Rigol DSG3000 Series User manual

RIGOL
User’s Guide
DSG3000 Series RF Signal Generator
Nov. 2013
RIGOL Technologies, Inc.

RIGOL
DSG3000 User’s Guide I
Guaranty and Declaration
Copyright
© 2013 RIGOL Technologies, Inc. All Rights Reserved.
Trademark I nformation
RIGOL is a registered trademark of RIGOL Technologies, Inc.
Publication Number
UGG01106-1110
Notices
RIGOL products are protected by patent law in and outside of P.R.C.
RIGOL reserves the right to modify or change parts of or all the specifications
and pricing policies at company’s sole decision.
Information in this publication replaces all previously corresponding material.
RIGOL shall not be liable for losses caused by either incidental or consequential
in connection with the furnishing, use or performance of this manual as well as
any information contained.
Any part of this document is forbidden to be copied or photocopied or
rearranged without prior written approval of RIGOL.
Product Certification
RIGOL guarantees this product conforms to the national and industrial standards in
China as well as the ISO9001:2008 standard and the ISO14001:2004 standard.
Other international standard conformance certification is in progress.
Contact Us
If you have any problem or requirement when using our products or this manual,
please contact RIGOL.
E-mail: [e-mail]
Websites: www.rigol.com

RIGOL
II DSG3000 User’s Guide
Safety Requirement
General Safety Summary
Please review the following safety precautions carefully before putting the
instrument into operation so as to avoid any personal injury or damage to the
instrument and any product connected to it. To prevent potential hazards, please use
the instrument only specified by this manual.
Use Proper Power Cord.
Only the power cord designed for the instrument and authorized for use within the
local country should be used.
Ground The I nstrument.
The instrument is grounded through the Protective Earth lead of the power cord. To
avoid electric shock, it is essential to connect the earth terminal of power cord to the
Protective Earth terminal before connecting any inputs or outputs.
Connect the Probe Correctly.
If a probe is used, do not connect the ground lead to high voltage since it has the
isobaric electric potential as ground.
Observe All Terminal Ratings.
To avoid fire or shock hazard, observe all ratings and markers on the instrument and
check your manual for more information about ratings before connecting.
Use Proper Overvoltage Protection.
Make sure that no overvoltage (such as that caused by a thunderstorm) can reach
the product, or else the operator might expose to danger of electrical shock.
Do Not Operate Without Covers.
Do not operate the instrument with covers or panels removed.
Do Not I nsert Anything into the Holes of Fan.
Do not insert anything into the holes of the fan to avoid damaging the instrument.
Use Proper Fuse.
Please use the specified fuses.
Avoid Circuit or Wire Exposure.
Do not touch exposed junctions and components when the unit is powered.
Do Not Operate With Suspected Failures.
If you suspect damage occurs to the instrument, have it inspected by qualified

RIGOL
DSG3000 User’s Guide III
service personnel before further operations. Any maintenance, adjustment or
replacement especially to circuits or accessories must be performed by RIGOL
authorized personnel.
Keep Well Ventilation.
Inadequate ventilation may cause increasing of temperature or damages to the
device. So please keep well ventilated and inspect the intake and fan regularly.
Do Not Operate in Wet Conditions.
In order to avoid short circuiting to the interior of the device or electric shock, please
do not operate in a humid environment.
Do Not Operate in an Explosive Atmosphere.
In order to avoid damages to the device or personal injuries, it is important to
operate the device away from an explosive atmosphere.
Keep Product Surfaces Clean and Dry.
To avoid the influence of dust and/ or moisture in air, please keep the surface of the
device clean and dry.
Electrostatic Prevention.
Operate in an electrostatic discharge protective area environment to avoid damages
induced by static discharges. Always ground both the internal and external
conductors of the cable to release static before connecting.
Proper Use of Battery.
If a battery is supplied, it must not be exposed to high temperature or in contact with
fire. Keep it out of the reach of children. Improper change of battery (note: lithium
battery) may cause explosion. Use RIGOL specified battery only.
Do Not Overload the Output.
In order to avoid damage to the instrument, the reverse DC voltage on the RF output
connector cannot exceed 50 V; the reverse power must be less than + 40 dBm (10 W)
in the frequency range from 1 MHz to 6 GHz.
Handling Safety.
Please handle with care during transportation to avoid damage to buttons, knob
interfaces and other parts on the panels.

RIGOL
IV DSG3000 User’s Guide
Safety Terms and Symbols
Terms Used in this Manual. These terms may appear in this manual:
WARNI NG
Warning statements indicate the conditions or practices that could result in
injury or loss of life.
CAUTI ON
Caution statements indicate the conditions or practices that could result in
damage to this product or other property.
Terms Used on the Product. These terms may appear on the Product:
DANGER
indicates an injury or hazard may immediately happen.
WARNI NG
indicates an injury or hazard may be possible.
CAUTI ON
indicates potential damage to the instrument or other.
Symbols Used on the Product. These symbols may appear on the product:
Hazardous
Voltage
Safety
Warning
Protective
Earth
Terminal
Chassis
Ground
Test
Ground

RIGOL
DSG3000 User’s Guide V
Allgemeine Sicherheits I nformationen
Überprüfen Sie diefolgenden Sicherheitshinweise
sorgfältigumPersonenschädenoderSchäden am Gerätundan damit verbundenen
weiteren Gerätenzu vermeiden.Zur Vermeidung vonGefahren, nutzen Sie bitte das
Gerät nur so, wiein diesem Handbuchangegeben.
Um Feuer oder Verletzungen zu vermeiden, verwenden Sie ein
ordnungsgemäßes Netzkabel.
Verwenden Sie für dieses Gerät nur das für ihr Land zugelassene und genehmigte
Netzkabel.
Erden des Gerätes.
Das Gerät ist durch den Schutzleiter im Netzkabel geerdet. Um Gefahren durch
elektrischen Schlag zu vermeiden, ist es unerlässlich, die Erdung durchzuführen. Erst
dann dürfen weitere Ein- oder Ausgänge verbunden werden.
Anschluss einesTastkopfes.
Die Erdungsklemmen der Sonden sindauf dem gleichen Spannungspegel des
Instruments geerdet. SchließenSie die Erdungsklemmen an keine hohe Spannung
an.
Beachten Sie alle Anschlüsse.
Zur Vermeidung von Feuer oder Stromschlag, beachten Sie alle Bemerkungen und
Markierungen auf dem Instrument. Befolgen Sie die Bedienungsanleitung für weitere
Informationen, bevor Sie weitere Anschlüsse an das Instrument legen.
Verwenden Sie einen geeigneten Überspannungsschutz.
Stellen Sie sicher, daß keinerlei Überspannung (wie z.B. durch Gewitter verursacht)
das Gerät erreichen kann. Andernfallsbestehtfür den Anwender die
GefahreinesStromschlages.
Nicht ohne Abdeckung einschalten.
Betreiben Sie das Gerät nicht mit entfernten Gehäuse-Abdeckungen.
Betreiben Sie das Gerät nicht geöffnet.
Der Betrieb mit offenen oder entfernten Gehäuseteilen ist nicht zulässig. Nichts in
entsprechende Öffnungen stecken (Lüfter z.B.)
Passende Sicherung verwenden.
Setzen Sie nur die spezifikationsgemäßen Sicherungen ein.
Vermeiden Sie ungeschützte Verbindungen.
Berühren Sie keine unisolierten Verbindungen oder Baugruppen, während das Gerät
in Betrieb ist.

RIGOL
VI DSG3000 User’s Guide
Betreiben Sie das Gerät nicht im Fehlerfall.
Wenn Sie am Gerät einen Defekt vermuten, sorgen Sie dafür, bevor Sie das Gerät
wieder betreiben, dass eine Untersuchung durch qualifiziertes Kundendienstpersonal
durchgeführt wird.Jedwede Wartung, Einstellarbeiten oder Austausch von Teilen am
Gerät, sowie am Zubehör dürfen nur von RI GOL autorisiertem Personal
durchgeführt werden.
Belüftung sicherstellen.
Unzureichende Belüftung kann zu Temperaturanstiegen und somit zu thermischen
Schäden am Gerät führen. Stellen Sie deswegen die Belüftung sicher und
kontrollieren regelmäßig Lüfter und Belüftungsöffnungen.
Nicht in feuchter Umgebung betreiben.
Zur Vermeidung von Kurzschluß im Geräteinneren und Stromschlag betreiben Sie das
Gerät bitte niemals in feuchter Umgebung.
Nicht in explosiver Atmosphäre betreiben.
Zur Vermeidung von Personen- und Sachschäden ist es unumgänglich, das Gerät
ausschließlich fernab jedweder explosiven Atmosphäre zu betreiben.
Geräteoberflächen sauber und trocken halten.
Um den Einfluß von Staub und Feuchtigkeit aus der Luft auszuschließen, halten Sie
bitte die Geräteoberflächen sauber und trocken.
Schutz gegen elektrostatische Entladung (ESD).
Sorgen Sie für eine elektrostatisch geschützte Umgebung, um somit Schäden und
Funktionsstörungen durch ESD zu vermeiden. Erden Sie vor dem Anschluß immer
Innen- und Außenleiter der Verbindungsleitung, um statische Aufladung zu entladen.
Die richtige Verwendung desAkku.
Wenneine Batterieverwendet wird, vermeiden Sie hohe Temperaturen bzw. Feuer
ausgesetzt werden.Bewahren Sie es außerhalbder Reichweitevon Kindern
auf.UnsachgemäßeÄnderung derBatterie(Anmerkung:Lithium-Batterie)kann zu einer
Explosion führen. VerwendenSie nur von RI GOLangegebenenAkkus.
Sicherer Transport.
Transportieren Sie das Gerät sorgfältig (Verpackung!), um Schäden an
Bedienelementen, Anschlüssen und anderen Teilen zu vermeiden.

RIGOL
DSG3000 User’s Guide VII
Sicherheits Begriffe und Symbole
Begriffe in diesem Guide. Diese Begriffe können in diesem Handbuch
auftauchen:
WARNI NG
Die Kennzeichnung WARNING beschreibt Gefahrenquellen die leibliche
Schäden oder den Tod von Personen zur Folge haben können.
CAUTI ON
Die Kennzeichnung Caution (Vorsicht) beschreibt Gefahrenquellen die
Schäden am Gerät hervorrufen können.
Begriffe auf dem Produkt. Diese Bedingungen können auf dem Produkt
erscheinen:
DANGER
weist auf eine Verletzung oder Gefährdung hin, die sofort
geschehen kann.
WARNI NG
weist auf eine Verletzung oder Gefährdung hin, die möglicherweise
nicht sofort geschehen.
CAUTI ON
bedeutet, dass eine mögliche Beschädigung des Instruments oder
anderer Gegenstände auftreten kann.
Symbole auf dem Produkt. Diese Symbole können auf dem Produkt
erscheinen:
GefährlicheS
pannung
Sicherheits-
Hinweis Schutz-erde Gehäusemasse Erde

RIGOL
VIII DSG3000 User’s Guide
General Care and Cleaning
General Care:
Do not store or leave the instrument where it may be exposed to direct sunlight for
long periods of time.
Cleaning:
Clean the instrument regularly according to its operating conditions. To clean the
exterior surface, perform the following steps:
1. Disconnect the instrument from all power sources.
2. Clean the loose dust on the outside of the instrument with a lint-free cloth (with
a mild detergent or water). When cleaning the LCD, take care to avoid
scratching it.
CAUTI ON
To avoid damage to the instrument, do not expose to caustic liquids.
WARNI NG
To avoid injury resulting from a short circuit, make sure the instrument is
completely dry before reconnecting to a power source.
Environmental Considerations
The following symbol indicates that this product complies with the applicable
European Union requirements according to Directives 2002/96/ EC on waste electrical
and electronic equipment (WEEE) and batteries.
Product End-of-Life Handling
The equipment may contain substances that could be harmful to the environment or
human health. In order to avoid release of such substances into the environment and
harm to human health, we encourage you to recycle this product in an appropriate
system that will ensure that most of the materials are reused or recycled
appropriately. Please contact your local authorities for disposal or recycling
information.

RIGOL
DSG3000 User’s Guide IX
DSG3000 Series Overview
The DSG3000 series is a high-performance RF signal generator. It provides
comprehensive modulation solutions such as: pulse modulation with customizable
pulse train and I / Q modulation (optional), and standard AM/ FM/
Φ M analog
modulation. All modulation schemes support internal and external modulation
sources. In addition, to meet the demands of production environments, the DSG3000
is designed to be both highly stable and reliable. The DSG3000 series also features a
clear user interface, small size and light weight. It is easy to operate and can output
stable, precise and pure signals. It is an ideal tool for various f ields such as
communication, computers, instrumentation, R&D, education, production and
maintenance.
Main Features:
The highest frequency: 3 GHz/ 6 GHz
Amplitude accuracy: < 0.5dB (typical)
Output amplitude range: -130 dBm to + 13 dBm
High signal purity, phase noise: < -110dBc/Hz@20kHz (typical)
Standard 0.5ppm internal clock; 5ppb high stable clock for option
Standard AM/FM/
Φ M analog modulation
Standard pulse modulation; on/off ratio up to 80dB; pulse train generator
(optional)
I/Q modulation and I/Q baseband output
All modulation schemes support internal and external modulation modes
Standard 2U height design to save rack space. Rack mount kit is available
Standard USB/LAN/GPIB remote control interfaces. SCPI command set for
remote control
Wear-free electronic attenuator design
Well-designed automatic flatness calibration function (Cables, attenuators,
amplifiers and so on) for test systems with power meter control

RIGOL
X DSG3000 User’s Guide
Document Overview
Main contents in this manual
Chapter 1 Quick Start
This chapter introduces the front panel, rear panel and user interface of the RF signal
generator as well as the precautions when using the instrument for the first time.
Chapter 2 Front Panel Operations
This chapter describes the front panel function keys of the RF signal generator and
introduces the menu functions under each key in details.
Chapter 3 Remote Control
This chapter introduces the remote control method of RF signal generator.
Chapter 4 Application Examples
This chapter describes intuitively RF signal generator with operation examples.
Chapter 5 Troubleshooting
This chapter lists commonly encountered failures that may appear during the use of
the RF signal generator and their solutions.
Chapter 6 Specifications
This chapter lists the performances and general specifications of the instrument.
Chapter 7 Appendix
This chapter provides the information about the options and accessories, as well as
other points for attention.

RIGOL
DSG3000 User’s Guide XI
Format Conventions in this Manual
1. Button:
The key at the front panel is denoted by the following format: “Tex t Box +
Button Name (Bold)” in the manual, for example, FREQ denotes the FREQ key.
2. Menu:
The menu is denoted by the following format: “Character Shading + Menu Word
(Bold)” in the manual, for example, Frequency denotes the frequency item
under FREQ.
3. Connector:
The connector at the front or rear panel is denoted by the following format:
“Square Brackets + Connector Name (Bold)” in the manual, for example, [RF
OUTPUT 50Ω].
4. Operation Steps:
The next step of the operation is denoted by an arrow “” in the manual. For
example, FREQ Frequency denotes pressing FREQ on the front panel and
then pressing Frequency.
Content Conventions in this Manual
The DSG3000 series RF signal generator includes the modes DSG3030 and DSG3060.
The illustrations in this manual are based on DSG3060.
Model
Frequency Range
DSG3030
9kHz ~ 3GHz
DSG3060
9kHz ~ 6GHz
Manuals of this Product
The manuals of this product include the quick guide, user’s guide, programming
guide and data sheet. The latest versions of the manuals can be downloaded from
www.rigol.com.

RIGOL
XII DSG3000 User’s Guide
Contents
Guaranty and Declaration......................................................................... I
Safety Requirement.................................................................................I I
General Safety Summary........................................................................... II
Safety Terms and Symbols ....................................................................... IV
Allgemeine Sicherheits Informationen ........................................................ V
Sicherheits Begriffe und Symbole............................................................. VII
General Care and Cleaning .....................................................................VII I
Environmental Considerations.................................................................VIII
DSG3000 Series Overview ...................................................................... I X
Document Overview ................................................................................ X
Chapter 1 Quick Start ........................................................................ 1-1
General Inspection .................................................................................1-2
Appearance and Dimensions ...................................................................1-3
Front Panel Overview .............................................................................1-5
Rear Panel Overview ............................................................................1-12
To Use DSG3000 for the First Time ........................................................1-17
To Connect the Power Supply..........................................................1-17
Power-on I nspection ......................................................................1-18
To Set the System Language...........................................................1-18
To Replace the Fuse .............................................................................1-19
User Interface......................................................................................1-20
Normal Display Mode .....................................................................1-20
Parameter Zoom-in Mode ...............................................................1-23
To Use the Built-in Help System .............................................................1-24
Chapter 2 Front Panel Operations...................................................... 2-1
To Set the Frequency Parameters.............................................................2-2
Frequency.......................................................................................2-2
Frequency Offset .............................................................................2-2
Phase Offset ...................................................................................2-3
To Set the Amplitude Parameters.............................................................2-4
Amplitude .......................................................................................2-4
Amplitude Limit ...............................................................................2-4
Amplitude Offset..............................................................................2-5
Attenuation Mode ............................................................................2-6
Attenuation .....................................................................................2-6
ALC................................................................................................2-7
Hold Mode ......................................................................................2-7
Flatness Calibration..........................................................................2-7
Amplitude Unit ................................................................................2-9
Sweep................................................................................................. 2-10

RIGOL
DSG3000 User’s Guide XIII
Sweep Manner...............................................................................2-10
Sweep Direction.............................................................................2-10
Sweep Type...................................................................................2-11
Sweep Mode..................................................................................2-15
Single Sweep.................................................................................2-16
Reset Sweep .................................................................................2-16
Trigger Mode .................................................................................2-16
Modulation ..........................................................................................2-19
Amplitude Modulation (AM) .............................................................2-19
Frequency Modulation (FM).............................................................2-22
Phase Modulation (
Φ M) ..................................................................2-24
Pulse Modulation ...........................................................................2-26
I/Q Modulation (Option IQ-DSG3000) ..............................................2-34
LF Output ............................................................................................2-39
To Enable the LF Output .................................................................2-39
To Set the LF Parameters................................................................2-39
Power Meter (Option PMC-DSG3000)......................................................2-44
To Enable the Power Meter .............................................................2-44
Ze r o Ty p e ......................................................................................2-45
Zero .............................................................................................2-45
Frequency Mode ............................................................................2-45
Frequency .....................................................................................2-45
Average Measurement ....................................................................2-46
Preset ...........................................................................................2-46
Limit Measurement ........................................................................2-46
Recorder .......................................................................................2-48
Relative Measurement ....................................................................2-49
Statistics .......................................................................................2-49
Unit ..............................................................................................2-50
System Information........................................................................2-50
RX1000 (Option) ..................................................................................2-51
Store and Recall ...................................................................................2-52
File Type .......................................................................................2-52
Save.............................................................................................2-54
Recall ...........................................................................................2-57
Rename ........................................................................................2-57
Delete...........................................................................................2-58
Copy.............................................................................................2-58
To Create a Directory .....................................................................2-58
Filename Prefix..............................................................................2-59
Disk Management ..........................................................................2-59
System Update ..............................................................................2-59
To Set the System Parameters ...............................................................2-60
Language......................................................................................2-60
Reset ............................................................................................2-60
I/O Configuration...........................................................................2-61

RIGOL
XIV DSG3000 User’s Guide
Display Setting ..............................................................................2-63
Power Status.................................................................................2-63
Information...................................................................................2-63
License.........................................................................................2-64
Self-test ........................................................................................2-65
Sanitation .....................................................................................2-65
Chapter 3 Remote Control ................................................................. 3-1
Remote Control Overview .......................................................................3-2
Control Via USB .....................................................................................3-3
Control Via LAN......................................................................................3-5
Control Via GPIB ....................................................................................3-8
Chapter 4 Application Examples ........................................................ 4-1
To Output RF Signal ...............................................................................4-2
To Output RF Sweep Signal .....................................................................4-3
To Output RF Modulated Signal ...............................................................4-5
Pulse Train Application............................................................................4-6
Chapter 5 Troubleshooting ................................................................ 5-1
Chapter 6 Specifications .................................................................... 6-1
Specifications ........................................................................................6-2
Frequency.......................................................................................6-2
Level ..............................................................................................6-4
Internal Modulation Generator (LF) ...................................................6-5
Modulation [1] ..................................................................................6-6
Inputs and Outputs........................................................................6-10
General Specifications ..........................................................................6-11
Chapter 7 Appendix ........................................................................... 7-1
Appendix A: DSG3000 Accessories and options .........................................7-1
Appendix B: Warranty.............................................................................7-2
I ndex........................................................................................................1

Chapter 1 Quick Start RIGOL
DSG3000 User’s Guide 1-1
Chapter 1 Quick Start
This chapter guides users to quickly get familiar with the appearance, dimensions,
front panel, rear panel, and the user interface of DSG3000 series RF signal generator.
The contents of this chapter are as follows:
General Inspection
Appearance and Dimensions
Front Panel Overview
Rear Panel Overview
To Use DSG3000 for the First Time
To Replace the Fuse
User Interface
To Use the Built-in Help System

RIGOL Chapter 1 Quick Start
1-2 DSG3000 User’s Guide
General I nspection
1. I nspect the shipping container for damage
Keep the damaged shipping container or cushioning material until the contents
of the shipment have been checked for completeness and the instrument has
passed both electrical and mechanical tests.
The consigner or carrier shall be liable for the damage to instrument resulting
from shipment. RIGOL is not responsible for free maintenance/rework or
replacement of the unit in such cases.
2. I nspect the instrument
In case of any damage, or defect, or failure, notify your RIGOL sales
representative immediately.
3. Check the accessories
Please check the accessories according to the packing lists. If the accessories
are incomplete or damaged, please contact your RIGOL sales representative
immediately.

Chapter 1 Quick Start RIGOL
DSG3000 User’s Guide 1-3
Appearance and Dimensions
Figure 1-1 Front View (unit: mm)
Figure 1-2 Top View (unit: mm)

RIGOL Chapter 1 Quick Start
1-4 DSG3000 User’s Guide
Figure 1-3 Lateral View (unit: mm)