ritetemp 8022C Instruction Manual

Operation 8022C
Customer Support: 888-515-2585 or
Visit our webiste www.ritetemp-thermostats.com
Made In China 401-006
HEAT COOL
AUTO ON
OFF FAN
PM
F
SET TEMP
HEAT
HEAT COOL
AUTO ON
OFF FAN
PM
F
SET TEMP
HEAT

Statement of use: The GPMG8022c can be used with
most 24 volt gas, oil or electric heating and air conditioning
systems, single-stage heat pumps or gas millivolt heating
systems.It cannot be used with 120 volt heating
systems or multistage heat pumps.
SET CLOCK
BATTERY
SDP
COPY
HOME
TEMP HOLD
PROGRAM
TIME SLOT
TIME SET
RESET
NEXT PTIME
TIME
DAY
TEMP
UP
DOWN
MODE FAN
Operation 8022C
1 Set Clock
HEAT COOL
AUTO ON
OFF FAN
TEMP UP
button
TEMP DOWN
button
Set Temp
Display
Time/ Current Temp
Display AA Battery
Compartment Control Panel
- Cover Closed -
Reset button
Mode
Switch
Fan
Switch
Heat/Cool
Mode Switch
Fan
Switch
Set day of the week-
Press SET CLOCKonceto set theday of the week. The
day of the week display flashes. (Initially SU for Sunday)
Press <TIME or TIME>
to select the day.
Press HOME to store your
settings.
Set time of day-
Press SET CLOCKtwiceto set
thetime. The time display will
flash.
Press <TIME or TIME> to set
the time. Press and hold to set
the time in the fast mode.
Press HOME to store your
settings.
TIMETIME
TIMETIME
PG 2
PG 1
PM
FILTER
REVIEW
PM
SET CLOCK SDP
FILTER
HOME
PROGRAM
TIME SLOT
TIME SET
RESET
NEXTP
TIME
TIME
DAY
BATTERY
TEMP
UP
DOWN
MODE FAN
REVIEW
COPY
TEMP HOLD
F
P2
SET TEMP
SET TEMP
SET TEMP

2 Auto-run
This Thermostat comes preprogrammed with an Energy-StarTM
approved program. This program is recommended by the EPA for
energy efficiency.
We strongly recommend that you Auto-Run this
program for one week, and see if it works for you.
If it does not fit your needs you can always input a
custom program.
To Auto-Run the Energy-StarTM program, select HEAT or COOL with the mode
switch. The unit is now running the Energy-StarTM program.
The clock and the ambient temperature are displayed on the right.
They alternate every 2 seconds. One of the TIME SLOT icons P1/P2/P3/P4
comes on, this indicates the TIME SLOT active in the Energy-StarTm program.
The programmed temperature is shown on the left. For program details refer to
the Energy-StarTM program chart below.
3 Program
Select HEAT with the HEAT/Cool MODE switch.
Select the day you want to program: Press the
PROGRAM to enter programming mode. The
PROGRAM FOR icon will come on. The day icon will
show SU (Sunday). Pressday again to advance
the day selection.
Select the TIME SLOT you want to program:To change the TIME SLOT
( P1, P2, P3, P4 ) press the NEXT button. The display will cycle through the
time periods in sequence. Select P1.
Select the desired temperature for that TIME SLOT :To change the
temperature for that TIME SLOT press the TEMP UP / TEMP DOWNbuttons.
Select the time of day you want that TIME SLOT to represent:
To set the time when P1 will begin , press the <TIME or TIME> buttons to
move the set point forward or backward in time.
NOTE:60 Second Rule-Duringprogramming, if a button is not
pushed within 60 seconds, the unit will go out of the set mode.
Everything you have input in this programming will automatically be saved.
NEXTP
DAY
PG 3
PG 4
All Days  70
o
F   62
o
F   70
o
F    
P1
6:00am
HEAT P2
8:00am P3
6:00pm P4 10:00pm All Days  78
o
F   85
o
F   78
o
F    
P1
6:00am
COOL P2
8:00am P3
6:00pm P4 10:00pm
TIME TIME
SET TEMP
SET TEMP

To program an alternate or "Special Day" program, that you can access at
any time, press PRO until PROGRAM FOR for SDP DAY is displayed.
Repeat the procedure above to program temp settings for theSpecial Day.
To program for cooling,select COOL with the Heat/Cool MODE switch and
repeat the above procedure.
To REVIEW the program you have entered:
Press PROGRAM once to enter programming mode.
Then press FILTER/REVIEW once.
The display will cycle through the prgrammed times and temps, showing
each program for 12 seconds. Starting from Sunday; P1 and ending on
Saturday; P4. The programmed temperature is shown on the left of the LCD,
the programmed time, day and time slot are shown on the right and the right
top of the LCD respectfully.
Press HOME to leave program REVIEW mode and run the program.
3 Program cont.
3 Program cont.
Select the next TIME SLOT and program temp and time:
Press NEXT>, the display will show P2, for Period 2. Repeat setting temp
and time. Select the remaining TIME SLOT's, P3 and P4. Program their temp
and time info.
Repeat the above procedures for each day of the week. Push DAY> button
to cycle through the days.
To COPY the program of the current day to another day, pressCOPY
program once. COPY will display on the LCD. The day icon for the source
day will go solid and the day icon for the destination day will flash. Use day
button to select the destination day. Press COPY again to confirm the copy.
If you decide you don't want to copy, press HOME to exit.
NEXTP
DAY
DAY
PG 5
DAY
PG 6
When finished with your custom program, either wait 60 sec or press HOME
to save and run your program.

DOWN-Arrow
button
UP-Arrow
button
4 Spec. Featr. cont.
Swing
Swing setting determines the temperature difference from
ON to OFF that the thermostat will command the heating/cooling system to run.
With the MODE switch in HEAT or COOL, press the button.
The SET TEMP SWING icon is displayed. The current setting of temp swing is
shown on the display (default at 3 ).
To change the swing, push TEMP UP or TEMP DOWN buttons. The furnace will
cycle more at the lower numbers as it tries to keep your set point constant.
To complete the swing setting, push the HOME button.
Manual
With the MODE switch in HEAT or COOL, push the UP or DOWN
arrow buttons to temporarily change the control temperature by 1
degree per step. Press and hold for faster setting.
The OVERRIDE icon comes on which shows the displayed
temperature may be different from the programmed setting.
The OVERRIDE is canceled at the start of the next time period,
or when the MODE switch is moved, or if TEMP HOLD is pressed twice.
TIME
PG 8
SDP
4 Special Features
The "Special Day Program" can be used when you are unexpectedly home
and need to activate this heat / cooling program just for the day.
With the MODE switch in HEAT or COOL press the SPECIAL DAY button to
activate.
When the SPECIAL DAY Program is active, all other day settings are all
ignored even if the day is matched.
The SPECIAL DAY program will terminate when the mode switchis moved
or if the SPECIAL DAY button is pushed again.
PG 7
SET TEMP

4 Spec. Ftr. cont.
Lock
Allows you to lock the Program (to prevent any changes in custom settings)
To enable or disable the program lock, press the following buttons one at a time,
in this sequence.
<tim then FILTER , then SET CLOCK , and last HOME .
The LOCK icon (a key) appears when the system is locked. Repeat to unklock
Low Battery
When the batteries are low, the battery icon will come on and flash.
The two AA Batteries in the unit need to be replaced. In some installations your
heater system will stop functioning when the thermosat losespower. Replace
batteries as soon as you see this warning.The thermostat programs will
remain for 30 seconds while the batteries are removed and replaced.
Do not take longer than 30 sec to change the batteries in your unit
or you will lose all custom settings and all programming. Only the
Energy-Star
TM program will remain. Once the batteries are replaced, the
system will return to normal in 2 seconds. PG 10
TIME
4 Spec. Featr. cont.
TEMP HOLD
To change and hold the temperature until you return.
Open the door and push the TEMP HOLD button. The HOLD icon comes on.
Push the UP or DOWN arrow buttons to set the hold temperature.
HOLD is canceled if the MODE switch is moved, or press TEMP HOLD again.
Filter
The life of a heater filter varies depending on many factors, furnace run
time, and this will vary from the filter life noted on the filter media.
The 8022C has a feature that keeps track of actual furnace run time and
reminds you to periodically replace your system's air filter.
Press the FILTER button once to review the current filter record.
The FILTER and HR icons come on with accumulated filter hours being displayed.
Press to clear the record. Press again to recover the previous record.
To see the filter limit setting, press and hold the FILTER button for two seconds.
To change the filter limit hours setting, press F. oror B. Press and
hold for faster setting. The filter limit can be set within000-500 hours.
To leave the filter display, press HOME or wait 60 seconds. PG 9
TIME
TIME
TIME

NOTE: Your thermostat comes from the factory calibrated to+ or - 1oF actual
temperature. It is an accurate instrument. If you want your thermostat to display
the same temperature as another thermometer in your home, you can adjust its
calibration.
To change the calibration:
Mode switch of the unit must be in the HEAT or COOL position.
Press the <Time button.
Press the Temp Up/Temp Down arrows to adjust the temperaturereading.
Press HOME to save the new setting.
TIME
Calibration
PG 12
C or F display
Centigrade / Fahrenheit selection. The C/F jumper is on theback of the
thermostat control unit. Separate the control unit from thewall mounted
terminals. When changed, the thermostat must be reset to activate the change.
When resetting, all custom settings and programming will beerased and only
the Energy-Star
TM program will remain.
12/24 hour
The thermostat can display
time in 12 or 24 hour
formats. The 12/24 jumper
is on the back of the
thermostat
(see illustration).
When changed, the
thermostat must be reset to
activate the change.
PG 11
o
C -
o
F jumper 12/24hr
jumper
Gas - Electric jumper
Circuit
Board
Rear View of control unit
ELECT GAS
24
12
o
C
o
F