ritetemp 6030 User manual

MENU
PROG
HEAT
COOL
OFF
FAN
AUTO
ON
Operation 6030
ENGLISH

Statement of use: The 6030 can be used with millivolt,
24VAC, single and 2 stage conventional systems,
gas/oil/electric heat, 1 stage heat pumps, 2 stage heat
pumps, zoned hot water (2 or 3 wire), zoned forced air,
single and 2 stage cooling and hybrid systems.
Using a TOUCH SCREEN
Thermostat
Mode
PG 2
PG 1
Day
Time of day
Touch here
to change
from 12 to 24hr
clock display.
Time
Slot
Current Room
Temperature
Chirp indicator
Target
Temperature
MENU
PROG
HEAT
COOL
OFF
FAN
AUTO
ON
Menu
button
Program
button
Mode
Switch
Fan
Switch
Day
Time
of day
Time
Slot Current
Room Temperature
Touch
Screen
Thermostat
Mode
Target
Temperature
Please take a moment to try out
your touch screen itself.
To select a function on the
touch screen, place your finger
on the main temp display and
give a short firm push. Try a
"tap" of the finger or stylus. Your
input must last long enough for
the system to determine it is not
an accidental 'bump'.
Using the stylus is more comfortable for some
users. Again allow the system enough time to
recognize your inputs.
When you are comfortable with touch inputs,
proceed.
Basic Screens
The MODE SWITCH of the 6030 must be in the HEAT or the COOL position to
access all control functions. The 6030 Thermostat has 3 basic screens.
The HOME screen is displayed when unit is operating your system.
Touching the will always return you to this screen.
HOME screen
Operation 6030

AM
PG 3
PG 4
Set Day
Touch this area to set
the day of the week.
Set Time
Touch this area to set
the time of day.
Left arrow goes back,
right arrow goes forward.
Calibration indicator
This shows if you
have altered the
calibration of your unit
Calibration control
Use this to calibrate your LCD
display match to another
thermometer.
Set
o
C -
o
F
Touch this to
set temperature
display.
Lock Program
Touch for 5 sec
to lock or unlock
Filter Timer set
Chirp set
Touch this to turn
the audible chirp
on or off.
Temperature Swing set
Return
HOME
Set Program Day
Touch this area to set
the day of the week you
want to program Target
Temps for.
Set Time Slot
Touch this area to set
the Time Slot you
want to program.
Set Program Time
Touch this area to set the
time of day you want each
time period to start.
Left arrow goes back,
right arrow goes forward.
Copy
Touch this area to copy
current program to the
next day Temp Up / Temp Down
arrows. Touch these to raise
and lower each Target Temp.
EPA
Touch and hold for
5 sec to return to
EPA Energy-Star prog
Review
touch this area to auto cycle
through your program
Return HOME
When programming
is complete touch this
to run your program.
Displayed when the MENU button is pressed.
Displayed when the PROGRAM button is pressed.
MENU screen
PROGRAM screen
AM
EPA

Configure
Auto-run
Press MENU to configure the thermostat (from HOME screen).
Set day of the week -
Touch the Day of the week area to cycle through the
days of the week to select the current day.
Set time of day -
Touch the Time of Day arrows to move the time
selection forward or backward until it displays the
current time. Touch and hold for faster setting.
Set
o
C -
o
F display
Touch the
o
F and it will toggle to
o
C.
Set audible chirp -
Touch the the musical note icon to select the chirp
or no chirp.
EPA - Touch and hold for 5 sec to return to EPA Energy-Star program
Return HOME by touching the home icon.
This Thermostat comes preprogrammed with an Energy-
Star
TM
approved program. This program is recommended by
the EPA for energy efficiency.
We strongly recommend that youAuto-Run this program for one week,
and see if it works for you. If it does not fit your needs you can always input
a custom program.
• To Auto-Run the Energy-StarTM program, select HEAT or COOL with the
mode switch. The unit is now running the Energy-StarTM program.
• The clock is displayed on the left. The ambient temperature is displayed in
the the center of the LCD touch screen. The TIME SLOT icon indicates the
TIME SLOT active in the Energy-StarTm program.
• The programmed temperature is shown on the lower right. For program
details refer to the Energy-Star
TM
program chart below.
PG 5
PG 6
All Days 70
o
F  62
o
F   70
o
F  
MORN
6:00am
HEAT DAY
8:00am EVEN
6:00pm NITE 10:00pm All Days 78
o
F    85
o
F 
MORN
6:00am
COOL DAY
8:00am EVEN
6:00pm NITE 10:00pm
ForwardBackward
The Mode Switch must be in
HEAT or COOL mode to configure.
EPA
EPA

Program
Program cont.
NOTE: 60 Second Rule-During programming, if a button is not pushed in
60 seconds, the unit will return to the home screen. Everything you have
changed while programming will automatically be saved.
PG 7
PG 8
Select HEAT with the HEAT/Cool MODE switch.
Press PROGRAM to go to the programming screen.
Select the day you want to program-
Touch the Day of the week area to cycle through
the days of the week to select the desired day.
Select the time slot you want to program -
Touch the Time slot area to cycle through the 4
time slots, until it displays the desired time slot.
Select the time of day -
Touch the Time of Day arrows to move the time
selection forward or backward until it displays the
desired time. Touch and hold for faster time set. ForwardBackward
Select the desired temperature -
Touch the UP temp / Down temp arrows.
Repeat the above procedures for each day of the week and
each time slot of the day as desired.
To REVIEW your program touch REVIEW. Each time slot for each day
or set of identical days, will be displayed every 3 seconds.
Return HOME by touching the home icon.
To COPY the program from the current day to another day -
Touch COPY on the program screen. The current day will remain solid,
the destination day will flash.
Touch the day area to advance the day and select a copy destination.
Touch COPY again to copy all settings to the destination day.
To program for cooling -
Select COOL with the Heat/Cool MODE switch and repeat the
above procedure.

Manual cont.
Manual
Temporary OVERRIDE -
• At the Manual override screen, Touch the Temp Up / Temp Down
arrows to select your desired temporary Target Temperature.
• Touch HOME to return to operation.
The OVERRIDE icon will go on indicating you have modified the
Target Temp for the current Time Slot only (see PG7-Time Slot).
The 6030 has 3 manual override commands. These are accessed by
touching the Current Temp Display at the HOME screen (center of screen).
PG 9
PG 10
Target Temperature
HOLD
Touch this area to set
a comfortable target
temp for the system
to hold until you return
and remove HOLD.
Return HOME
Temp Up / Temp Down arrows
Touch these to raise and lower
the manual override Target Temp.
Manual Override indicator
Shows TEMPORARY when
you have modified the Target.
MANUAL override screen
HOLD -
• At the Manual override screen, Touch HOLD to initiate a hold
temperature.
• Touch the Temp Up / Temp Down arrows to select your hold
temperature.
• Touch HOME to return to operation.
The HOLD ON icon will flash indicating you have changed the
Target Temp.
The system will HOLD this temperature until you return to this screen
and de-select HOLD, by touching the HOLD icon again.
The Mode Switch must be in
HEAT or COOL mode to override.
TEMPORARY

Special Features
Spec. Featr. cont.
Swing
Swing setting determines the temperature
difference in degrees from ON to OFF that
the thermostat will command the HVAC system to run.
With the MODE switch in HEAT or COOL, press the MENU button.
Touch the SWING icon and the current setting of temp swing is shown on
the display (default at .5
o
).
To change the swing factor, touch the left or right arrows.
The furnace will cycle more at the lower numbers as it tries to maintain your temp.
Filter
The 6030 has a feature that keeps track of actual furnace run
time and reminds you to periodically replace your system's air filter.
Press MENU (from HOME screen) and touch FILTER icon.
This will display your accumulated filter run time in weeks.
To zero the filter timer for a new filter, touch the accumulated time display.
To input a new filter life time, touch the FILTER icon for 3 seconds.
Input the lifetime in weeks for your new filter.
To leave the filter display, touch HOME.
Lock
Allows you to to prevent any changes in custom settings.
To Lock Level1, touch the LOCK icon on the MENU screen for 2 sec.
Level1 allows temporary target adjustments but no program changes
To Lock Level2, touch LOCK icon for 2 sec. Level2 allows no changes.
To unlock, Touch the locked icon for 2 sec.
Low Battery When the batteries are low, the battery icon will flash.
The two AAA Batteries in the unit need to be replaced. In
some installations your heater system will stop functioning when the
thermostat loses power. Replace batteries as soon as you see this
warning. The thermostat programs will remain for 60 seconds while
the batteries are changed.
Do not take longer than 60 sec to change the batteries in your unit or
you will lose all custom settings and all programming. Only the Energy-
StarTM program will remain. Once the batteries are replaced, the system
will return to normal in 2 seconds.
12/24 hour The thermostat can display time in 12 or 24 hour formats.
At the HOME screen touch the time to toggle from 12 to 24 hr display.
PG 11
PG 12
WKS

AM
MENU
PROG
HEAT
COOL
OFF
FAN
AUTO
ON
P14
P13
If you have configured your 6030 for
heat pump control the MENU screen
will display an additional icon - the
HEAT PUMP ON/OFF icon.
When using a heat pump with
Auxiliary heat, if the heat pump
cannot keep up and/or is defective,
touch the MENU button, then touch
PUMP ON; the PUMP OFF icon will
come on. The aux heat will then be
your only source of heat.
When the heat pump is again operational, be sure to turn
the heat pump back on by touching MENU and then PUMP
OFF (off icon goes out) as the aux heat is more expensive
than pump heat.
Heat Pump Features
This thermostat can be used with all millivolt and 24VAC heating and cooling systems.
It cannot be used with line voltage systems. This thermostat is digital and your desired
heat or cool temperatures can be easily be set on the large touch screen with the
UP/DOWN arrows. A minimum 4 minute off time protects heating and cooling systems
from damage. 
This thermostat uses a new
technique called sequential
staging for more comfort with
faster reaction to requested
temperature changes.
6035 Features
PUMP OFF
PUMP OFF
MENU screen
HEAT PUMP
ON/OFF ICON

Made in China 1611-025
Calibration
AM
Customer Support: 877-505-2353 or
Visit our website www.ritetemp-thermostats.com
NOTE: Your thermostat comes from the factory calibrated to + or - 1oF actual temperature. It
is an accurate instrument. If you want your thermostat to display the same temperature as
another thermometer in your home, you can adjust it. Maximum calibration is +/-6o.

To change the calibration:
With the switch MODE in HEAT or COOL.
Press the MENU button.
Press the Temp Up/Temp Down arrows to adjust the temperature reading.
CALIBRATE DISPLAY ON will appear.
Press HOME to save the new setting.