RIGHT ANGLE 4 HV Series User manual

Read all the instructions before beginning.
K&A Manufacturing
Hardware Pack # 53368 Page1 OF 6Instruction # 53376
Series 4 HV Single Monitor
Lift Assembly Instructions
6703 Zinser Street
Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
6/13/17

15
This item is shown
1/4 of actual size.
52127
Hardware Is Drawn Actual Size
Page 2 OF 6
524065170850133
6703 Zinser Street Schofield, WI 54476
www.raproducts.com
Phone: [phone]
Tape Measure
K&A Manufacturing
51687
Square
Fax: [phone]
Tools Required for Assembly:
Power Driver W/Adjustable Torque
#2 Phillips Head Driver Bit
#2 Square Head Driver Bit
Phillips Screwdriver
3/16" Hex Head Driver Bit or
Allen Wrench
Level
Instruction # 53376
53360
112 13
14
16
15
Step 1 the workstation is fully
monitor mounting plate after
aside and slide it onto the
16
assembled and upright.
Monitor Mounting Plate
Step 1: Attach the quick
connect monitor bracket 15
to your monitor with (4)
machine screws 16 . Set it
9

Page 3 OF 6
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Instruction # 53376
IT M # PART # D SCRIPTION QTY.
1 51687 5mm Slim Fix Bolt 16
2 52253 19mm Rafix Connector Cam 16
3 Varies R-STYL HV-S RI S HOV R 1
4 Varies HV Series 4 Kick Panel 1
5 WZRHVSPL HV Series 4 Side Panel Left 1
6 WZRHVSPR HV Series 4 Side Panel Right 1
7 Varies HV Series 4 Worksurface 1
8 801298 HV Series 4 Column Assembly 1
9 WZRHVTP HV Series 4 Top Panel 1
10 Varies Left Leg Assembly 1
11 Varies Right Leg Assembly 1
12 50133 10-32 x 1/2 Phillips Truss Head Machine Screw 14
13 51708 M5 x 18mm (7/8") Sq/Ph/Wshr Head Wood Screw 5
14 52406 M6-1 x 30mm Phillips Pan Head Machine Screw 6
15 53360 Quick Connect Monitor Bracket 1
16 52127 M4-7 x 10 Phillips Pan Head Machine Screw 4
3
4
Step 2: Using a cordless drill and a #2 phillips head
driver bit, drive (16) slim fix bolts 1into the back
panel 3and the kick panel 4; (8) in each panel.
Step 3: Using a phillips screwdriver, make sure that
all of the cams on the left side panel 5and the right
side panel 6are in the open position (fully counter-
clockwise).
Step 2
2
in Side Panels
Clockwise
Loosen Counter-
Phillips Screwdriver
Cam Operation
Tighten Clockwise
Pre-installed
Step 3
(4) (4)
(4) (4)

www.raproducts.com
Instruction # 53376 Page 4 OF 6
Phone: [phone]
K&A Manufacturing
Fax: [phone]
6703 Zinser Street Schofield, WI 54476
Step 4: Lay the column assembly 8assembly on
the back panel 3as shown below.
Step 5: Attach the bottom plate of the column
assembly 8to the back panel 3by screwing (4)
machine screws 12 through the back of the
bottom plate and into the inserts installed in the
back panel. Do not fully tighten.
Step 6: Attach the side brackets to the back panel
3with (6) machine screws 12 as you did the
bottom plate. Do not fully tighten.
Step 7: Attach the top panel 9to the worksurface
support with (5) wood screws 13 . Do not fully
tighten.
Step 8: Square the top panel 9with the back
panel 3and fully tighten all the wood screws 13
holding the top panel to the worksurface support and
the machine screws 12 holding the column assembly
to the back panel. Set the assembly aside for
installation on the workstation later.
9
Steps 4-8
13
3
Bottom
Plate
came with them.
Mounting
Monitor
12
12
Bracket
8
Side
panel using the instructions that
Plate
nest, attach them to the back
Note: If your workstation has a
mouse nest and/or a keyboard
Worksurface Support

6703 Zinser Street Schofield, WI 54476
.
Page 5 OF 6
K&A Manufacturing
www.raproducts.com
Phone: [phone]
Instruction # 53376
Fax: [phone]
Step 9: Lay the left leg assembly 10 on a protected
surface with the threaded screw holes facing up.
Attach the left side panel 5to the leg assembly with
(3) machine screws 14 . The long side must face the
back. Do not fully tighten.
Step 10: Repeat Step 9with the right leg assembly 11
and the right side panel 6.
Step 11: Lay the worksurface 7on a protected
surface with the inserts facing up. Align the holes in the
left leg assembly 10 worksurface support with the
inserts in the worksurface. Attach the leg assembly to
the worksurface with (3) machine screws 12 . Do not
fully tighten.
Step 12: Repeat Step 11 with the right leg assembly
11
Steps 11 & 12
5
Steps 9 & 10
10
14
Back
12
7

Fax: [phone]
Page 6 OF 6
Phone: [phone]
K&A Manufacturing
www.raproducts.com
Instruction # 53376
6703 Zinser Street Schofield, WI 54476
Step 13: Insert the (8) slim fix bolts 1in the kick
panel 4into the connector cams 2pre-installed
in the left side panel 5and the right side panel 6.
You may need to move the side panels slightly to
align the bolts with the cams. Fully tighten the cam
locks. Important note: When tightening the cams,
they will stop at a detent in the mechanism before
they are fully tightened. Be sure to tighten them
past the detent.
14
4
10
at the top of the casters.
has casters, level it by turning the bolts
Step 14
corners of the unit. If your workstation
clockwise (from the top) on the low
Step 14: Insert the (8) slim fix bolts
1in the back panel into the connector
cams 2pre-installed in the left side
panel 5and the right side panel 6.
You may need to move the side panels
slightly to align the bolts with the cams.
Fully tighten the cam locks.
Step 15: Make sure all the panels are
square and level. Fully tighten the
machine screws 14 holding the side
panels to the leg assemblies 10 and
11 . Fully tighten the machine screws
12 holding the leg assemblies to the
worksurface 7.
Step 16: With the help of an assistant,
set the workstation upright in its final
location. Level the workstation if
required by turning the leveling glides
12
7
Glide
Toe Kick Not
Leveling
Shown For Clarity
3
Steps 15 & 16
Step 17: Raise the top panel 9to
its full height and slide the monitor
and the quick connect bracket 15
onto the monitor mounting plate
until it locks in place. See page 2.
Your workstation is now ready for
use.