Rilox 3103 User manual

IR Manual
Version 1.0 Lug.2020
IR receiver 3103
required

INDEX
1.1 Products .........................................................................................................................................4
1.2 Preparation ....................................................................................................................................5
1.3 Button layout .................................................................................................................................6
2.1 Auto calibration..............................................................................................................................7
3.1 Programming Rilox Go-Rail motor units ........................................................................................8
3.2 Overview Programming Menus .....................................................................................................9
3.3 Programming options ..................................................................................................................10
Menu 1...........................................................................................................................................10
1.1 Set end positions..................................................................................................................10
1.2 Set IR channels .....................................................................................................................10
1.3 Set RF channels ....................................................................................................................11
Menu 2...........................................................................................................................................12
2.1 Opening and Closing Speed .................................................................................................12
2.2 Intermediate positions.........................................................................................................12
2.3 Light Sensor..........................................................................................................................13
2.4 CPS: Curtain Protection System ...........................................................................................17
Menu 3...........................................................................................................................................19
3.1 Operation mode...................................................................................................................19
3.2 Inverted input ......................................................................................................................20
3.3 Timer ....................................................................................................................................20
3.4 –3.6 (Reserved) ...................................................................................................................21
3.7 Factory Settings....................................................................................................................21
4.1 Transmitter...................................................................................................................................22
4.2 LED Signals....................................................................................................................................24
4.3 Connessioni..................................................................................................................................25

4
1. Infrared control
1.1 Products
Rilox Go-Rail motor units offer a wide range of features for optimal use in many situations. Feature
settings can be changed and stored by means of the buttons on the motor unit itself or other
controllers, e.g. the IR transmitter.
During programming, there is a visual feedback from the multicolor LED in the motor unit.
Transmitter
Go-Rail electric curtain rail systems can be operated and programmed with the
Rilox IR transmitter (3104) and the IR receiver (3103 ).
The IR transmitter can transmit 15 different channels. On the IR transmitter,
IR channel ‘A1’ is pre-programmed as default.
To make changes in the IR channels, see p.11: “SET IR Channels” in Menu 1.
The transmitter uses 2 x AAA batteries (included).
Trasmitter
IR 3104
IR Receiver
The IR receiver is provided with 1 RJ45 plug and a IR-receiving eye. Cord lenght
is 100 cm.
The RJ45 plug is placed in the underside of the motor unit (see below for
detailed instructions).
The adhesive dot is used to place the receiving eye with its back against a
surface, such that IR signals from the transmitter can reach the eye. Each
receiver responds to up to 15 channels. This way, a curtain rail system can
respond to its individual IR signal and also to IR signals for a set ‘group’ or ‘all
systems’.
IR receiver
3103

5
1.2 Preparation
Trasmitter
Place the batteries in the trasmitter, 2 x AAA.
IR Riceiver
The connecting lead with RJ45 plug has to be inserted in the bottom side of the motor unit.
Place connector RJ45 here:
(underside motor unit
with bottom cover
removed).
The cable (100 cm) can be partly hidden, by using one of the side
channels in the motor unit housing with decorative strip. Replace
bottom cover to finish.
Multiple curtain rail systems:
Provide each system with an IR receiver, make sure to program systems one by one.

6
SET –used in setting the 24hr timer function
P –Programming button
RESET –used in setting the 24hr timer function
I –V:
Curtain control: Intermediate positions. pro-
gramming extra stops, up to five positions per
motor.
p.13: Setting intermediate positions
p.13: Using intermediate positions
Programming: no function
A –C: Channel group pre-selection
Curtain control: Press A, B, or C and then 1, 2,
3, 4 or 5 to select 1 out of 15 possible
channels (A1-A5, B1-B5, C1-C5).
The red LED indicates selection A, B or C.
Programming: No function
1 –5 OPEN / CLOSE:
Curtain control: Send an open or close signal on
selected channel A1 - A5, B1 - B5, C1 - C5.
Programming: Cycle through menu options
1.3 Button layout
The remote control 3104 can be used for operating and programming Go-Rail motor units. Below
an overview of the various buttons and their use.
Button timings:
Shortly press the button(s) (I)
= keep pressed less than 1 second
Press and hold the button(s) (I)
= keep pressed for more than 1 second
p.13
§ 3.3
p.8
§ 3.3

7
2. First Use
2.1 Auto calibration
The system will auto calibrate its end positions on first use, when the system is powered and
operated for the first time via IR channel ‘A1’.
After auto calibration, the system is ready for use and responds to Infrared channel ‘A1’ as default.
For motor types GM-x21-xxxx/x e GM-x10-xxxx/x (NOT for GM-1xx-xxxx/x).
To fine tune end
positions during
auto calibration,
these buttons can be
used.
1. Place the motor unit onto the curtain rail system
(see Go-Rail manual).
2. Place the curtains if possible and then adjust
internal endstop(s) if necessary, for improved
curtain pleating. (art. 3109, Allen key 2). These
stops are pre-secured and limit the running
distance of the pilot carrier. During the auto
calibration cycle below, electronically defined ‘soft
stops’ will be set with the 3109 stops as reference.
3. Connect an active power source (type depends on motor unit type).
4. Shortly press one of the buttons on the underside of motor unit or the controlling device.
5. The LED on the motor unit now flashes red.
6. The system will run until it is stopped by the internal end stop.
7. The system will move ~1cm in opposite direction and then waits for 5 seconds: within 5
seconds start fine tuning this end position if necessary, using the buttons.
8. After 5 seconds without signal, the calibration cycle continues. The system now runs in
opposite direction until it is stopped by the internal end stop.
9. The system will move ~5cms and then waits for 5 seconds: within 5 seconds start fine
tuning this end position if necessary, using the buttons.
10. After 5 seconds without signal, the system will move 20cm in Open direction, the cycle
stops and the red LED switches off. CPS mode is switched on automatically. The system is
now ready for use.
During auto calibration, the cycle can be aborted at all times by pressing one of the buttons.
3109

8
P button –enter a menu or to confirm an option.
OPEN / CLOSE buttons: cycle through menu/feature options
3. Programming
3.1 Programming Rilox Go-Rail motor units
Rilox Go-Rail motor units offer a wide range of features for optimal use in many situations. See §
3.2 on p. 9 for an overview of all available features.
Feature settings can be changed and stored using the buttons on the motor unit itself or the
Infrared transmitter.
Programming is done with aid of visual feedback from the multicolor LED in the motor unit.
Each programming feature is represented by 1 colour, for example the feature ‘setting end
positions’, shows a red LED.
Feedback also consists of blinking patterns to identify the selected feature setting.
To enter, navigate and make selections within Programming mode, these
buttons are used:
In programming mode all IR channels are active.
In the event of a power cut, the infrared channels will remain stored in the motor unit.

9
3.2 Overview Programming Menus
LED mode
LED colour
Menu 1
ON
Bianco
1.1
Endpositions
ON
Red
1.2
Set IR Channels
ON
Green
1.3*)
RF
ON
Yellow
(riservato)
LED mode
LED colour
Menu 2
Blinks slowly
White
2.1
Speed
ON
Red
2.2
DryC. Intermediate Positions
ON
Green
2.3
Light Sensor
2.3.1
Sun Sensor
ON
Yellow
2.3.2
Dawn/Dusk Sensor
ON
Blue
2.3.3
Sensor mode
ON
Purple
2.4
C.P.S.
2.4.1
Touch & Go
ON
Orange
2.4.2
Touch & Hold
ON
Light Blue
LED mode
LED colour
Menu 3
Blinks fast
White
3.1
Control mode
Red
3.2
CW / CCW inverted input
Green
3.3
Timer
Yellow
(riservato)
3.7
Factory Settings
Light Blue
*) If you have RF control, see RF manual for further control and programming options.

10
3.3 Programming options
Menu 1
1.1 Set end positions
Note: After 15s. without input, the motor unit quits programming mode. Please first read each step for this feature.
Infrared channel ‚A1‘ on the transmitter is active by default.
1. Place the curtains if possible and then adjust
internal endstop(s) if necessary, for improved
curtain pleating (art. 3109, allen key 2mm). These
stops are pre-secured and limit the running
distance of the pilot carrier. During the auto-
calibration cycle below, electronically defined ‘soft
stops’ will be set with the 3109 stops as reference.
2. Press and hold the P-button on the transmitter until the LED ON THE MOTOR UNIT turns
white (after ~4s.)..
3. Repeatedly press any OPEN or CLOSE button until the LED on the motor unit is red.
4. Shortly press the P-button to enter the feature menu, the LED on the motor unit now
flashes red.
5. The system will run until it is stopped by the internal end stop.
6. The system will move ~1cm in opposite direction and then waits for 5 seconds: within 5
seconds start fine tuning this end position if necessary, using the OPEN or CLOSE buttons.
7. After 5 seconds without signal, the calibration cycle continues. The system now runs in
opposite direction until it is stopped by the internal end stop.
8. The system will move ~5cms and then waits for 5 seconds: within 5 seconds start fine
tuning this end position if necessary, using the OPEN or CLOSE buttons.
9. After 5 seconds without signal, the system will move 20cm in Open direction.This
completes calibration and the red LED on the motor unit switches off. CPS mode is
switched on automatically. The system is now ready for use.
1.2 Set IR channels
Add and erase IR channels using the Infrared remote control.
Connect the infrared receiver to the underside of the motor unit. By default channel 1 is active.
Ensure the IR transmitter signals can reach the IR receiver.
Note: After 15s. without input, the motor unit quits programming mode.
Please first read each step for this feature.
motor LED colour red:
motor LED colour green:
3109