Road shower 4 User manual

For one year from date of purchase, Road Shower will repair, help you repair, or replace this

Road Shower, free of charge, if defective in material or workmanship. Service is available by

contacting Road Shower by phone or email and obtaining and Return Merchandise Authoriza-

tion (RMA) before returning a Road Shower to Road Shower, LLC. Units will not be replaced,

refunded, or repaired without an RMA. We will give you the return address with the RMA. Once

you have your RMA, attach to your Road Shower and include your name, address, and tele-

phone number, description of the problem and proof of date of retail purchase (sales slip).

Package and send transportation prepaid to Road Shower, LLC. You may also return Road

Shower to your Road Shower dealer.

Road Shower, LLC shall not be liable for any incidental or consequential damages. Some

states do not allow the exclusion or limitation of implied warranties, incidental or consequen-

tial damages, so the above limitations and exclusions may not apply to you. This warranty does

not cover damage resulting from misuse, abuse, neglect, alteration or modification, improper

installation or operation, failure to tighten mounting hardware, or unauthorized repair or ser-

vice. This warranty does not cover any representation or warranty made by dealers beyond the

provisions of this warranty.

Road Showers out of warranty. Contact us for repair charges. We may be able to ship you the

part that you need. Check our website for parts available from other sources.

The warranty gives you certain legal rights, and you may also have other rights which may vary

from state to state.

Covers Model 4 / 4L / 4S

Safety Rules and Instructions - Read Before Use

Congratulations! You have purchased the finest portable camping shower/water supply on the market

today. This shower uses the renewable energy of the sun to heat the water. Please read this manual.

There are also several instructional videos at www.roadshower.com that will help you get the most

from your Road Shower.

Parts: Each Road Shower comes with the following parts:

• 1 owners manual.

• Mounting hardware which consists of: (4 long carriage bolts, 4 short carriage bolts, and 2 mounting

brackets).

• A spare hose clip.

• LCD thermometer which you can stick onto the tank anywhere you want. Just remove the backing

and stick in on.

• Female to female garden hose connector for filling and pressurizing your Road Shower using your

garden hose.

•

Mounting using the side mounting slot: When mounting to a vertical surface such as a roof

top box, using the side mounting slot, be sure to use at least 3 mounting brackets. The unit

comes with 2 mounting brackets, therefore, you will need to purchase an extra set of brackets

from the spare parts section of our online store. Failure to mount using at least 3 brackets may result

in the mounting bolts tearing through your Road Shower or breaking the mounting bolts. Be sure to

keep them tight or they will break off. This is especially important with the side slot mount.

Be sure to mount the Road Shower securelyand tightly. Check and tighten the mounting

brackets periodically. In addition, always stop and check and tighten mounting brackets while

driving on rough roads. Failure to do so could result in the Road Shower coming off your vehicle during

a quick stop, a sharp turn or an auto accident. This could cause injury to the unit, people or vehicles.

We shall not be liable for any damage caused by units coming off the vehicle.

Fill Cap: Before removing the cap be sure to open the black on/off elbow handle to the horizontal

Road Shower.com

US Patents#8225436 and 9629508

Road Shower Owner’s Manual.

99% of the problems can be handled by obtaining a spare part from us. Just call or email,

and we will get that part to you.

Wrench to tighten fill cap—not really necessary for most people.

On/off elbow with black handle. (This comes pre-taped with plumbers tape. Thread into the outlet

hole carefully to not strip the threads. Tighten with a wrench until firm and the outlet points out. If it

leaks, try to tighten 1 more turn. If it won’t tighten anymore, remove and add some plumbers tape

and try again). Attach hose.

Mounting: Road Shower comes with 2 mounting brackets. Each bracket is

secured with 2 carriage bolts. You will find 8 carriage bolts; 4 are extra. Use

either the long ones, if you have a thick rack, or the short ones if you have a

thinner rack. Use the hole that is in the center of the slot to install the bolts.

Slide the bolts down the slot in the Road Shower so that a bolt is on either

side of your cross bar. You may want to apply some tape over the bar where

the Road Shower will rest to protect the paint. Put the mounting bracket curved side up and line the bolts

up through the holes in the bracket. Secure with the nylock nuts. If reusing the nuts use some lock wash-

ers. Lube the bolt to prevent “galling”, which stainless steel bolts and nylock nuts are susceptible too.

(Seizing = galling.) Use a 1/2” wrench or a socket wrench to tighten the nuts. They should be very tight.

Once both brackets are secure, push and pull on the Road Shower sideways, and see if it slips along the

bar. If it slips, tighten more. Be sure to use lock washers if you reuse the nylock nuts more than a few times.

Check our website for current telephone number

Email: info@roadshower.com | Website: www.roadshower.com

Road Shower LLC

Santa Fe, NM - only online sales.

This safety alert symbol indicates important safety messages in this manual. When you see this

symbol, be alert to the possibility of personal injury and carefully read the message that follows.

Road Shower is manufactured in China and was invented, designed and engineered in the US.

Pressurizing with your garden hose: You can fill and pressurize the Road Shower by attaching your

garden hose to the unit’s hose. Remove the spray nozzle first. Attach a female to female garden hose

connector. Make sure the black handle is open. Turn on your garden hose. After a minute or so, check

the pressure on the Schrader valve with a tire pressure gauge. Turn off the incoming hose water when

pressure reaches 65 PSI. If your home water pressure is less than 65 PSI, you will not need to check

the pressure. Just fill until the water stops flowing. You are filled up and pressurized!

Pressurizing with a pump: Road Shower works OK with pres-

sure created from gravity, as long as you loosen the fill cap. How-

ever to get the most out of your Road Shower, it should be pres-

surized. Each Road Shower comes with a built in air cham-

ber. You can fill it all the way up with water, and there will

still be air space to add the compressed air. Pumping options

include a12 volt tire compressor, a hand bicycle pump or a CO2

cartridge pump. Make sure the fill cap is on securely by hand

tightening. If the cap is leaking pressure, tighten with included

wrench, or add some white plumbing tape to the threads.

This product releases pressure at a target of 65 PSI. If the pressure relief valve on the fill cap is

damaged or is altered, the Road Shower could explode and cause injury and possibly death.

Check pressure while pumping air and never pressurize greater than 75 PSI. If the pressure is not

releasing before it reaches 75 PSI, the fill cap should be replaced.

Use only with clean clear water to prevent clogging the pressure relief valve. Do not fill with

fuel or other substances.

Heating the water: The Road Shower will heat water on a warm sunny day. The sun heats the black

surface on the outside. The aluminum transfers the heat to the water. The water heats up as long as

the tube is receiving sunlight from any angle. The water temperature rises 10-15F degrees per hour on

a warm sunny day. If your water starts at 60 degrees, it might be 90+ degrees in about 2-3 hours.In

general, the water will be about 20 — 30 degrees warmer than the ambient temperature if it is a sunny

day after a few hours.

Burn warning and thermometer: On a hot and sunny summer day that is 95F+, the water

inside this product could exceed 120 degrees, which could scald the user. Water in the

product’s reservoir may be hotter than the water in the hose. Check the thermometer. The high-

est reading is 116F, so if there is no reading, than possibly the

water is too hot. Always test spray water on palm of your hand

for 10 seconds to check if it is too hot. If the water is too hot,

you can add some cool water via the fill cap or wait until it cools.

Water level: You can check the water by looking at the water

level through the clear hose. To be able to see it, loosen the fill

cap, hold the spray nozzle above the tank, and pull the spray

nozzle trigger. Or use a small stick as a dip stick through the fill

cap opening.You cannot check the water while it is pres-

surized.

Parking on a hill. If your car is parked on a hill, it should be parked with the outlet on the downhill

end, in order to use all the water. Each Road Shower comes with the option to add another outlet on

the opposite end (sold separately). This allows the hose to be moved to the outlet on the lowest end.

You could add a quick release to the hose and elbow for quickly moving the hose.

Shower head: (Sold separately). It features a low flow shower head

with a flex neck. It can be attached to your outlet with included quick

connects. It makes hands free showering easy.

Spray Nozzle: The spray nozzle can be adjusted to a variety of spray

patterns. Just rotate the tip of the nozzle to adjust the shower spray to

jet setting. If the tip is completely tight, no water will come out. You

can also remove the nozzle and run the water from the hose alone. Be

sure to attach the nozzle prior to travel by using the hose clip and

Velcro.

Freeze Damage Caution: Do not leave water in the Road Shower during freezing temperatures as it

could damage your unit. Do not put RV antifreeze in the unit; keep it drained during freezing tempera-

tures.

Privacy. You can purchase a shower enclosure for privacy.

Car Wash: A car wash can damage the unit and your vehicle. We shall not be liable for any

damage caused by a car wash.

Parking Garages: Your Road Shower may not have enough clearance for some parking ga-

rages or your own garage. Know the height of your vehicle with a Road Shower so you can

check it before entering a parking garage. We shall not be liable for any damage caused by en-

tering spaces with inadequate clearance.

Locking: Road Shower comes with a loop welded to the elbow end.

You can lock your Road Shower to your rack with a cable or chain as

shown in this picture. We also sell a locking cable that does not re-

quire a lock. Simply attach and put the opposite end of the cable

inside your car door and lock your car.

Sanitize and clean for drinking water: You may use Road Shower

for drinking water as the aluminum and the food grade poly hose are

non-toxic. Wash the storage container with dishwashing soap and

water and rinse completely with clean water. Fill tank with 5 gallons

water. Add 1/2 cup of bleach. Cover the container and shake it well (or drive a few minutes) so that the

sanitizing bleach solution touches all inside surfaces of the container. Wait at least 30 seconds and

then pour the sanitizing solution out of the container. Rinse the empty container with clean, safe water.

Due to the corrosive nature of bleach on the metal hose ends, remove the hose and nozzle after rinsing

with clean water and spray some cooking oil spray inside the hose ends after they dry. For drinking water

use, sanitize once per year.

Road Shower Owner’s Manual. Covers Model 4 / 4L / 4S

Maintenance: When storing, empty the tank completely. Store with the elbow open and the hose off

and the fill cap off so it dries out. Tighten all screws, mounting hardware, and fittings on a regular ba-

sis. Clean the unit with soap and water. Spray on auto wax works well to preserve the powder coat

finish from sun damage. Remove the hose and store inside to prevent hose discoloration.

Capacity: Road Shower 4S -4 gallons, Road Shower 4 -7 gallons, and Road Shower 4L-10 gallons.

You can fill it with a hose or a water jug through the fill cap opening.

position and pull the nozzle trigger to release any pressure . Then slowly unscrew the fill cap. If there is

excess pressure, it will begin to hiss. Do not unscrew more until the hissing stops