Rigol DG2072 User manual

-1-

1
保证和声明
版权
©2019苏州普源精电科技有限公司
商标信息
RIGOL 是苏州普源精电科技有限公司的注册商标。
文档编号
QGB12000-1110
声明
本公司产品受中国及其它国家和地区的专利（包括已取得的和正在申请的专利）保护。
本公司保留改变规格及价格的权利。
本手册提供的信息取代以往出版的所有资料。
本手册提供的信息如有变更，恕不另行通知。
对于本手册可能包含的错误，或因手册所提供的信息及演绎的功能以及因使用本手册而导致的
任何偶然或继发的损失，RIGOL 概不负责。
未经 RIGOL 事先书面许可，不得影印、复制或改编本手册的任何部分。
产品认证
RIGOL 认证本产品符合中国国家产品标准和行业产品标准及ISO9001:2015 标准和
ISO14001:2015 标准，并进一步认证本产品符合其它国际标准组织成员的相关标准。
联系我们
如您在使用此产品或本手册的过程中有任何问题或需求，可与 RIGOL 联系：
电子邮箱：[e-mail]
网址：www.rigol.com
一般安全概要
1. 请使用所在国家认可的本产品专用电源线。
2. 请确保产品可靠接地。
3. 查看所有终端额定值。
4. 请使用合适的过压保护。
5. 请勿开盖操作。
6. 请勿将异物插入排风口。
7. 请使用合适的保险丝。
8. 避免电路外露。
9. 怀疑产品出故障时，请勿进行操作。
10.请保持适当的通风。
11.请勿在潮湿环境下操作。
12.请勿在易燃易爆的环境下操作。
13.请保持产品表面的清洁和干燥。
14.请注意防静电保护。
15.请注意搬运安全。
16.请正确使用前面板 BNC 输出连接器，仅允许
信号输出。
安全术语和符号
本手册中的安全术语：
警告
警告性声明指出可能会造成人身伤害或危及生命安全的情况或操作。
注意
注意性声明指出可能导致本产品损坏或数据丢失的情况或操作。

2
产品上的安全术语：
DANGER
表示您如果不进行此操作，可能会立即对您造成危害。
WARNING
表示您如果不进行此操作，可能会对您造成潜在的危害。
CAUTION
表示您如果不进行此操作，可能会对本产品或连接到本产品的其他设备造成
损坏。
产品上的安全符号：
高电压
安全警告
保护性接地端
壳体接地端
测量接地端
保养与清洁
保养
请勿将仪器放置在长时间受到日照的地方。
清洁
请根据使用情况定期对仪器进行清洁。方法如下：
1. 断开电源。
2. 用柔和的清洁剂或清水浸湿软布擦拭仪器外部，请注意不要将水或其他异物通过散热孔进入机
箱内。清洁带有液晶显示屏的仪器时，请注意不要划伤 LCD 显示屏。
注意
请勿使任何腐蚀性的液体沾到仪器上，以免损坏仪器。
警告
重新通电之前，请确认仪器已经干透，避免因水分造成电气短路甚至人身伤害。
文档概述
本文档介绍初次使用DG2000系列函数/任意波形发生器时需要了解的信息，包括产品简介、连接
电源、开机检查以及远程控制等。
提示
本手册的最新版本可登陆
RIGOL
网址（www.rigol.com）进行下载。
文档格式的约定
1. 按键：
本手册中通常用“文本框+文字（加粗）”表示前面板上的一个按键，如 Pulse/Utility。
2. 菜单标签：
本手册通常用“字符底纹+文字（加粗）”表示一个菜单标签，如系统设置。
3. 连接器：
本手册中通常用“方括号+文字（加粗）”表示前面板或后面板上的一个连接器。例如：
[Counter]。

3
4. 操作步骤：
本手册中通常用箭头“”表示下一步操作。例如： 在 Shift 键背灯变亮状态，按
Pulse/Utility系统设置表示按下前面板上的 Pulse/Utility 功能键后再触摸点击 系统设
置菜单标签。
文档内容的约定
DG2000系列函数/任意波形发生器包含以下型号。如无特殊说明，本手册以DG2102为例介绍其使
用方法。
型号
通道数
最大输出频率
DG2052
2
50MHz
DG2072
2
70MHz
DG2102
2
100MHz
一般性检查
1. 检查运输包装
如运输包装已损坏，请保留被损坏的包装或防震材料，直到货物经过完全检查且仪器通过电性
和机械测试。
因运输造成仪器损坏，由发货方和承运方联系赔偿事宜。RIGOL 公司恕不进行免费维修或更
换。
2. 检查整机
若存在机械损坏或缺失，或者仪器未通过电性和机械测试，请联系您的 RIGOL 经销商。
3. 检查随机附件
请根据装箱单检查随机附件，如有损坏或缺失，请联系您的 RIGOL 经销商。
产品简介
DG2000 系列函数/任意波形发生器是一款集函数发生器、任意波形发生器、噪声发生器、脉冲发
生器、谐波发生器、模拟/数字调制器、频率计等功能于一身的多功能信号发生器。多功能、高性
能、高性价比、便携式、触摸屏操作等特点为教育、研发、生产、测试等行业提供了新的选择。
前面板、后面板和用户界面（显示屏）的简要介绍请分别参考图 1、图 2和图 3。
图1前面板
1 2 3 4 5 6 7 8
14 13 12 11 10 9

4
表1 前面板说明
编号
说明
编号
说明
1
电源键
8
频率计
2
USB HOST
9
方向键
3
同相位键
10
旋钮
4
CH1 输出连接器
11
Shift 键
5
通道控制区
12
Home/Menu 键
6
CH2 输出连接器
13
功能键
7
Counter 测量信号输入连接器
14
LCD 触摸显示屏
图2后面板
表2 后面板说明
编号
说明
编号
说明
1
10MHz 输入/输出连接器
4
USB DEVICE
2
CH1 同步/外调制/触发连接器
5
AC 电源插口
3
CH2 同步/外调制/触发连接器
6
LAN
图3用户界面
1 2 3 4 5 6
8
9
10
11
1 2 3
7 6 5 4

5
表3 用户界面标识
编号
名称
说明
1
通道输出配置
状态栏
显示各通道当前的输出配置。
2
上下滑动条
提示用户可上下滑动屏幕，查看或设置参数。
3 信息设置
：打开 Store 界面。
：打开 Utility 界面。
：执行通道复制功能。
：执行屏幕打印操作。
4
右箭头
提示用户可向右滑动屏幕，切换至波形选择界面。
5 状态栏
：表示前面板按键和屏幕被锁定。
：表示关闭蜂鸣器。
：表示仪器处于程控模式。
：表示使用网线成功将仪器连接至局域网。
：表示成功连接
U
盘。
6
波形
显示各通道当前选择的波形。
7
界面标签
显示当前界面的标签。
8
频率
显示各通道当前波形的频率。
9
幅度
显示各通道当前波形的幅度。
10
偏移
显示各通道当前波形的直流偏移。
11
相位
显示各通道当前波形的相位。
使用前准备
连接电源
请使用附件提供的电源线将信号发生器连接至 AC 电源中，如下图所示。本信号发生器支持
100-127V，45-440Hz 或100-240V，45-65Hz 规格的交流电源，最大输入功率不超过 30W。当通
过该连接器将信号发生器连接到交流电源时，仪器自动调节至正确的电压范围，无需手动选择电
压范围。
注意
为避免电击，请确保仪器正确接地。
开机检查
正确连接电源后，按下前面板的电源键 打开信号发生器。开机过程中仪器执行初始化过程和
自检过程。结束后，屏幕进入默认界面。

6
设置系统语言
DG2000 支持多种语言菜单。在 Shift 键背灯变亮状态，您可以按 Pulse/Utility系统设置，
然后触摸点击 Language 标签右侧的参数选择框，选择所需的语言类型。
使用内置帮助系统
DG2000 对于前面板上的每个功能按键以及当前显示界面都提供了帮助信息。用户可在操作仪器
的过程中随时查看各项帮助信息。
1. 获取前面板按键帮助
在Shift 键背灯变亮状态，按下 Arb/Help/Local 键，然后再按下你所需要获得帮助的前面
板按键，仪器界面显示该键的帮助信息。
2. 获取常用帮助主题
在Shift 键背灯变亮状态，按下前面板 Arb/Help/Local 键，弹出如下图所示的界面，触摸
点击屏幕中“帮助”，进入帮助列表界面。此时，您可通过上下滑动屏幕或旋转旋钮滚动列表，
然后触摸点击选中相应的帮助项，仪器界面显示该项的帮助信息。
3. 获取界面数据说明
在Shift 键背灯变亮状态，按下前面板 Arb/Help/Local 键，弹出界面如上图所示。然后触
摸点击屏幕“中间”，可显示对当前界面中间部分数据的解释说明；触摸点击“顶部”，可显示
对当前界面上部分数据的解释说明；触摸点击“底部”，可显示对当前界面下部分数据的解释
说明；触摸点击“向导”，可进入向导界面提示您进行操作。
4. 帮助的翻页操作
当帮助信息为多页显示时，您可通过手指上下滑动屏幕以滚动帮助信息页面。
5. 关闭当前的帮助信息
当仪器界面显示帮助信息时，用户按下前面板 Arb/Help/Local 键，将关闭当前显示的帮助
信息。
实例：输出正弦波
本节主要介绍如何从[CH1] 连接器输出一个正弦波（频率为 20kHz，幅度为 2.5Vpp，偏移量为
500mVdc，起始相位为 90°）。
1. 选择输出通道：按下前面板 Output1 键（或通过触摸点击通道输出配置状态栏 ）
选中 CH1 通道。此时通道界面以红色显示。
2. 选择正弦波：在Shift 键背灯变亮状态，按下前面板 Home/Menu 键，在弹出的波形选择
界面触摸点击 Continuous“Sine”图标，（或在Shift 键背灯熄灭状态，按下前面板

7
Sine/Preset 键 ，） 仪器自动跳转至正弦波参数设置界面。
3. 设置频率：触摸点击频率标签右侧的参数输入框，通过弹出的数字键盘输入 20，选择单位
“kHz”，点击“Ok”。
4. 设置幅度：触摸点击幅度标签右侧的参数输入框，通过弹出的数字键盘输入 2.5，选择单位
“Vpp”，点击“Ok”。
5. 设置偏移电压：触摸点击偏移标签右侧的参数输入框，通过弹出的数字键盘输入 500，选 择单
位“mVdc”，点击“Ok”。
6. 设置起始相位：触摸点击相位标签右侧的参数输入框，通过弹出的数字键盘输入 90，选择单
位“°”，点击“Ok”。
7. 启用通道输出：按Output1 键（ 或通过触摸点击通道输出配置状态栏 ，在通道设
置界面打开通道输出），Output1 键背灯点亮并且通道状态条呈高亮状态（即 ），
[CH1]连接器以当前配置输出正弦波信号。
8. 观察输出波形：使用 BNC 连接线将 DG2000 的[CH1]与示波器相连接，由示波器观察输出波
形。
远程控制
DG2000 系列函数/任意波形发生器可以通过 USB、LAN 或GPIB（配合 RIGOL 的USB-GPIB转接
模块）接口与计算机进行通信从而实现远程控制。远程控制基于 SCPI（Standard Commands for
Programmable Instruments）命令集实现。DG2000 支持两种远程控制方式：用户自定义编程和
使用 PC 软件（如 RIGOL Ultra Sigma）。
当仪器处于远程控制状态时，前面板按键以及触摸屏被锁定（电源开关键 和
Arb/Help/Local 键除外）。此时，在 Shift 键背灯变亮状态，您可以按 Arb/Help/Local 退
出远程模式。
更多产品信息
1. 获取设备信息
在Shift 键背灯变亮状态，按 Pulse/Utility系统信息，您可获取设备信息，包括设备型
号、设备序列号以及软件版本号。
2. 查看选件安装状态
在Shift 键背灯变亮状态，按 Pulse/Utility选件，您可查看所有选件的安装状态。
欲了解本产品更多信息，请查阅相关手册（您可登录RIGOL网站www.rigol.com下载）。
《DG2000用户手册》：提供本产品的功能介绍及操作方法、远程控制方法、在使用过程中可能出
现的故障及处理方法以及订货信息；
《DG2000编程手册》：提供本产品的SCPI命令集以及编程实例；
《DG2000数据手册》：提供本产品的主要特色和技术指标。

1
Guaranty and Declaration
Copyright
© 2019 RIGOL (SUZHOU) TECHNOLOGIES INC. All Rights Reserved.
TrademarkInformation
RIGOL is a registered trademark of RIGOL (SUZHOU) TECHNOLOGIES INC.
PublicationNumber
QGB12100-1110
Notices
RIGOL products are covered by P.R.C. and foreign patents, issued and pending.
RIGOL reserves the right to modify or change parts of or all the specifications and pricing
policies at the company’s sole decision.
Information in this publication replaces all previously released materials.
Information in this publication is subject to change without notice.
RIGOL shall not be liable for either incidental or consequential losses in connection with the
furnishing, use, or performance of this manual, as well as any information contained.
Any part of this document is forbidden to be copied, photocopied, or rearranged without prior
written approval of RIGOL.
ProductCertification
RIGOL guarantees that this product conforms to the national and industrial standards in China
as well as the ISO9001:2015 standard and the ISO14001:2015 standard. Other international
standard conformance certifications are in progress.
ContactUs
If you have any problem or requirement when using our products or this manual, please contact
RIGOL.
E-mail: [e-mail]
Website: www.rigol.com
General Safety Summary
1. Only the exclusive power cord designed for
the instrument and authorized for use
within the local country could be used.
2. Ensure that the instrument is safely
grounded.
3. Observe all terminal ratings.
4. Use proper overvoltage protection.
5. Do not operate without covers.
6. Do not insert objects into the air outlet.
7. Use the proper fuse.
8. Avoid circuit or wire exposure.
9. Do not operate the instrument with
suspected failures.
10.Provide adequate ventilation.
11.Do not operate in wet conditions.
12.Do not operate in an explosive
atmosphere.
13.Keep instrument surfaces clean and dry.
14.Prevent electrostatic impact.
15.Handle with caution.
16.Please use the front-panel BNC output
connector correctly. It is only allowed to
output signal.
Safety Notices and Symbols
Safety Notices in this Manual:
WARNING
Indicates a potentially hazardous situation or practice which, if not avoided, will
result in serious injury or death.

2
CAUTION
Indicates a potentially hazardous situation or practice which, if not avoided,
could result in damage to the product or loss of important data.
SafetyTerms on the Product:
DANGER
It calls attention to an operation, if not correctly performed, could result in
injury or hazard immediately.
WARNING
It calls attention to an operation, if not correctly performed, could result in
potential injury or hazard.
CAUTION
It calls attention to an operation, if not correctly performed, could result in
damage to the product or other devices connected to the product.
Safety Symbols on the Product:
Hazardous
Voltage
Safety
Warning
Protective Earth
Terminal
Chassis Ground
Test Ground
Care and Cleaning
Care
Do not store or leave the instrument where it may be exposed to direct sunlight for long periods
of time.
Cleaning
Clean the instrument regularly according to its operating conditions.
1. Disconnect the instrument from all power sources.
2. Clean the external surfaces of the instrument with a soft cloth dampened with mild detergent
or water. Avoid having any water or other objects into the chassis via the heat dissipation
hole.When cleaning the LCD, take care to avoid scarifying it.
CAUTION
To avoid damage to the instrument, do not expose it to caustic liquids.
WARNING
To avoid short-circuit resulting from moisture or personal injuries, ensure that
the instrument is completely dry before connecting it to the power supply.
Document Overview
This manual introduces some basic information that you should know when you use the DG2000
series function/arbitrary waveform generator for the first time. It contains the following contents:
product overview, how to connect the instrument to the AC power, turn-on checkout, and
remote control.
Tip
For the latest version of this manual, download it from the official website of RIGOL
(www.rigol.com).

3
Format Conventions in this Manual
1. Keys:
The keys on the front panel are usually denoted by the format of "Key Name (Bold) + Text
Box". For example, Pulse/Utility.
2. Menu Labels:
The menu labels are usually denoted by the format of "Menu Word (Bold) + Character
Shading". For example, System Setting.
3. Connectors:
The connectors on the front or rear panel are usually denoted by the format of "Connector
Name (Bold) + Square Brackets (Bold)". For example, [Counter].
4. Operation Procedures:
"" represents the next step of operation. For example, when the backlight of the Shift key
is illuminated, pressing Pulse/Utility System Setting indicates that first press
Pulse/Utility on the front panel and then tap the menu label System Setting.
Content Conventions in this Manual
DG2000 series function/arbitrary waveform generator includes the following models. Unless
otherwise specified, this manual takes DG2102 as an example to illustrate the operation
methods of the DG2000 series.
Model
No. of Channels
Max. Output Frequency
DG2052
2
50 MHz
DG2072
2
70 MHz
DG2102
2
100 MHz
General Inspection
1. Inspect the packaging
If the packaging has been damaged, do not dispose the damaged packaging or cushioning
materials until the shipment has been checked for completeness and has passed both
electrical and mechanical tests.
The consigner or carrier shall be liable for the damage to the instrument resulting from
shipment. RIGOL would not be responsible for free maintenance/rework or replacement of
the instrument.
2. Inspect the instrument
In case of any mechanical damage, missing parts, or failure in passing the electrical and
mechanical tests, contact your RIGOL sales representative.
3. Check the accessories
Please check the accessories according to the packing lists. If the accessories are damaged or
incomplete, please contact your RIGOL sales representative.
Product Overview
As a multi-functional signal generator, DG2000 series function/arbitrary waveform generator
integrates many instruments into 1, such as function generator, arbitrary waveform generator,
noise generator, pulse generator, harmonic generator, analog/digital modulator, and frequency
counter. As a multi-functional and portable instrument, it offers you a new choice in education,

4
R&D, production, measurement, and other industries with its user-friendly touch screen and
high performance at an unprecedented price point.
For descriptions of the front panel, refer to Figure 1; for descriptions of the rear panel, refer to
Figure 2; and for descriptions of the user interface (LCD), refer to Figure 3.
Figure 1 Front Panel
Table 1 Front Panel Description
No.
Description
No.
Description
1
Power Key
8
Frequency Counter
2
USB HOST
9
Arrow Keys
3
Align Phase Key
10
Knob
4
CH1 Output Connector
11
Shift Key
5
Channel Control Area
12
Home/Menu Key
6
CH2 Output Connector
13
Function Keys
7
Counter Measurement Signal
Input Connector
14
LCD Touch Screen
Figure 2 Rear Panel
1 2 3 4 5 6
1 2 3 45 6 7 8
14 13 12 11 10 9

5
Table 2 Rear Panel Description
No.
Description
No.
Description
1
10MHz In/Out Connector
4
USB DEVICE
2
CH1 Sync/Ext Mod/Trig/FSK Connector
5
AC Power Cord Connector
3
CH2 Sync/Ext Mod/Trig/FSK Connector
6
LAN
Figure 3 User Interface
Table 3 User Interface Icons
No.
Name
Description
1
Channel Output
Configuration
Status Bar
Displays the current output configuration of the channel.
2
Up and Down
Scroll Bar
Prompts you to move up and down with your fingers on the
screen to view and set parameters.
3 Information
Setting
: opens the Store interface.
: opens the Utility interface.
: performs the channel copy function.
: performs the screen print operation.
4 Right Arrow
Prompts you to slide right on the screen to switch to the
waveform selection interface.
5 Status Bar
: indicates that the front-panel keys and the screen are
locked.
: indicates that the beeper is disabled.
: indicates that the instrument is in programming-controlled
mode.
: indicates that the instrument has been successfully
connected to the local area network by using the network
cable.
: indicates that a USB storage device is found.
6
Waveform
Displays the currently selected waveform of each channel.
7
Interface
Label
Displays the label of the current interface.
8 Frequency
Displays the frequency of the current waveform of each
channel.
9
Amplitude
Displays the amplitude of the current waveform of each
8
9
10
11
1 2 3
7 6 5 4

6
channel.
10
Offset
Displays the DC offset of the current waveform of each channel.
11
Phase
Displays the phase of the current waveform of each channel.
To Prepare for Use
To Connect to AC Power
Please use the power cord provided in the accessories to connect the signal generator to the AC
power source, as shown in the figure below. The rated AC power source supported by the signal
generator is (100-127 V, 45-440Hz) or (100-240 V, 45-65Hz), and its maximum input power shall
not exceed 30 W. When the signal generator is connected to the AC power source via the power
cord, the instrument automatically adjusts itself to within the proper voltage range, and you do
not need to select the voltage range manually.
CAUTION
To avoid electric shock, ensure that the instrument is correctly grounded.
Turn-on Checkout
After connecting the instrument to the power source properly, press on the front panel to
start the signal generator. During the start-up, the instrument will undergo the initialization and
self-check process. Then, it will enter a default interface.
To Set the System Language
DG2000 arbitrary waveform generator supports multiple languages. Press the Shift key and its
backlight turns on, and then press Pulse/UtilitySystem Setting, and then select a desired
language from the Language drop-down list.
To Use the Built-in Help System
DG2000 series provides the help information for each front-panel function menu and the current
display interface. You can view the help information if you have any questions during the
operation process.
1. Obtain the help information of the front panel keys
Press the Shift key and its backlight turns on. Then press Arb/Help/Local first, and then
press the desired key for the help information. Then, the corresponding help information is
displayed.

7
2. Obtain the common help topics
Press the Shift key and its backlight turns on. Press Arb/Help/Local on the front panel,
and then the following interface is displayed below. Tap "Help" to enter the help interface. At
this time, you can tap on the touch screen to move up and down the help items or rotate the
knob to scroll up and down the list to select the desired help item. Then, the help information
for the item is displayed in the interface.
3. Obtain the descriptions of the data in the interface
Press the Shift key and its backlight turns on. Press Arb/Help/Local on the front panel to
enter the interface, as shown above. Tap "Center" to view the descriptions for the data in
the center of the current interface. Tap "Top" to view the descriptions for the data in the top
part of the current interface. Tap "Bottom" to view the descriptions for the data in the
bottom part of the current interface. Tap "Guide" to enter the guide interface.
4. Page up/down operation
When the help information is displayed in multiple pages, you can tap to move up and down
the touch screen to view the help information.
5. Close the current help information
When the help information is displayed in the interface, press Arb/Help/Local on the front
panel to close the help information currently displayed on the screen.
Example: To Output Sine
This section mainly introduces how to output Sine waveforms (frequency 20 kHz, amplitude 2.5
Vpp, offset 500 mVdc, start phase 90°) from the [CH1] connector.
1. Select the output channel: Press Output1on the front panel or tap the channel output
configuration status bar to select CH1. At this time, the channel is indicated in
red in the status bar.
2. Select Sine waveforms: Press the Shift key and its backlight turns on. Press
Home/Menu on the front panel, and then the waveform selection interface is displayed.
Tap Continuous and then select the "Sine" icon to go to the sine waveform parameter
setting interface automatically.
3. Set frequency: Tap the Freq parameter input field to input 20 with the pop-up numeric
keypad, and then select "kHz" as the unit. Tap "Ok".
4. Set amplitude: Tap the Ampl parameter input field to input 2.5 with the pop-up numeric
keypad, and then select "Vpp" as the unit. Tap "Ok".

8
5. Set offset voltage: Tap the Offset parameter input field to input 500 with the pop-up
numeric keypad, and then select "mVdc" as the unit. Tap "Ok".
6. Set start phase: Tap the Phase parameter input field to input 90 with the pop-up numeric
keypad, and then select "°" as the unit. Tap "Ok".
7. Enable channel output: Press Output1 or tap the channel output configuration status
bar to enable the channel output. Then, the backlight of Output1 key is
illuminated and the channel status is highlighted ( ), and the Sine signal is output
from the [CH1] connector based on the current configurations.
8. Observe the output waveforms: Connect the [CH1] connector of the DG2000 series to
the oscilloscope by using the BNC cable, and then you can view the output waveforms from
the oscilloscope.
Remote Control
DG2000 series function/arbitrary waveform generator can be connected to the PC via the USB,
LAN or GPIB (working with RIGOL USB-GPIB interface converter) to realize remote control. The
remote control can be realized by using SCPI (Standard Commands for Programmable
Instruments) commands. DG2000 series signal generator supports two ways of remote control:
user-defined programming and PC software (e.g. RIGOL Ultra Sigma).
When the instrument is in remote control, the front panel keys (except the Power key and
Arb/Help/Local key) and the touch screen are locked. At this time, press the Shift key and its
backlight turns on. Then you can press Arb/Help/Local to exit the remote mode.
More Product Information
1. Obtain the device information
Press the Shift key and its backlight turns on. Press Pulse/UtilitySystem Info to obtain
the information of the instrument, including the device model, device serial number, as well
as software version number.
2. Check the option installation
Press the Shift key and its backlight turns on. Press Pulse/UtilityOption to view the
installation status of all the options.
For more information about this instrument, refer to the relevant manuals by logging in to the
official website of RIGOL (www.rigol.com) to download them.
DG2000 User Guide : introduces the functions of the instrument and the operation methods,
remote control methods, possible failures and solutions in using the instrument, and order
information;
DG2000 Programming Guide : provides detailed descriptions of SCPI commands and
programming instances of the instrument.
DG2000 Datasheet : provides the main features and technical specifications of the instrument.