Robert Juliat ARTHUR User manual

Robert Juliat S.A.S. 32, rue de Beaumont, F 60530 Fresnoy-en-Thelle - phone : [phone] - [email protected]
www.robertjuliat.com
800 W FOLLOWSPOTS
1014TC / 1014TCLT TOP CONTROL
1014 / 1014LT
LED FOLLOWSPOTS
DN41195800-B
VALIDATION : 18/09/23
V1
- FIRMWARE: V2.07
Manual
Angles Controls
Model
Standard / CE North American
5.5° – 15° On the side 1014 1014C
5.5° – 15° On top 1014TC 1014CTC
Angles Controls
Model
Standard / CE North American
4° – 10° On the side 1014LT 1014CLT
4° – 10° On top 1014TCLT 1014CTCLT

Robert Juliat reserve the right to change or alter any of the items detailed on this page,
to increase or improve manufacturing techniques without prior notice.
Table of Contents
1 User’s instructions............................................................................................................... 1
2 Presentation ........................................................................................................................ 2
2.1 Functions................................................................................................................... 2
2.2 Identication label ................................................................................................... 3
2.3 Accessories included ................................................................................................ 3
2.4 Accessories ................................................................................................................ 4
3 Set-up ................................................................................................................................... 5
3.1 Mechanics ................................................................................................................. 5
3.1.1 Operating positions ................................................................................................... 5
3.1.2 Minimum distance between a ammable material and the lighting unit.... 5
3.1.3 Instructions for use...................................................................................................... 5
3.1.4 Handling........................................................................................................................ 5
3.1.5 Lifting ............................................................................................................................. 5
3.1.6 Yoke adjustment .......................................................................................................... 6
3.1.7 Stand set-up.................................................................................................................. 6
3.2 Electrical information .............................................................................................. 7
3.2.1 LED source..................................................................................................................... 7
3.2.2 Power supply................................................................................................................. 7
3.3 DATA........................................................................................................................... 8
3.3.1 DMX 512-A / RDM........................................................................................................ 8
3.3.2 Art-Net / sACN .............................................................................................................. 9
3.4 Accessories .............................................................................................................. 10
3.4.1 Full closing iris cassette ............................................................................................10
3.4.2 Colour changer unit - boomerang ........................................................................10
3.4.3 Colour changer unit - push-pull (option).............................................................11
3.4.4 Gobo holder................................................................................................................ 11
3.4.5 Frosted / Correction lter (option) ......................................................................... 12
3.4.6 Internal glass holder 120 x 120 mm (option)...................................................... 12
3.4.7 Stands (option)...........................................................................................................13
3.4.8 Telrad followspot sight (option)............................................................................. 13
3.4.9 RJ cable strap..............................................................................................................13
3.4.10 Flight-case (option).................................................................................................14
4 Operations ......................................................................................................................... 15
4.1 Light intensity ......................................................................................................... 15
4.1.1 Range ....................................................................................................................................15
4.1.2 Control..................................................................................................................................15
4.1.3 Parameters........................................................................................................................... 15
4.1.3.1 Dimming resolution - DMX only.........................................................................15
4.1.3.2 Dimming curve .......................................................................................................15
4.1.3.3 Master control.........................................................................................................16
4.1.3.4 Set maximum position.......................................................................................... 16
4.1.3.5 Dimming mode.....................................................................................................166
4.2 Strobe....................................................................................................................... 17
4.2.1 Range............................................................................................................................17
4.2.2 Control .........................................................................................................................17
4.3 Response time......................................................................................................... 17
4.3.1 Range............................................................................................................................17
4.3.2 Control .........................................................................................................................17
4.4 Beam size adjustment............................................................................................ 18
4.4.1 Range............................................................................................................................18
4.4.2 Control .........................................................................................................................18
4.5 Pan / Tilt................................................................................................................... 19
4.5.1 Range............................................................................................................................19
4.5.2 Control .........................................................................................................................19
4.6 Iris............................................................................................................................. 20
4.6.1 Range............................................................................................................................20
4.6.2 Control .........................................................................................................................20
4.7 Gobo ........................................................................................................................ 20
4.7.1 Range............................................................................................................................20
4.7.2 Control .........................................................................................................................20
4.8 Colour ...................................................................................................................... 21
4.8.1 Range............................................................................................................................21
4.8.2 Control .........................................................................................................................21
4.9 Frost and correction lters .................................................................................... 22
4.9.1 Range............................................................................................................................22
4.9.2 Control .........................................................................................................................22
5 Controls and parameters ................................................................................................ 23
5.1 Local display and controls..................................................................................... 23
5.1.1 Display..........................................................................................................................23
5.1.2 Home screen ............................................................................................................... 23
5.1.3 Menu............................................................................................................................. 24
5.1.4 Parameters .................................................................................................................. 25
5.1.4.1 Intensity.......................................................................................................... 25
5.1.4.2 Auto-OFF ........................................................................................................25
5.2 DMX512 - A remote control................................................................................... 26
5.2.1 Protocol .......................................................................................................................26
5.2.2 Conguration ............................................................................................................26
5.2.3 Parameters .................................................................................................................26
5.2.3.1 DMX Hold .......................................................................................................26
5.2.4 DMX chart ................................................................................................................... 27
5.2.5 DMX ranges ................................................................................................................ 27
5.2.5.1 Strobe duration.............................................................................................27
5.2.5.2 Strobe speed ..................................................................................................27
5.2.5.3 Response time ...............................................................................................27
5.2.5.4 Control mode ................................................................................................27
5.3 RDM remote control............................................................................................... 28
5.3.1 Protocol........................................................................................................................ 28
5.4 Art-Net remote control .......................................................................................... 30
5.4.1 Protocol .......................................................................................................................30
5.4.2 Conguration ............................................................................................................30
5.5 sACN remote control .............................................................................................. 31
5.5.1 Protocol........................................................................................................................ 31
5.5.2 Conguration ............................................................................................................31
5.6 Fan cooling modes ................................................................................................. 32
5.6.1 Range............................................................................................................................32
5.6.2 Control .........................................................................................................................32
5.7 Local potentiometer............................................................................................... 33
5.8 Web interface.......................................................................................................... 34
5.8.1 Control .........................................................................................................................34
5.8.2 Default IP address......................................................................................................34
5.8.3 Network IP of the computer .................................................................................... 34
5.8.4 Connect to web interface.........................................................................................34
6 Service ................................................................................................................................ 35
6.1 Preventive maintenance........................................................................................ 35
6.1.1 Frequency....................................................................................................................35
6.1.2 General cleaning........................................................................................................35
6.1.3 General visual check ................................................................................................35
6.1.4 LED source...................................................................................................................35
6.1.5 Optics............................................................................................................................35
6.1.6 LED house cleaning................................................................................................... 36
6.2 Analysis ................................................................................................................... 37
6.3 Electronic thermal management system............................................................. 37
6.4 Firmware update .................................................................................................... 37
6.5 Factory defaults...................................................................................................... 37
6.6 Selftest ..................................................................................................................... 38

EN
EN - 1 -
GENERAL INSTRUCTIONS
1. Not for residential use.
2. These fixtures must only be serviced by a qualified technician.
3. In addition to the instructions indicated on this page, relevant health and safety requirements of the appropriate EU
Directives must be adhered to at all times.
4. This fixture is in compliance with section 17 - Lighting appliance for theatre stages, television, cinema and photograph studios.
Standards NF EN 60598-1, NF EN 60598-2-17, Low Voltage Directive 2014/35/UE & EMC Directive 2014/30/UE.
5. This fixture is rated as IP20, and is for indoor use only.
FIXTURE
6. Ensure fixture is correctly mounted on an appropriate support.
7. Protection screens and lenses must be replaced in the event of any damage, such as cracks or deep scratches, since these might
reduce performance.
8. When hung or flown the fixture must be secured by an additional hanging accessory (such as a safety cable or bond) of suitable
length.
9. Safety bonds or cables must be securely attached to the back of the fixture and be as short as possible, or rolled up as necessary,
to minimise travel distance should the fixture be dislodged.
10. Movable accessories (scroller, etc.) must also be secured with a suitable safety cable or bond at the front of the fixture.
11. The combined weight of both the fixture and the accessories must be considered when choosing the load-bearing capability of
safety cable or bond.
12. Do not open lighting fixture when the source is on.
13. WARNING: LED source become hot during use. Allow fixture to cool before servicing.
14. Do not tamper with design of fixture nor any of its safety features.
15. Tighten electrical mains cable connections regularly and replace with one of identical specification if damaged.
16. Use only with correct power supply.
VENTILATION
17. Keep well away from flammable material.
18. Not for outdoor use. Do not cover. Do not permit fixture to get wet.
19. To avoid overheating, do not obstruct air vents.
20. Ensure any cooling fans are in correct working order. If fans are not working, turn fixture off immediately and service as necessary.
CLEANING
21. Do not touch the LED source with your fingers.
22. To clean the optical parts, use a soft cloth in combination with distilled water or isopropyl alcohol recommended for coated optics.
Do not use any cleaning product that contains solvents or abrasives, as these can cause surface damage. Dry with a soft lint-free cloth.
23. Regularly remove dust with a soft lint-free cloth.
24. If the fixture has filters, they must be cleaned frequently.
POWER SUPPLY
25. Disconnect from the mains before servicing.
26. Mains connection only. Do not connect to "electronic output" such as dimmer.
27. Ensure power supply circuit breakers, always remain accessible.
PLEASE NOTE
This product has been built to conform to European standards relating to professional lighting equipment.
Any modification made to our products will void the manufacturers' warranty.
1 User’s instructions
Risk group 2
CAUTION: Possibly hazardous optical
radiation emitted from this product.
Do not stare at operating lamp.
Maybe harmful to the eye.
Minimum
distance
Risk
group 2
- 50m (164 ft )
Risk
group 1
Photobiological safety according to EN62471
X1 X2
Group risk 2. Luminaires should be positioned so that prolonged
staring into luminaire at a distance closer than 50m is not expected.

EN
9
7
5
3
11
13
21
110
8
6
4
4* 5*
12
2
17
19 15 18
14
20
16
22
23
EN - 2 -
2 Presentation
2.1 Functions
Functions
1 Yoke
2 Tilt locking handle
3 Side operating handle
4 Iris control (1014/1014LT only)
4* Iris control (1014TC/1014TCLT only)
5 Dimming control (1014/1014LT only)
5* Dimming control (1014TC/1014TCLT only)
6 Colour changer
7 Zoom adjustment
8 Focus adjustment
9 Frost glass
10 Spare filter
11 Gobo holder
12 Local display
13 Keypad
14 Identification plate
15 Data connectors (OUT and IN)
16 Power connectors (IN and OUT)
17 Power switch (thermal breaker)
18 USB connectors for accessories
19 RJ45 connectors
20 Cable lock
21 Handles
22 Lifting rings
23 Tilt stopper

EN
EN - 3 -
2.2 Identication label
1 2
3
45 5*
8 9
7
6 6*
2.3 Accessories included
Reference Description
1 CAL03 3 meter power cable ( 3G1,5 HO7RNF) with Neutrik PowerCon© True1 TOP
and CEE 7/7 (2P+T NF/SCHUKO) connectors (standard version)
2 CAL04 1,50m power cable UL/CSA with Neutrik®powerCON TRUE1 TOP connector
(North American version)
3 DN41195900 Quick Start manual
4 PF1013 Ø270 mm metal filter holder (x6)
5 CCU1 Full closing iris cassette - Ø72 mm
5* CCU2 Full closing iris cassette - Ø55 mm for LT version
6 SGUP2 Universal "A" size gobo-holder (metal & glass)
6* SGUB3 "B" size gobo-holder (metal & glass) for LT version
7 VDM120 Ø120 mm frosted glass with holder
8 M270/2B 6-way "boomerang" colour changer
9 SAC1 RJ cable strap (25 x 500 mm) (x1)
Description
Units :
- Weight = kilogram (kg).
- Intensity = Ampere (A).
- Voltage = Volt (V).
- Frequency = Hertz (Hz).
- Temperature = degree Celsius (°C).
1. MOD. : Model
2. VERS. : Version
3. U : Nominal voltage input (V)
4. I : Nominal intensity (A)
5. P : Maximum power input (W)
6. IP : International Protection Rating
7. t°a : Maximum ambient temperature (°C)
8. t°c : Maximum external temperature of the unit (°C)
9. Net weight (kg)
10. Minimum distance between a flammable
material and the lighting unit (m)
11. LED type
12. Serial number
13. Replace broken glass
14. Class 1 product label
15. Read manual first label
16. European conformity label
17. WEEE directive label
18. CEI-TR-62778 - Do not stare at light source
19. EN62471 - Risk group
20. UKCA (UK Conformity Assessed) label
1 2
34
5 6
7 8
9
10
11
12
13 14
18 15 16 2019 17

EN
EN - 4 -
2.4 Accessories
Reference Description
1 JPP Monopod stand for overhead followspot
2 GT4000 Tripod stand with safety chain - SWL: 130 Kg - max. height: 1030 mm
3 GT4000S Tripod stand without safety chain - SWL: 130 Kg - max. height: 1030 mm
4 GT4000R Tripod stand with ball head rotation with security chain - SWL: 130 Kg - max. height: 1030 mm
5 T4000 Followspot mount for Ø50 mm pipe (suspension or overhead) - SWL= 100 Kg
6 VD120 120 x 120 mm frosted glass
7 FCM120/2 Ø120 mm 1/2 CTO correction filter (Rosco #3408) with holder
8 M270/2TM 6-way "Push/Pull" colour changer
9 Kit TELRAD Telrad followspot sight with raiser and universal mounting kit
10 SDUP Followspot cue sheet holder with universal mounting kit
11 FC1014/S Flight-case for LLT range / GT stand / accessories
12 GT4000RSM Tripod stand with safety chain - SWL: 130 Kg - max. height: 1030 mm
(equipped with PAN sensor)
13 CCU1SM Full closing iris cassette with position sensor for SpotMe system Ø72 mm
13* CCU2SM Full closing iris cassette with position sensor for SpotMe system Ø55 mm for LT version
14 SMS SpotMe server + 2 sensor cables + flight case
15 T4000RSM Followspot mount with ball head rotation and SpotMe PAN sensor
SWL = 100 Kg - Weight: 8,83 Kg
16 FRO/SMCPD Heavy duty adjustable yoke equipped with TILT SpotMe sensor (C type)
17 TCSM SpotMe calibration tool kit
18 Maestro Maestro server for SpotMe - rackable unit: 1U - half 19"
19 PCP1716A 16A blue 2P+E 6h IEC60309 power connector (option)
20 G80/2 Ø80 mm horizontal chopper
6
78
11
19 20
10
9
13 13*
1 2 3 54
12
14
15
1716
18

EN
EN - 5 -
3 Set-up
3.1 Mechanics
3.1.1 Operating positions
3.1.2 Minimum distance between a ammable material and the lighting unit
3.1.3 Instructions for use
Minimum : 40°C
104°F
5°C
40°F
IP20 - Indoor use only
Maximum :
3.1.5 Lifting
• Net weight:
68.8 Kg (151.4 Ibs)
3.1.4 Handling
1.3 m / 4.3 ft
1014 & 1014TC
0.8 m / 2,6 ft
1014LT & 1014TCLT
Side view
Overhead view
Overhead view
Lifting rings

EN
EN - 6 -
3.1.7 Stand set-up
• GT4000 / GT4000S / GT4000R
Please refer to the relevant stand technical files for further details.
Dimension in mm.
3.1.6 Yoke adjustment
The unit must be installed only on a Robert Juliat compatible stand / head :
JPP Monopod stand for overhead followspot
GT4000 Tripod stand with safety chain - SWL: 130 Kg - max. height: 1030 mm
GT4000S Tripod stand without safety chain - SWL: 130 Kg - max. height: 1030 mm
GT4000R Tripod stand with ball head rotation with security chain - SWL: 130 Kg - max. height: 1030 mm
T4000 Followspot mount for Ø50mm pipe (suspension or overhead) - SWL= 100 Kg
GT4000RSM Tripod stand with ball head rotation with safety chain and SpotMe PAN sensor -
SWL: 130 Kg - max. height: 1030 mm
T4000RSM Followspot mount with ball head rotation and SpotMe PAN sensor -
SWL= 100 Kg
Caution: Slighty untighten the
screws without removing them
to set yoke position.
Remove screw to set desired
position, then tighten.
Caution:
Remove followspot from stand to set yoke position.
Open out the
tilt stopper
Caution:
Place one of the stand legs towards the front to
support the maximum tilt position.

EN
2
1
In Out
Daisy chain:
EN - 7 -
Power supply
Voltage Frequency Input power Connectors
100 T240 V 50-60 Hz
4,3 A / 960 W @ 230V
8,7 A / 1030 W @ 120V
10,7 A / 1080 W @ 100V
Neutrik powerCON TRUE1 TOP
Input :
ref. NAC3FPX-TOP
3.2 Electrical information
3.2.1 LED source
Never touch or scratch the LED surface.
Cf. 6.1.4 LED cleaning procedure if cleaning is necessary.
3.2.2 Power supply
Power cable
Power cable Connector Mains plug Cable type Cable length Wiring
1 Standard
version Neutrik®
powerCON
TRUE1 TOP
NAC3FX-W-TOP
CEE7/7 3G1.5
H07RNF
3 m
9.8 ft
Live: Brown
Neutral: Blue
Ground: Yellow/Green
2
North
American
version
-
14AWG
SJ TYPE
(UL/CSA)
1.5 m
4.9 ft
Live: Black
Neutral: White
Ground: Green
• Class 1 product. This luminaire must be earthed.
• Must be connected directly to AC power. Do not connect to dimmer power.
• Automatic mains voltage detection.
Power
Maximum :
3 units @ 230V
1 unit @ 120V
1 unit @ 100V

EN
EN - 8 -
DATA connectors
PIN # DMX Description
1Shielding Foil & Braided Shield
2DMX (-) 1st conductor of 1st twisted pair
3DMX (+) 2nd conductor of 1st twisted pair
4Not used 1st conductor of 2nd twisted pair
5Not used 2nd conductor of 2nd twisted pair
3.3 DATA
3.3.1 DMX 512-A / RDM
Protocol Input connector Output connector
USITT DMX 512-A
RDM XLR 5-pin XLR 5-pin
Power ON
Maximum :
32 units total
Daisy chain:
1
2
2
3
34
4
5
5
1

EN
Daisy chain:
EN - 9 -
Protocol Input connector Output connector
Art-Net
sACN RJ45 #1 RJ45 #2
Protocol Input connector Output connector
Art-Net
sACN RJ45 #1 or #2 -
3.3.2 Art-Net / sACN
• With external switch
Network
switch*
Art-Net
sACN
Daisy chain:
• With integrated switch
all units must be powered
Art-Net
sACN
(*) A 1000 base-T switch that supports IGMP (Internet Group Management Protocol) is necessary if the unit is connected
to a network switch to control multiple devices. The usage of non IGMP switch capability can cause erratic behavior of all
connected devices.
For further reading: https://en.wikipedia.org/wiki/Internet_Group_Management_Protocol
Integrated switch specifications: 100 base-T unmanaged

EN
Dimensions Cf. 4.8.1
EN - 10 -
3.4 Accessories
3.4.1 Full closing iris cassette
3.4.2 Colour changer unit - boomerang
2
1
2
1
1
(1014TC & 1014TCLT)
(1014 & 1014LT)

EN
3.4.4 Gobo holder
'A' size gobo
Dimensions Cf. 4.7.1
'B' size gobo (LT version)
Dimensions Cf. 4.7.1
Dimensions Cf. 4.8.1
EN - 11 -
3.4.3 Colour changer unit - push-pull (option)

EN
EN - 12 -
3.4.6 Internal glass holder 120 x 120 mm (option)
3.4.5 Frosted / Correction lter (option)
Dimensions Cf. 4.9.1

EN
EN - 13 -
3.4.8 Telrad followspot sight (option)
3.4.7 Stands (option)
• GT4000 Series : Please refer to the relevant stand technical files for further details.
Stand set-up, refer to Cf. 3.1.7
3.4.9 RJ cable strap
Caution: - Do not install the followspot sight on the lamp house to avoid blocking the ventilation vents.
- Secure the sight with a suitable safety cable.
Followspot sight
guide available @
www.robertjuliat.com/followspots/
Accessories
x1 standard supply

EN
EN - 14 -
3.4.10 Flight-case (option)
Inner overhead view
Accessories
compartment
GT4000 stand
compartment
Inner side view
GT4000 stand
compartment

EN
0% 100%
DMX512-A
EN - 15 -
4 Operations
4.1 Light intensity
4.1.1 Range
4.1.2 Control
Remotely with DMX512-A protocol Locally via dimming control handle Locally via Standalone mode
Art-Net / sACN
4.1.3 Parameters
4.1.3.1 Dimming resolution - DMX only
4.1.3.2 Dimming curve
Tselection in SETUP / DIMMER / CURVE menu: LINEAR or SQUARE
HTP mode (Highest Takes Precedence):
Light output is the highest value of DMX512 command or local control
Resolution DMX mode
8 bits – 255 steps 1 - 3 - 5
16 bits – 65 535 steps 2 - 4 - 6
Tselection in
DATA MODE / PROTOCOL /
STANDALONE
(1014TC & 1014TCLT)
(1014 & 1014LT)

EN
EN - 16 -
4.1.3.3 Master control
TDMX Mode 5 / 6
In order to supervise the operator from the console, master control DMX channel can be used.
This channel limits the maximum value of the dimmer shutter.
By using this function, it is possible to obtain synchronised fades with several spots or to give intensity
limits (minimum and maximum) to the operator . Master is only active when DMX is detected.
4.1.3.4 Set maximum position
TSelection in SETUP / DIMMER / MAX menu
4.1.3.5 Dimming mode
TSelection in SETUP / DIMMER / DIMMING MODE menu
100%
100%
0% 0%
----> Maximum (80%)
Light Output
Mode Result
Without PWM Flicker-Free, perfect for filming
PWM 20 KHz Good dimming quality (Default Value)
PWM 3,2 KHz Very good dimming

EN
X ms
DMX 0 = 0 ms
1 = 100 ms
255 = 4000 ms
DMX512-A
DMX512-A
EN - 17 -
4.3 Response time
4.3.1 Range
Mode Speed
NONE OFF
SLOW 700 ms
MEDIUM 470 ms
FAST 350 ms
CUSTOM 0 - 4000 ms
4.3.2 Control
Remotely, with
DMX512-A / Art-Net / sACN protocols
Mode 3 – 4 – 5 – 6
Locally, only when no DMX detected or
DMX 512-A/Art-Net/sACN protocols
Mode 1 + 2
Tselection in
SETUP / DIMMER / RESPONSE TIME
4.2 Strobe
4.2.1 Range
Strobe duration
Strobe speed
4.2.2 Control
Remotely with
DMX512-A / Art-Net / sACN protocols
Mode 3 – 4 – 5 – 6
0 = OFF
0 = 0.1Hz
1 = 1ms 255 = 20ms
255 = 10Hz

EN
EN - 18 -
Model Angles Minimum angle Maximum angle
ARTHUR
1014 & 1014TC
Beam angle 5.4° 13.2°
Field angle 5.8° 13.6°
ARTHUR
1014LT & 1014TCLT
Beam angle 4.1° 10°
Field angle 4.5° 10.6°
Beam angle
50%
Field angle
3%
4.4 Beam size adjustment
4.4.1 Range
ZOOM ZOOMFOCUSFOCUS
1 12 2
4.4.2 Control
22
11