz adjustable via the communication
(Frame rate depends on the AOI setting)
Maximum frame rate (61.26674 Hz) is when vertical resolution AOI setting is 232.
Horizontal Frequency 19.1761 kHz
Pixel Frequency 36.8181 MHz
@ 8bit output ≤ 3 Digit (Gain 0 dB)
@ 10bit output ≤ 12 Digit (Gain 0 dB)
Noise
Level @ 12bit output ≤ 48 Digit (Gain 0 dB)
Minimum Scene Illumination 0.16 Lux at F1.2, 15.31668 Hz
Sync. System Internal
Video Output Format Digital 8, 10 or 12 bit Raw Data or RGB 8 bit
Interface I 802.3 (1000BAS -T)
Protocol Gig Vision® 1.2 and GenICam™ 2.0 compliant
xposure Time
Preset continuous mode: 1 useconds to 16,777,215 useconds
Preset trigger mode: 1 useconds to 16,777,215 useconds
Pulse width mode: 1 useconds to Unlimited
ALC Auto iris lens, electronic iris and AGC (ON/OFF)
Gain 0 to 20.4 dB
Gamma Gamma 1.0 (Factory default) or uploadable gamma table
AOI Function Programmable AOI setting via the communication
Smear Reduction Selectable ON/OFF via the communication
Operational Mode Free-run, dge preset trigger, Pulse width trigger (unlimited long exposure)
Communication UART Communication through thernet port
I/O One opt-isolated input and two open-collector outputs
Auto IRIS Lens Control DC IRIS control input with video level target, peak/average and zone weight settings
via the communication
Input Voltage +10.8 to +26.4 Vdc
lectronic
Specifications
Power Consumption
Less than 5.00 W
Dimensions 35 (W) x 35 (H) x 50.8(D) mm excluding connectors
Optical Filter No Filter
Optical Center Accuracy Positional accuracy in H and V directions: +/- 0.3 mm
Rotational accuracy of H and V: +/- 1.5 deg.
Material Aluminum (AC)
Lens Mount C mount
Connectors RJ45 connector
Power-I/O connector: HR10A-7R-6PB (Hirose) or equivalent
DC IRIS lens connector: M1951 ( MUD N) or equivalent
Mechanical
Specifications
Camera Mount Screws Two 1/4” Tripod screw holes: (One on each top and bottom plate),
Twelve M4 screws holes: (Four on each top and bottom plate, two on each side plate)
7/14
FV-G200B1
Product Specifications Rev. 1.03
Weight Approximately 120 g
Prod ct FV-G200B1
Minimum nvironmental Temperature -5⁰C
Operational
Temperature
Maximum
Camera housing temperature (top plate) shall not exceed 65⁰C
(This corresponds to an environmental temperature of approximately 35⁰C)
Storage temperature nvironmental Temperature: -30⁰C to 65⁰C
Vibration 20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each
Shock Acceleration 38G, half amplitude 6ms, 3 directions 3 times each
Standard Compliancy MS: N61000-6-2, MI: N55011, FCC PART15 subpart B classA
nvironmental
Specifications
RoHS RoHS Compliant
Note: Please use this camera in surrounding temperature conditions that are less than 35⁰C or in conditions where the
camera’s top case plate is less than 65⁰C.
When the camera is used in surrounding temperatures that exceed 35⁰C, please make sure that the camera is set up
to properly radiate heat (maintaining the camera’s top case plate’s temperature to be less than 65⁰C).
Taking these steps will maintain the heat rating of the electronic components of the camera.
8/14
FV-G200B1
Product Specifications Rev. 1.03
2.1 Spectral Sensitivity Characteristics
1
0.8
0.4
0.6
0.2
0
400 500 600 700 800 900 1000
Relative Response
Wave length [nm]
9/14
FV-G200B1
Product Specifications Rev. 1.03
3 Connector Specifications
3.1 RJ45 Connector
This prod ct is NOT a PoE type. Apply power (+10.8 to +26.4Vdc) ONLY thro gh the I/O connector.
Pin Assignment: L D Information:
Pin No. Signal Name
1 TA+
2 TA-
3 TB+
4 TC+
5 TC-
6 TB-
7 TD+
8 TD-
Please se a 1Gb s pported NIC, HUB and LAN cable. Check that the NIC and HUB being sed is “1Gb
transferring”.
Damaging or mishandling the CAT5e cable may ca se the transferring speed to change from 1Gb to 100Mb.
If this happens, please replace the CAT5e cable.
Green LED Yellow LED Stat s
Green Light ON Orange Light ON Power ON
Green Light ON Orange Light Blinking 1Gb Transferring
Light OFF Orange Light Blinking 100 Mb Transferring
Power-I/O Connector
DC Iris Lens Connector
RJ45 Connector
The camera is powered-on Green light: ON
Yellow light: Blinking
1 Gb Transferring
Green light: OFF
Yellow light: Blinking
100 Mb Transferring
10/14
FV-G200B1
Product Specifications Rev. 1.03
3.2 DC Iris Lens Connector
 M1951 ( MUD N) or equivalent.
Pin Assignment
Pin No.
Signal Name
1 DAMP-
2 DAMP+
3 DRIV +
4 DRIV -
3.3 Power-I/O connector
 HR10A-7R-6PB(Hirose)or equivalent
 This connector is for the power supply (12Vdc) and input /output signals.
 Use HR10A-7P-6S (Hirose) or equivalent for the cable side.
Pin Assignment
 Output signals can be assigned through the camera setting communication.
(Device Code = 00H, Command = F0H and F1H)
IO Signal Patterns for Pin No.2 (I/O-1) and Pin No.3 (I/O-2)
Pin No.
Signal Name
IN / OUT
Voltage
1 GND IN 0V
2 I/O-1 OUT +3.3V LVTTL
3 I/O-2 OUT +3.3V LVTTL
4 TRG_In- IN
5 TRG_In+ IN
Low: Smaller than +1.0V (Opt. Isolated -)
High: +3.0 to +26.4V (Opt. Isolated +)
*potential difference between TRG_In- and
TRG_In+
6 POW R IN IN +10.8 to +26.4 Vdc
Command No. HR10A-7R-6PB (Hirose)
F0H[3..0] F1[3] F0H[7..4] F1[4]
For I/O-1 (Pin No. 2) For I/O-2 (Pin No.3) I/O-1 (Pin No.2) / I/O-2 (Pin No.3)
0H
(initial setting) - 0H - FrameTriggerWait
(initial setting for I/O-1)
1H Set Value 1H Set Value UserOutput
2H - 2H
(initial setting) xposureActive
(initial setting for I/O-2)
3H - 3H - TriggerAuxiliary
4H - 4H TriggerInternal
5H - 5H SensorReadOut
6H - 6H StrobeSignal
7H-FH - 7H-FH - For Test Use Only
1 2
3 4
11/14
FV-G200B1
Product Specifications Rev. 1.03
Note: I/O-1 can be assigned only by F0H[3..0] and F1[3], and I/O-2 can be assigned only by F0H[7..4] and F1[4].
1) FrameTriggerWait
The user can check the camera condition (camera exposure and image output processing by the trigger signal with
this FrameTriggerWait signal).
This signal is LOW for the period from the trigger input signal to the image output.
a) High status (3.3V): No processing by the trigger signal. The camera accepts the trigger signal.
b) Low status (0V): The camera is exposed and the image output processes by the trigger signal.
The camera default setting is the input trigger signal is INVALID while at the low status of this signal. When the
exposure starts while the image output by the next trigger signal, please change the camera setting (Device code:
00H, Command No. :13H) to accept the trigger signal while the image outputs.
The noise appears on the image when the exposure begins while the image is output. The noise appears on the
image when the start exposure while the image is output. In this case, please change the “H reset” for the exposure
start mode (Device code: 00H, Command No. : 12H) to change the exposure start point to the next HD timing.
2) UserOutput
The status of the UserOutput signal can change with the “UserOutputValue”.
a) High status (3.3V)
b) Low status (0V).
3) xposureActive
The user can check the exposure time with the xposureActive signal.
a) High status (3.3V): The camera is exposing
b) Low status (0V): The camera is not exposed
4) TriggerAuxiliary
The TriggerAuxiliary signal is the input trigger signal.
5) TriggerInternal
The TriggerInternal signal is the input trigger signal with the trigger delay time.
6) SensorReadOut
The SensorReadOut signal is the FVAL signal, which is the image output period of the time.
7) StrobeSignal
The StrobeSignal signal is the strobe control signal.
12/14
FV-G200B1
Product Specifications Rev. 1.03
3.3.1 quivalent Circuit for the Input Pin of the I/O Connector
+3.3V
+3.3V
+3.3V
TOSHIBA RN1105MFVTOSHIBA RN1105MFV
2
1 3
TOSHIBA TLP181TOSHIBA TLP181
34
6 1
2.2K2.2K
1
2
3
4
5
6
TOSHIBA RN1105MFVTOSHIBA RN1105MFV
2
1 3
1K1K
1K1K
+10.8 to +26.4V
Trigger_In+
Trigger_In-
IO_Out
IO_Out
GND
Customer GND
+3 to +26.4V
3 to 5mA
Trigger Signal
HR10A-7R-6PB (HIROS )
or equivalent connector
13/14
FV-G200B1
Product Specifications Rev. 1.03
4 Dimensions
Unit: mm
14/14
FV-G200B1
Product Specifications Rev. 1.03
Revision History
Rev
Date Changes Note
1.00
2012/06/17  Initial Release
1.01
2012/06/18  Updated
The output Signal “StrobeOut” is corrected to “StrobeSignal”
1.02
2012/07/03  Updated
Document title
lectronic Specifications
Shutter Speed  xposure Time
The maximum value for the xposure Time is corrected to 16,777,215
quivalent Circuit for the Input Pin of the I/O Connector
1.03
2012/08/25  Updated
Pin Assignment of Power-I/O Connector
RICOH COMPANY, LTD.
URL http://www.ricoh.com/fa_security/

Other manuals for FV-G200B1

1

Other Ricoh Security Camera manuals

Ricoh FV-G030B1 User manual

Ricoh

Ricoh FV-G030B1 User manual

Ricoh FV-L030B1 User manual

Ricoh

Ricoh FV-L030B1 User manual

Ricoh FV-G030B1 Installation instructions

Ricoh

Ricoh FV-G030B1 Installation instructions

Ricoh FV-G030B1 User manual

Ricoh

Ricoh FV-G030B1 User manual

Ricoh FV-L500B1 User manual

Ricoh

Ricoh FV-L500B1 User manual

Ricoh FV-L500B1 Installation instructions

Ricoh

Ricoh FV-L500B1 Installation instructions

Ricoh FV-G030B1 User manual

Ricoh

Ricoh FV-G030B1 User manual

Ricoh FV-G200B1 User manual

Ricoh

Ricoh FV-G200B1 User manual

Popular Security Camera manuals by other brands

D-Link DCS-4612EK Quick installation guide

D-Link

D-Link DCS-4612EK Quick installation guide

Dahua IPC-HFW2831T-AS quick start guide

Dahua

Dahua IPC-HFW2831T-AS quick start guide

4xem 4X-IP7160 Specifications

4xem

4xem 4X-IP7160 Specifications

Sony Ipela SNC-ER580 quick reference

Sony

Sony Ipela SNC-ER580 quick reference

COP-USA ASH56NVIR-TVI30 Operation manual

COP-USA

COP-USA ASH56NVIR-TVI30 Operation manual

Honeywell HD5 Series Quick install guide

Honeywell

Honeywell HD5 Series Quick install guide

ACTi I93 Hardware manual

ACTi

ACTi I93 Hardware manual

Bosch LTC0485/11 installation instructions

Bosch

Bosch LTC0485/11 installation instructions

Digital Watchdog D1362D Series instruction manual

Digital Watchdog

Digital Watchdog D1362D Series instruction manual

IOT-Smart Solutions MPTZ20XIRIP-TA Manual operation

IOT-Smart Solutions

IOT-Smart Solutions MPTZ20XIRIP-TA Manual operation

Samsung IPOLIS SNP-3300 user manual

Samsung

Samsung IPOLIS SNP-3300 user manual

Axis Q1910 installation guide

Axis

Axis Q1910 installation guide

TRENDnet TV-IP751WC user guide

TRENDnet

TRENDnet TV-IP751WC user guide

Dahua DH-IPC-HDBW4231FN-E2-M quick start guide

Dahua

Dahua DH-IPC-HDBW4231FN-E2-M quick start guide

JAI VIS-CAM System TS-1327EN installation manual

JAI

JAI VIS-CAM System TS-1327EN installation manual

FLIR DBB533TL quick start guide

FLIR

FLIR DBB533TL quick start guide

Milesight MS-C8272-FPB user manual

Milesight

Milesight MS-C8272-FPB user manual

Samsung SCC-B2315 Specifications

Samsung

Samsung SCC-B2315 Specifications

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.