MOLEAER LOTUS User manual

A supplemental oxygen gas tank is required to operate
the Lotus nanobubble generator. Oxygen gas tank is not
included. For safety, follow local electrical codes.
Notes
Unpacking
Installation Attach Oxygen Tank
Scan to Download the Owner’s Manual
and access warranty information for the
Lotus Nanobubble Generator.
www.moleaer.com
Ensure all accessories were provided
with your Lotus. Contact Moleaer
for replacement parts. Inspect outer
surfaces for shipping damage.
Open lid and remove packaging and
accessories from the inside.
Inspect components inside of
unit for any loose tubing or damaged
components and tighten any
loose ttings or tubing.
NANOBUBBLE GENERATOR
Quick Start Guide
1.1
1. 2
1
2 3
Install unit on a level surface.
Position unit within three feet of a standard
three-prong 120-volt outlet (15-amps).
Position unit as close to the water tank as
possible, while maintaining a minimum
distance to electrical outlet.
Ensure there is a minimum one-foot
clearance on all sides of unit to avoid risk
of damage.
Ensure the pump level is below the
minimum water level in the tank so the
pump is fed by gravity. Please see the
detailed operating manual for non-ooded
suction installations.
Unit Position
& Location:
2 .1
2.2
2.3
2.4
2.5
Rent or buy a K or T style
oxygen gas tank.
Connect the regulator Ato
the O2tank, set the dial to 0.
Connect the air tting Dto
the Lotus enclosure.
Connect the gas tube between
the regulator and the air tting.
Use the snap-grip clamps for
securing the tube.
Turn the regulator knob to the
lowest settings and check for
leaks using soapy water. Turn
the regulator dial back to 0.
3 .1
3.2
3.3
3.4
3.5
+1.424.558.3567
O2tank, water tank and pipes not included.
AGas Regulator, BPiping Connections,
CSpare O-rings DBarbed Fitting, ETube,
FSnap-Grip Clamps, GCIP Kit, HKeys
1.3
A
B
C
D
E
F
H
G

Using PVC glue (not included), attach hard or exible PVC piping to the two included
connectors, taking note of the orientation of the intake and discharge and the location of the
tank. Connection size is 1.5" and hard PVC piping should be 1.5" for inlet and discharge.
Note 1: The intake and discharge piping should be as short as possible. Do not exceed 20 feet for
either the intake or discharge pipes.
Note 2: The unit should not be placed more than six feet above the nominal water level.
Refer to owner’s manual piping placement and pump restrictions.
Included glue-able connections should be hand tightened only, do not use tools to tighten onto
the pump or discharge. Ensure all connections are tight before beginning startup steps.
Attach Piping
Startup
NANOBUBBLE GENERATOR |Quick Start Guide
Scan to Download
the Owner’s Manual
and access warranty
information for the Lotus
Nanobubble Generator.
www.moleaer.com
Copyright © 2022 Moleaer. All trademarks stated herein are the property of their
respective company. All rights reserved. This document is condential and contains
proprietary information of Moleaer Inc. Neither this document nor any of the
information contained herein may be reproduced, redistributed or disclosed under any
circumstances without the express written permission of Moleaer Inc. Rev. 07-05-22
Please contact Moleaer with any
questions or concerns: +1.424.558.3567
4
5
4 .1
4.2
Hand-tighten any
loose ttings.
Open the lid of Lotus
and open any isolation
valves between the unit and
tank on both the inlet and
discharge pipes
When the pump strainer
lls with water, tighten the
pump strainer basket lid by
turning the lid clockwise.
Run the unit for a minimum
of 60 minutes. Adjust the
oxygen regulator knob to
meet the desired levels of
dissolved oxygen.
Remove the pump
basket lid by turning it
counterclockwise. With
ooded suction, the basket
should ll by gravity.
Turn the oxygen regulator
knob to ¼ (1/4 lpm). Check
for any leaks inside the
enclosure at various
connection points.
Check that water is owing
through the pump by
verifying that the strainer
basket is lled with water.
Turn the Lotus on by
pushing the start button.
5.25 .1
5.65.5
5.3
5.7
5.4
5.8
60 min