ROBAND ET22 User manual

MANUFACTURED BY
ROBAND AUSTRALIA PTY LTD
ASSEMBLY INSTRUCTIONS
STAINLESS STEEL FOOD BAR TROLLEYS &
PANELS
Models: ET22, ET23, ET24, ET25 & ET26
ETP22, ETP23, ETP24, ETP25 & ETP26
Version 2 Units
These instructions cover the models of ROBAND
®
Stainless steel trolleys and
panels listed above. Although there are slight variances between them, the
installation, operation, care and maintenance procedure is the same for all.

Page
2
Quantities
Note: As illustrated some parts are pre-assembled
Parts No.’s/Contents
ET22
ET23
ET24
ET25
ET26
Diagrams
Pre Assembled bag
Packed in castor box
1 1 1 1 1
4 x DC0103
4 x DC0104
8 x PC0326
4 X MS0427– 455mm
Vertical Frame (preassembled)
4 x DC0103
4 x DC0104
4 x MC0761
4 4 4 4 4
4 X MS0428- 504.5mm
Short Horizontal frame
(preassembled)
8 x DC0105
8 x MC0084
4 4 4 4 4
4 X MS0390-MS0394
Long Horizontal Frame
(preassembled)
8 xDC0105
8 x MC0084
4 4 4 4 4
SS2131
Small Shelf Panel 2 2 2 2 2
SS2130
Large Shelf Panel 0 1 2 3 4
MC0151
Locking Castors 2 2 2 2 2
MC0150
Plain Castors 2 2 2 2 2
5mm Allen Key
Packed in castor box
1 1 1 1 1

Page
3
INSTALLATION
Remove all the packaging materials and tape, as well as any protective
plastic from the unit. Clean off any glue residue left over from the protective
plastic using methylated spirit. Do not remove the double-sided adhesive
tape at this stage.
Tools
To assemble the trolley the following tools are required.
•Rubber or wooden mallet.
•Allen Key. (Supplied in kit)
Please note: If you use a metal hammer, place a block of wood on the
metal parts and strike the wood to prevent damage to the metal parts.
ET24 Step-by-Step Instructions
Instructions are the same for every model, but the frame sizes and number of
panels differs.
1. Organise the frame to resemble below
(Please note that all the Horizontal bars should have end fittings screwed into either end of
them.)
MS0428
MS0427
MS0392

Page
4
2. Select the 3 bars above labelled above and start to assemble the trolley frame. Insert
the joiner into the vertical leg of the trolley (labelled MC0427) the flat straight side of the
joiner should face to the front. The legs should fit tightly into the joiner you may need so
use the mallet to gently tap into place.
3. Once in place, the joiner cover can be inserted on, the same way the legs were
inserted on to the joiner. The blanking plug is also inserted now. This is placed in the
spare joiner circle, to cover up the spare joiner hole. Don’t screw together yet.

Page
5
4. Now that this corner of the frame is together, connect the 3 other corners this way.
Again not screwing them together.
5. Insert Joiners into the other end of the vertical bars again making sure the joiners flat
ends are flush.

Page
6
6. As in the previous steps attach the joiners and blanking plug to the corners. Now
attach the castors using the screws provided. Use the Allen key to tighten the screws as
in the following diagram. Note that the screws for the castors will form their own thread
as they are screwed into the legs. Note that two of the castors include a locking device
these should be assembled on one long side of the trolley usually the side on which the
operator serves from.

Page
7
7. Now flip the trolley over carefully, and insert the screws into the top joiner covers, and
tighten. Again, the screws will form their own thread in the extruded legs as the screw
is tightened.
Your trolley frame should now be tightly secured together and resemble the
diagram below.

Page
8
Inserting Shelf Panels
ET series trolleys are supplied with the shelf panels. Refer to page 1 for quantities. Note
that ETI series trolleys do not have shelf panels supplied.
Note: If you have purchased ETP panels with your trolley then assemble those panels
first, before you install the shelf panels. Refer to page 9 for this step and return to this
step after the ETP panels have been installed.
1. Wipe down the trolley frame removing any excess machine oil.
2. Peel the plastic protective coating off the shelf panels.
3. Place the smaller outer shelf panels (300mm wide) in place first. If your trolley has been
supplied with additional larger shelf panels (325mm wide) then place them in between the
outer panels to complete the shelf. These panels do not require any fixing the simply lay in
position on the trolley frame. Refer to the image below.

Page
9
ETP Series optional panels.
Note: All ETP panels are supplied with double sided tape to fix them in position. This
tape should be stuck to the trolley frame rail at the top of the frame not to the rail closest
to the castors.
1. Wipe down the trolley frame removing any excess machine oil.
2. The end panels are inserted into the trolley frame first. Below is a picture of the
end panel inserted in position. The panels should slot into the frame neatly with
the flanges of the panel sitting square with the trolley frame.
3. Insert the front panels in the same manner but do not stick them down yet.
Install the smaller outer panels (300mm wide) first. If your ETP set has been
supplied with additional larger panels (325mm wide) then place them in between
the outer panels. These panels have been designed to have a 1mm gap on either
side of each panel once installed. Before you stick them in position, arrange them
so that this clearance is achieved and hold them temporarily in place with some
sticky tape. Once you are happy with their positions, use the supplied double sided
tape to stick them permanently one at a time.
ET Series panels ETP Series panels (charges additional)
Size
Shelf
Outer
Panels
Shelf
Centre
Panels
End Panels Front Outer
Panels
Front Centre
Panels
22 2 - 2 2 -
23 2 1 2 2 1
24 2 2 2 2 2
25 2 3 2 2 3
26 2 4 2 2 4

Page 10
The Dark Panels illustrate
how the front and end panels
rest on the trolley frame.
3. Lastly, fit the shelf panels in place. Refer to page 8.

Page 11
NOTES
This page is intentionally left blank. Please note your favourite settings here.

Page 12
NOTES
This page is intentionally left blank. Please note your favourite settings here.