RiverGrille TF2014501-RG-00 Quick setup guide

TF2014501-RG-00 Eng Page 1 20160930 V.1
18QT Double Fish Fryer
Assembly, Use and Care For Outdoor Use Only
Model: TF2014501-RG-00
Tools required:
Phillips screwdriver / Adjustable wrench
To installer or person assembling this appliance: Leave this manual with this
appliance for future reference.
This instruction manual contains important information necessary for the proper
assembly and safe use of the appliance.
Read and follow all warnings and instructions before assembling and using the
appliance.
Follow all warnings and instructions when using the appliance.
Keep this manual for future reference.
This appliance is not for frying turkey.

TF2014501-RG-00 Eng Page 2 20160930 V.1
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from the appliance and
immediately call your fire department.
Failure to follow these instructions could result in fire or explosion
which could cause property damage, personal injury or death.
DANGER
1. Never operate this appliance unattended.
2. Never operate this appliance within 10 feet or 3m of any other
gas cylinder.
3. Never operate this appliance within 25 feet 7.5 m of any
flammable liquid.
4. Do not fill cooking vessel beyond maximum fill line.
5. Never allow oil/grease to get hotter than 400°F or 200°C. If the
temperature exceeds 400°F (200°C) or if oil begins to smoke,
immediately turn the burner or gas supply OFF.
6. Heated liquids remain at scalding temperatures long after the
cooking process. Never touch cooking appliance until liquids
have cooled to 115°F or 45 °C or less.
7. If a fire should occur, keep away from the appliance and
immediately call your fire department. Do not attempt to
extinguish an oil or grease fire with water.
Failure to follow these instructions could result in fire, explosion or
burn hazard which could cause property damage, personal injury
or death.

TF2014501-RG-00 Eng Page 3 20160930 V.1
WARNING
Combustion by-products when using this product contain chemicals known to the State
of California to cause cancer, birth defects, or other reproductive harm.
WARNING
This Appliance is not intended for commercial use.
Safety Symbols
The symbols and boxes shown below explain what each heading means. Read and follow
all of the messages found throughout the manual.
DANGER
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Warning: Indicates a potentially hazardous situation which, if not avoided, will result in
death or serious injury.
CAUTION
CAUTION: Indicates a potentially hazardous situation or unsafe practice which, if not
avoided, may result in minor or moderate injury.

TF2014501-RG-00 Eng Page 4 20160930 V.1
WARNING
1. Never leave the appliance unattended. Keep children and pets away from the
appliance at all times.
2. The use of alcohol, prescription or non-prescription drugs may impair the
consumer’s ability to properly assemble or safely operate the appliance.
3. This appliance is for OUTDOOR USE ONLY.DO NOT use in building, garage or
any other enclosed area. This appliance is not intended to be installed in or on
recreational vehicle and/or boats. This appliance is not intended for and should
never be used as a heater.
4. Fryer shall not be used on or in any apartment or condominium balcony or deck.
5. When cooking, the fryer / boiler must be on a level, stable noncombustible surface
in an area clear of combustible material. As asphalt surface (blacktop) may not be
acceptable for this purpose.
6. When cooking with oil or grease, the thermometer provided MUST be used.
Follow instructions in this manual for proper installation and use of the
thermometer. If the thermometer supplied with this fryer has been lost or
damaged. A replacement thermometer must be one specified by the appliance
manufacturer.
7. If the temperature exceeds 400°F (200°C) or if oil begins to smoke, immediately
turn the burner or gas supply OFF and wait for the temperature to decrease to less
than 350°F (175°C) before relighting burner according to the manufacturer’s
instructions. If there is a lid (cover), do not remove the lid.
8. When cooking with oil or grease, have a type BC or ABC fire extinguisher readily
available. In the event of an oil or grease fire do not attempt to extinguish with
water. Immediately call the fire department. A Type BC or ABC fire extinguisher
may, in some circumstances contain the fire.
9. Never overfill the cooking vessel with oil, grease or water. Follow
instructions in this manual for establishing proper oil, grease or water
levels. Never overfill the cooking vessel with oil, grease or water than
specified by vessel manufacturer instruction. If the vessel doesn’t indicate
the maximum fill line, please refer to following instructions for determining
the maximum fill level.
Determining the maximum fill level when using a vessel without a
maximum line:
(1) Place the food product in the basket.
(2) Place the food product and holder into the empty vessel.
(3) Fill the vessel with water just until the food product is completely
submerged. There must be a minimum of 3 inch (8 cm) between the water
level and top of the vessel.
(4) Remove the food product from the vessel and either mark the water
level on the side of the vessel or measure the amount of water in the
vessel.
(5) Remove the water and completely dry the vessel and the food product.

TF2014501-RG-00 Eng Page 5 20160930 V.1
(6) This is the amount of cooking oil the vessel is to be filled with to cook
the food product.
10. Introduction of water or ice from any source into the oil/grease may cause
overflow and severe burns from hot oil and water splatter. When frying
with oil/grease, all food products MUST be completely thawed and towel
dried before being immersed in the fryer.
11. Do not place empty cooking vessel on the appliance while in operation.
Use caution when placing anything in cooking vessel while the appliance
is in operation. Placing an empty cooking vessel on the appliance while in
operation will result in melting the cooking vessel. Use caution when
placing anything in cooking vessel while the appliance is in operation.
12. In the event of rain, snow, hail, sleet or other forms of precipitation while
cooking with oil or grease, cover the cooking vessel immediately and turn
off appliance burners and gas supply. Do not attempt to move the
appliance or cooking vessel.
13. Do not move the appliance when in use. Allow the cooking vessel to cool
to 115°F (45°C) before moving or storing.
14. Do not leave the appliance unattended, keep children and pets away from
the appliance at all times.
WARNING
Installation Safety Precautions.
Use appliance only with LP (propane) gas and the regulator/ valve assembly
supplied.
Installation must conform with local codes
or, in the absence of local codes, with the
National Fuel Gas Code, ANSI
Z223.1/NFPA 54, Storage and Handling of
Liquefied Petroleum Gases, ANSI/NFPA
58; or Natural Gas and Propane
Installation Code, CSA B1 49.1
This appliance shall be used only outdoors,
and shall not be used in a building, garage
or any other enclosed area.
Use appliance at least 10 ft. from any wall
or surface. Maintain 10 ft clearance to
objects that can catch fire or source of
ignition such as pilot lights on water
heaters, live electrical appliances, etc.
Never use under balconies made of wood or ANY overhead construction.
Apartment Dwellers: Check with management to learn the requirements and fire
codes for using an LP Gas appliance at an apartment. IF allowed use outside at
an apartment. If allowed, use outside on the ground floor with a ten (10) foot
clearance form walls or rails.
Before opening LP tank valve, check the coupling nut for tightness. When

TF2014501-RG-00 Eng Page 6 20160930 V.1
appliance is not in use, turn off control knob and LP tank valve.
Never move appliance while in operation or still hot.
If you notice grease or other hot material dripping from appliance onto valve, hose
or regulator, turn off gas supply at once. Determine the cause, correct, clean and
inspect valve, hose and regulator before continuing. Perform a leak test.
The regulator may make a humming or whistling noise during operation. This will
not affect safety or use of appliance.
Clean and inspect the hose before each use of the appliance. If there is evidence
of abrasion, wear, cuts or leaks, the hose must be replaced prior to the appliance
being put into operation.
WARNING
Never use a cooking vessel larger than 18 qts. Diameter greater than 13 x 16
inches and taller than 5 inches. A BIGGER VESSEL MAY RESULT IN
TIPPING.
Never fill pot above upper fill line. Oil can splatter causing staining or discoloration
to ground surface.
Never place empty cooking vessel on the appliance while in operation. Use
caution when placing anything in the cooking vessel while the appliance is in
operation.
Never move the appliance when in use. Allow the cooking vessel to cool before
moving or storing.
Never leave the appliance unattended. Keep children and pet away from the
appliance at all times.
This appliance is not intended for and should never be used as a heater.
Never operate appliance with LP tanks out of correct position specified in
assembly instructions.
Always close LP tank valve and remove coupling nut before moving LP tank from
specified operating position.
Appliance shall not be used for commercial cooking.
This appliance will be hot during and after use. Use insulated oven mitts or gloves
for protection from hot surfaces or splatter from cooking liquids.
Avoid bumping of or impact with the appliance to prevent spillage or splashing of
hot cooking liquid.
Keep the fuel supply hose away from any heated surface

TF2014501-RG-00 Eng Page 7 20160930 V.1
Never drop food or accessories into hot cooking liquid. Lower food and
accessories slowly into the cooking liquid in order to prevent splashing or
overflow. When removing food from the appliance care should be taken to avoid
burns from hot cooking liquids.
DANGER
The safety relief valve on the LP tank could activate releasing gas and cause an
intense fire with risk of death or serious injury. Therefore, follow instructions
bulleted below exactly.
(a) Do not store a spare LP-gas cylinder under or near this appliance.
(b) Never fill the cylinder beyond 80 percent full; and
(c) If the instructions in (a) and (b) are not followed exactly, a fire causing death
or serious injury any occur.
If you see, smell, or hear escaping gas, immediately get away from the LP
tank/appliance and call your fire department.
All spare LP tanks must have safety caps installed on the LP tank outlet.
LP Tank Removal, Transport and Storage
Turn OFF all control knobs and LP tank valve. Turn coupling nut counterclockwise by
hand only –do not use tools to disconnect. Install safety cap as directed may result in
serious personal injury and/or property damage.
Turn off gas at supply cylinder when not in use.
A disconnected LP tank in storage or being transported
must have a safety cap installed (as shown). Do not
store an LP tank in enclosed spaces such as a carport,
garage, porch, covered patio or other building. Never
leave an LP tank inside a vehicle which may become
overheated by the sun.
Do not store LP tanks in an area where children play.
LP Tank
The LP tank used with your appliance must meet the following requirements:
Purchase LP tanks only with these required measurements: 12”(30.5cm) (diameter)
x 18”(45.7cm)(tall) with 20lb. (9kg). Capacity maximum.
The LP-gas supply cylinder to be used must be constructed and marked in
accordance with the specifications for LP-gas cylinders of the US Department of
Transportation (DOT) or the National Standard of Canada, CAN/CSA-B339, Cylinders,
Spheres and Tubes for the Transportation of Dangerous Goods.

TF2014501-RG-00 Eng Page 8 20160930 V.1
LP tank valve must have:
Type 1 outlet compatible with regulator or appliance.
Safety relief valve.
UL listed Overfill Protection Device (OPD). This OPD safety
feature is identified by a unique triangular hand wheel. Use only
tanks equipped with this type of valve.
LP tank must be arranged for vapor withdrawal and include collar to
protect LP tank valve.
LP (Liquefied Petroleum Gas)
LP gas is non toxic, odorless and colorless when produced. For your safety, LP gas
has been an odor (similar to rotten cabbage) so that it can be smelled.
LP gas is highly flammable and may ignite unexpectedly when mixed with air.
LP Tank Filling
Use only licensed and experienced dealers.
LP dealer must purge tanks before filling.
Dealer should NEVER fill LP tank more than 80% of LP tank volume. Volume of
propane in tanks will vary by temperature.
A frosty regulator indicates gas overfill. Immediately close LP tank valve and call LP
gas dealer for assistance.
Do not release liquid propane (LP) gas into the atmosphere. This is a hazardous
practice.
To remove gas from LP tank, contact an LP dealer or call a local fire department for
assistance. Check the telephone directory under”GAS Companies”for nearest
certified PL dealers.
LP Tank Exchange
Many retailers that sell appliances offer you the option of replacing your empty LP
tanks through an exchange service, Use only those reputable exchange companies
that inspect, precision fill, test and certify their cylinders. Exchange your tank only for
an OPD safety feature-equipped tanks as described in the “LP Tank”section of this
manual.
Always keep new and exchanged LP tanks in upright position during use, transit or
storage.
Leak test new and exchanged LP tanks BEFORE connecting to appliance.
LP Tank Leak Test
For your safety
Leak test must be repeated each time LP tank is exchanged or
refilled.
Do not smoke during leak test.
Do not use an open flame to check for gas leaks.
Appliance must be leak checked outdoors in well-ventilated area,
away from open flames or sparks.

TF2014501-RG-00 Eng Page 9 20160930 V.1
Use a clean paint brush and 50/50 soap and water solution.
Use mild soap and water. Do not use household cleaning agents. Damage to gas train
components can result.
Brush soapy solution onto all weld seams and entire valve area.
WARNING
If “growing”bubbles appear, do not use or move the LP tank. Contact an LP gas supplier
or your file department.
Connecting Regulator to the LP Tank
1. Place LP tank on a secure, level, and stable surface.
2. Turn control knob to the OFF position.
3. Turn LP tank OFF by turning hand wheel clockwise to a full
stop.
4. Remove the protective cap from the LP tank valve.Always
use cap and strap supplied with valve.
5. Hold regulator, insert nipple (B) into LP tank valve. Hand tighten coupling nut, holding
regulator in a straight line (c) with LP tank valve sp as not to cross thread the
connection.
6. Turn the coupling nut clockwise to tighten
to a full solid stop. The regulator will seal
on the back-check feature in the LP tank
valve, resulting in some resistance. An
additional one-half to three quarters turn
is required to complete connection.
Tighten by hand only –do not use tools.
NOTE: If you cannot complete connection,
disconnect regulator and repeat step 5 and 6.
If you are still unable to complete the
connection, do not use this regulator!
Do not use a POL transport plug (A)
(plastic part with external threads)! It
will defeat the safety feature of the
valve.

TF2014501-RG-00 Eng Page 10 20160930 V.1
WARNING
Do not insert any tool or foreign object into the valve outlet or safety relief valve.
You may damage the valve and cause a leak. Leaking propane may result in
explosion, fire, severe personal injury, or death.
Never attempt to attach this appliance to the self-contained LP gas system of a
camper or trailer or motor home.
The pressure regulator and hose assembly supplied with the appliance must be
used. Replacement pressure regulator and hose assemblies must be those
specified by the appliance manufacturer.
WARNING
Do not use appliance until leak checked.
If leak is detected at any time, STOP.
If you cannot stop a gas leak, immediately close LP tank valve, leave area of
appliance, and call LP gas supplier or your fire department!
Leak Testing Valves, Hoses and Regulator
1. Turn all control knob(s) to OFF.
2. Be sure regulator is tightly connected to LP tanks.
3. Completely open LP tank valve by turning hand
wheel counterclockwise. If you hear a rushing
sound, turn gas off immediately. There is a major
leak at the connection. Correct before proceeding.
4. Brush soapy solution onto indicated connections
shown at right in A and B. (Reference connection of
hose to burner on page 15.)
5. If ‘growing”bubbles appear, there is a leak. Close
LP tank valve immediately and retighten
connections. If leaks cannot be stopped, do no try to
repair. Call for replacement parts. Order new parts
by giving the serial number, number and name of
items needed to the Customer Service Center at
1-888-837-1380 Use only replacement parts
specified by manufacturer.
6. Always close LP tank valve after performing tank
test by turning hand wheel clockwise.

TF2014501-RG-00 Eng Page 11 20160930 V.1
Lighting Instructions
Do not lean over LP cooker while lighting.
1. Turn regulator control valve to OFF position.
2. Fully open LP tank valve.
3. Light match and place it over burner. Slowly turn ON the
regulator control valve DO NOT stand with head or arms
over cooker.
4. If ignition does not occur in 5 seconds, turn the burner
control(s) off, wait 5 minutes, and repeat the lighting
procedure.
Curing of paints and parts will product an odor only on first
use.
CAUTION
If burner does not light OR if burner flame is accidentally extinguished, turn knob to OFF,
wait 5 minutes, try again. If the burner does not ignite with valve open OR if burner flame
is accidentally after lighting, gas will continue to flow out of the burner and could
accidentally ignite with risk of injury.
Burner Flame Check
Light burner, rotate
knob from HIGH to
LOW. You should see a
smaller flame in LOW
position than seen on
HIGH. Always check
flame prior to each use.
The air damper (D)
mounted on the back
of your burner helps to control the amount of primary air that mixes with the LP gas. A
blue flame with little or no yellow flame provides the best heat. Adjust the air damper
by turning it clockwise or counterclockwise until the desired flame is achieved.
Turning LP Cooker Off
Turn all knobs to OFF position, Turn LP tank OFF by turning hand-wheel clockwise to
a full stop.
Hose Check
Before each use, check to see if there is evidence of abrasion, wear, cuts or leaks, the
hose must be replaced prior to the appliance being put into operation. The
replacement hose assembly shall be that specified by the manufacturer.
Cleaning and inspection of pressure regulator and hose assembly prior to use.

TF2014501-RG-00 Eng Page 12 20160930 V.1
Cleaning the Burner
CAUTION
Checking and cleaning burner / venture tubes for insect nests. A clogged tube can
lead to fire beneath the appliances.
Spiders’nests or wasps’mud inside the burner may cause fire at the air damper. If a
fire occurs, immediately turn off gas supply at LP tank valve. (See representative
illustration in Fig.1)
Note:
Spiders and small insects can spin webs and build nests inside the burner. This especially
occurs in late summer and fall before frost when spiders are most active. These nests can
obstruct gas flow and cause a fire in and around the burner and orifice. Such a fire can
cause operator injury and serious damage to the appliance.
To help prevent a blockage and ensure full heat output, clean and inspect burner tube often
(once or twice a month). NOTE: Water or air pressure will not normally clear a spider web.
Steps for Cleaning the Burner:
1. Remove orifice/hose from the burner.
2. Look inside the burner tube for nests, webs, or
mud.
3. To remove the above obstructions, use an
accessory flexible venture brush or bend a small
hook on one end of a long flexible wire such as
the one shown in Fig.2.
4. Inspect and clean the burner if needed.
5. Reattach orifice/hose to burner.

TF2014501-RG-00 Eng Page 13 20160930 V.1
Cleaning and Maintenance
Keep appliance area clear and free from combustible materials, gasoline and other
flammable vapors and liquids.
Do not block holes in bottom or sides of appliance.
Check burner flames regularly.
Use appliance only in well-ventilated space. NEVER use in enclosed space such as
carport, garage, porch, covered patio, or under ANY overhead construction.
Completely thaw meat and poultry prior to placing in hot oil.
To minimize splattering, dry surfaces of meat and poultry prior to placing in hot oil.
When LP tanks is connected to appliance, store outdoors in well-ventilated space and
out of reach of children.
Store appliance indoors ONLY if LP tanks turned off and disconnected, removed form
appliance and stored outdoors.
To keep the appliance clear and free from gasoline and other flammable vapors and
liquids.
Not obstructing the flow of combustion and ventilation air.
Keeping the ventilation opening(s) of the cylinder enclosed free and clear from debris.
CAUTION
All cleaning and maintenance should only be done when the appliance is cool and
with the fuel supply turned off at the LP tank. DO NOT clean any part in a
self-cleaning oven. The extreme heat will damage the finish.
Correct care and maintenance will keep your appliance operating smoothly. Clean regularly
as determined by the amount of use. NOTE: Clean the entire appliance each year and
tighten all hardware on a regular basis (1-2 times a year or more depending on usage).
Cleaning should be done where detergents won’t harm patio, lawn or the like.
Suggested Cleaning Materials:
Mild dish washing liquid detergent
Hot water
Wire brush
Paper clip
Nylon Cleaning pad
Soft brass bristled brush
Component Cleaning:
Burner: Wire brush loose corrosion from burner exterior. Clean clogged gas port holes with
an opened paper clip. Replace corroded or damaged burners that would emit excess gas.
Cooking surfaces, pots and pans: Clean the cooking surface with soapy water and a nylon
cleaning pad.

TF2014501-RG-00 Eng Page 14 20160930 V.1
Part List
Number
Description
1
21”Tall Steel Stand x 1pc
2
Burner x 1pc
3
Regulator x 1pc
4
18QT Pot x 1pc
5
Strainer basket x 2pcs
6
Strainer basket handle x 2pcs
7
5”Thermometer x 1pc
Assembly Procedure
Step 1. Insert the burner into the cooker stand and through the cut-out opening in the side of
the stand.
Step 2. Insert the threaded pin on the bottom of the burner into the center hole in the burner
bracket. Make sure the alignment pin is seated in the notch on the edge of the burner
bracket. Aligned with the burner pins, and secure with the hex nut.

TF2014501-RG-00 Eng Page 15 20160930 V.1
Step 3. Insert the brass hose fitting into the burner and tighten. Be sure not to strip threads
on brass fitting. DO NOT OVERTIGHTEN. Proper connection is critical for correct operation
of unit
Step 4. Attach the handle by inserting bolts through basket, locking washers and nuts.
Step 5. Thread wirer hook through hole on side of regulator.

TF2014501-RG-00 Eng Page 16 20160930 V.1
Step 6. When transporting or storing LP cooker without tank attached, hook regulator onto
burner or cooker stand to prevent damage to regulator.

TF2014501-RG-00 Eng Page 17 20160930 V.1
DANGER
An oil overflow may occur resulting in a fire which could cause property damage,
personal injury or death. Follow directions above to prevent this.
WARNING
Avoid bumping of or impact with the appliance to prevent spillage or splashing of hot
cooking liquid. Introduction of water or ice from any source into the oil/grease may cause
overflow and serve burns from hot oil and water splatter. When frying with oil/grease, all
food products MUST be completely thawed and towel dried before being immersed in
the fryer.
LIMITED WARRANTY
1. Manufacturer warrants this Product to be free from defects in workmanship and
materials for a period of Ninety (90) days from the date of purchase, PROVIDED
claims are submitted, in writing, with proof of purchase.
2. If any part of this item fails because of a manufacturing defect within the Limited
Warranty Period, Manufacturer offers to replace such part(s) provide that such
parts have not been improperly repaired, altered, or tampered with or subject to
misuse, abuse or exposed to corrosive conditions. This Limited Warranty is,
however, subject to certain limitations, exclusions, time limits and exceptions
(Hereinafter “Conditions”) as listed below. Read these Conditions carefully.
3. This Limited Warranty shall be limited to the replacement or repair of any part(s)
which Manufacturer determines, after reasonable examination, to have been
defective at the time of manufacturing and manufacturer’s obligation(s) shall be
limited to replacement, if any, of defective part(s) which shall be shipped at Original
Purchaser’s expense to Original Purchaser’s designated shipping address.
4. This Limited Warranty is given to and covers the ORIGINAL PURCHASER ONLY
and such coverage terminates Ninety (90) days from the date of purchase.
5. DAMAGE LIMITATION WARNING: IN NO EVENT SHALL
MANUFACTURER BE LIABLE FOR ANY INCIDENTIAL OR CONSEQUENTIAL
DAMAGES, INCLUDING (BUT NOT LIMITED TO) LOSS OF USE OF THE
PRODUCT, LOSS OF TIME, INCONVENIENCE, EXPENSES FOR TRAVEL,
TRANSPORTATION LODGING EXPENSES, LOSS BY DAMAGE TO PERSONAL
PROPERTY OR LOSS OF INCOME, PROFITS OR REVENUE.

TF2014501-RG-00 Eng Page 18 20160930 V.1
6. MANUFACTURER’S OBLIGATION: Manufacturer’s liability shall be limited to
the delivery of a good, merchantable Product and, if necessary, the repair or
replacement, at manufacturer’s option, of any defective part or unit.
7. TRANSFER LIMITATIONS: This Limited Warranty is not assignable or
transferable. It covers only the original purchaser.
8. RESERVED RIGHT TO CHANGE: Manufacturer reserves the right to make
changes or improvements to products it produces in the future without imposing on
itself any obligations to install the same improvements in the products it has
previously manufactured.
9. This Limited Warranty gives the Original Purchaser specific legal rights but there
may be other rights which vary by jurisdiction.
10. This warranty does not cover the following items:
A. Chips or scratches on porcelain or painted surfaces
B. Rust or corrosion is not deemed a manufacturing or materials defect
C. Discoloration or loss of paint due to handling during assembly, heat or
cleaning products. Paint may require touch up.
D. Stainless steel discoloration or corrosion
E. Consumables such as batteries
IF CUSTOMER SERVICE BECOME NECESSARY:
1. The Original Purchaser is responsible for shipping and handling
charges of the returned item(s) and replacement parts, if any.
2. All parts to be replaced will need to be shipped before replacement
items will be sent.
3. Follow the Customer Service Representative’s instructions exactly. If
a return is necessary, it must be packed carefully and shipped prepaid.
Should you encounter any problems,
CONTACT US FIRST, DO NOT return product to the store!
RANKAM (CHINA) MANUFACTURING COMPANY LIMITED
18/F., New Lee Wah Centre, 88 Tokwawan Road, Kowloon, Hong Kong
CUSTOMER SERVICE: 1-[phone]
For assistance, contact customer service at
customerserv[email protected]
or at [phone], Mon to Fri, 8:00am –5:00pm Pacific Standard time