Chauvet COLORado 1 User manual

Snapshot
OK on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
115V/230V Switch
Replaceable Fuse
User Serviceable
Duty Cycle
COLORado™1
USER MANUAL
Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com

TABLE OF CONTENTS
1. BEFORE YOU BEGIN....................................................................................................................................................... 3
WHAT IS INCLUDED.............................................................................................................................................................. 3
UNPACKING INSTRUCTIONS.................................................................................................................................................. 3
AC POWER ......................................................................................................................................................................... 3
CONTACT US...................................................................................................................................................................... 3
SAFETY INSTRUCTIONS........................................................................................................................................................ 4
2. INTRODUCTION ............................................................................................................................................................... 5
FEATURES .......................................................................................................................................................................... 5
DMX CHANNEL SUMMARY................................................................................................................................................... 5
PRODUCT OVERVIEW .......................................................................................................................................................... 6
3. SETUP............................................................................................................................................................................... 7
FUSE REPLACEMENT........................................................................................................................................................... 7
FIXTURE LINKING................................................................................................................................................................. 7
Data Cabling ................................................................................................................................................................. 7
DMX Data Cable.................................................................................................................................................... 7
Cable Connectors.................................................................................................................................................. 8
3-Pin to 5-Pin Conversion Chart............................................................................................................................ 8
SETTING UP A DMX SERIAL DATA LINK ................................................................................................................................8
MASTER/SLAVE FIXTURE LINKING ........................................................................................................................................ 9
MOUNTING.......................................................................................................................................................................... 9
Orientation............................................................................................................................................................. 9
Rigging................................................................................................................................................................... 9
4. OPERATING INSTRUCTIONS........................................................................................................................................ 10
NAVIGATING THE CONTROL PANEL..................................................................................................................................... 10
MENU MAP........................................................................................................................................................................ 11
MENU FUNCTIONS............................................................................................................................................................. 12
User Configurations.................................................................................................................................................... 12
Programming Custom Scenes............................................................................................................................. 12
Upload custom programs to another fixture: ....................................................................................................... 13
Activate or Deactivate the password: .................................................................................................................. 13
Service Functions ....................................................................................................................................................... 13
Reset custom programs to factory defaults......................................................................................................... 13
OPERATION....................................................................................................................................................................... 13
Stand-Alone Mode (Auto Mode): ................................................................................................................................ 13
Master/Slave Mode (Master Auto):............................................................................................................................. 14
DMX Mode.................................................................................................................................................................. 14
DMX-512 control without “ID” address........................................................................................................................ 14
DMX-512 addressing with ID address ........................................................................................................................ 14
EXAMPLE CONFIGURATIONSDMX CHANNEL VALUES .......................................................................................................... 15
DMX CHANNEL VALUES .................................................................................................................................................... 16
5. COLORADO™ CONTROLLER ...................................................................................................................................... 19
OVERVIEW ........................................................................................................................................................................ 19
SETUP .............................................................................................................................................................................. 19
MENU MAP........................................................................................................................................................................ 20
Wash Program............................................................................................................................................................ 20
Effect Program............................................................................................................................................................ 20
Custom Program......................................................................................................................................................... 21
Play Schedule............................................................................................................................................................. 21
Clock........................................................................................................................................................................... 21
Schedule..................................................................................................................................................................... 21
Settings....................................................................................................................................................................... 21
Activating password mode.......................................................................................................................................... 22
Control via external DMX............................................................................................................................................ 22
GENERAL TROUBLESHOOTING ........................................................................................................................................... 24
TECHNICAL SUPPORT........................................................................................................................................................ 25
6. APPENDIX....................................................................................................................................................................... 25
DMX PRIMER.................................................................................................................................................................... 25
PHOTOMETRICS ................................................................................................................................................................ 26
GENERAL MAINTENANCE ................................................................................................................................................... 27
RETURNS PROCEDURE...................................................................................................................................................... 27
CLAIMS............................................................................................................................................................................. 27
TECHNICAL SPECIFICATIONS.............................................................................................................................................. 28
COLORado 1 User Manual 2 2008-01-18/16:45

1. BEFORE YOU BEGIN
What is included
¾1 x COLORado™ 1
¾1 x Power cable with plug
¾1 x IP65 power extension cable
¾1 x IP65 signal extension cable
¾1 x DMX input cable
¾1 x DMX output cable
¾Warranty Card
¾Users Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
This fixture has an auto-switching power supply that can accommodate a wide range of input
voltages. The only thing necessary to do before powering on the unit is to make sure the line voltage
you are applying is within the range of accepted voltages. This fixture will accommodate between
100V and 240V AC. All fixtures must be powered directly off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for
a 0% to 100% switch.
Contact Us
World Wide
General Information Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com
COLORado 1 User Manual 3 2008-01-18/16:45

Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.
xPlease keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
xAlways make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
xMake sure there are no flammable materials close to the unit while operating.
xAlways disconnect from power source before servicing or replacing fuse and be sure to replace with
same fuse source.
xSecure fixture to fastening device using a safety chain.
xMaximum ambient temperature (Ta) is 95°F (35°C). Do not operate fixture at temperatures higher
than this.
xIn the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
xDon’t connect the device to a dimmer pack.
xMake sure the power cord is never crimped or damaged.
xNever disconnect the power cord by pulling or tugging on the cord.
xAvoid direct eye exposure to the light source while it is on.
xDo not daisy chain power to more than 20 units at 120V, or 40 units at 230V.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
COLORado 1 User Manual 4 2008-01-18/16:45

DMX Channel Summary
CHANNEL FUNCTION
1Master Dimmer
2Red
3Green
4Blue
Master Dimmer
Red
Green
Blue
5Color Macros
6Strobe
7Auto/Custom Programs
8ID Address
9Instant/Delayed Color Change
STAG CHANNEL FUNCTION
1
2
Red
3
Green
Blue
ARC
CHANNEL FUNCTION
1
2
3
4
ARCd
2. INTRODUCTION
Features
x9-channel DMX-512 LED PAR can (with ID addressing)
xBlackout/static/dimmer/strobe/pulse
xRGB color mixing with or without DMX controller
xBuilt-in automated programs via master/slave, DMX or COLOR-CON
xProgram and recall custom programs via master/slave, DMX or COLOR-CON
xRGB fade delay channel for snapping or fading
Additional Features
xAvailable in black or silver
xDurable and weather resistant IP65 rated
xAdditional power output for daisy chaining units together (max 20 units @ 120V)
xLED display with lock-out feature
xGel frame holder (4mm max thickness)
xLow power consumption
Optional Controller
xCOLORado™ Controller (COLOR-CON)
COLORado 1 User Manual 5 2008-01-18/16:45

Product Overview
Power In
Connector Power Out Connector
DMX In
Connector DMX Out
Connector
Control
Panel
Hanging
Bracket
Gel frame
(optional
accessory)
Tilt
Adjustment
Knob
COLORado 1 User Manual 6 2008-01-18/16:45

3. SETUP
Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.
Fuse Replacement
The fuse for this fixture is located inside the chassis. Remove the damaged fuse from its holder and
replace with exact same type fuse. Reconnect power.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To
comply with the EIA-485 standard no more than 32 devices should be
connected on one data link. Connecting more than 32 fixtures on one serial
data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX DATA CABLE
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor and shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
COLORado 1 User Manual 7 2008-01-18/16:45

CABLE CONNECTORSCABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
2
13OUTPUT
Termination reduces signal errors. To
avoid signal transmission problems
and interference, it is always
advisable to connect a DMX signal
terminator.
1
3
2
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
1
3
2
DMX-
DMX
+
COMMON
DMX connector configuration
INPUT
CAUTION Do not allow contact between the common and the fixture’s chassis
ground. Grounding the common can cause a ground loop, and your fixture may
perform erratically. Test cables with an ohm meter to verify correct polarity and to
make sure the pins are not grounded or shorted to the shield or each other.
CAUTION Do not allow contact between the common and the fixture’s chassis
ground. Grounding the common can cause a ground loop, and your fixture may
perform erratically. Test cables with an ohm meter to verify correct polarity and to
make sure the pins are not grounded or shorted to the shield or each other.
3-PIN TO 5-PIN CONVERSION CHART3-PIN TO 5-PIN CONVERSION CHART
Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5
pin to 3 pin adapter. CHAUVET Model No: DMX5M, or DMX5F.
The chart below details a proper cable conversion:
Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5
pin to 3 pin adapter. CHAUVET Model No: DMX5M, or DMX5F.
The chart below details a proper cable conversion:
3PIN TO 5PIN CONVERSION CHART3PIN TO 5PIN CONVERSION CHART
ConductorConductor 3 Pin Female (output)3 Pin Female (output) 5 Pin Male (Input)5 Pin Male (Input)
Ground/Shield Pin 1 Pin 1
Data ( - ) signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use
Universal DMX Controller
Setting up a DMX Serial Data Link
COLORado 1 User Manual 8 2008-01-18/16:45
This drawing provides a
general illustration of the
DMX Input/Output panel of
alightingfixture.
1. Connect the (male) 3 pin connector side of
the DMX cable to the output (female) 3 pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female) 3
pin connector to the input connector of the
next fixture consisting of a (male) 3 pin
connector.
3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.
CHAUVET Certified DMX Data Cables
Order Code Description
DMX1.5 DMX Cable 1.5m/4.9ft
DMX4.5 DMX Cable 4.5m/14.8ft
DMX10 DMX Cable 10m/32.8ft Continue the link

Master/Slave Fixture Linking
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.
Often, the setup for Master-Slave
and Standalone operation requires
that the first fixture in the chain be
initialized for this purpose via either
settings in the control panel or DIP-
switches. Secondarily, the fixtures
that follow may also require a slave
setting. Please consult the
“Operating Instructions” section in
this manual for complete instructions
for this type of setup and
configuration.
Mounting
ORIENTATION
This fixture may be mounted in any position provided there is adequate room for ventilation.
RIGGING
Hanging Clamp
It is important never to obstruct the fan or vents pathway. Mount the
fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the
fixture by loosening both knobs and tilting the fixture. After finding the
desired position, retighten both knobs.
xWhen selecting installation location, take into consideration lamp
replacement access and routine maintenance.
xSafety cables must always be used. Note!
Clamp is sold separatel
y
.
xNever mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
COLORado 1 User Manual 9 2008-01-18/16:45

4. OPERATING INSTRUCTIONS
Navigating the Control Panel
Access control panel functions using the four panel buttons located directly underneath the LCD
Display.
UP DOWNSETMENU
Button Function
<MENU> Used to access the menu or to return to a
previous menu option
<SET> Used to select and store the current menu
or option within a menu
<UP> Scrolls through menu options in ascending
order
<DOWN> Scrolls through menu options in descending
order
The Control Panel LED Display shows the menu items you select from the menu map on page #.
When a menu function is selected, the display will show immediately the first available option for the
selected menu function. To select a menu item, press <SET>.
Press the <MENU> button repeatedly to scroll through the top level menu items. This is the top of the
menu map. Use the <UP> and <DOWN> buttons to navigate the menu map and menu options. Press
the <SET> button to access the menu function currently displayed or to enable a menu option. To
return to the previous option or menu without changing the value, press the <MENU> button.
COLORado 1 User Manual 10 2008-01-18/16:45

Menu Map
AUTO When navigating the menu:
Use the “UP” button to move up.
Use the “DOWN” button to move down.
Use the “SET” button to move right.
Use the “MENU” button to move left.
dMX
Edit
SET
PASS
AT.01 – AT.10
(Automatic 1-10)
d001 – d512
rEd
GrEn
TIME
bluE
Strb
FAdE
PR.C1 – PR.10
(Custom 1-10)
UPLd
REST
OFF
ON
ARC
STAG
ARCd
PR.C1 - PR.10
(Custom 1-10)
SC.01 – SC.30
(Scene 1-30)
Id I001 – I066
(ID Address)
R.000 – R.255
G.000 – G.255
T.000 – T.255
b.000 – b.255
S.000 – S.255
F.000 – F.255
PASS
PASS
****
****
Send
rEST
End
PERS
SLAv
DMX
MODE
COLORado 1 User Manual 11 2008-01-18/16:45

Menu Functions
MENU
OPTION DESCRIPTION
AUTO
Auto Mode – Master Unit: Sets the fixture to Master status for
Master-Slave operation and the built in programs will be
triggered by the sound. No data link is required; all fixtures
can be set to this mode for Stand-alone operation.
dMX
DMX Mode: Sets the fixture to run in DMX mode. Also, this mode
is used to set a fixture to operate in Slave mode. In
Master/Slave mode you must set the first fixture in the data
link to “Master” otherwise nothing will happen.
Id ID Address: Sets the ID address of the fix
t
ure, which allows up
to 3,696 (66 per DMX address) COLORado 1 fixtures to be
independently controlled on one universe.
Edit Used to create and edit custom programs. Up to 10 custom
programs with up to 30 steps (scenes) each can be programmed.
SET Used to upload the custom programs from one fixture to another,
and to reset the custom programs to the factory defaults.
PASS Turns the password protection on or off. If turned on, you must
enter a password to gain access to the control panel.
PERS Allows the user to select the DMX personality of the fixture. To determine the personality required for your application
please reference the DMX value tables in the pages that follow.
MODE Allows user to toggle between DMX and slave modes. Slave mode is also selected when the unit is being controlled by the
COLORcon controller system.
User Configurations
PROGRAMMING CUSTOM SCENES
In order to create a custom program than can be run in any mode, do the following:
1) In the menu, select “Edit”. Next, scroll through until the desired program number is displayed,
and select it.
2) Scroll through to the step you wish to program, and select it.
Note: The program runs in sequential order, starting with step 01, and continuing through step 30. To
program less than 30 scenes, set the [Step time] of the scene after your last scene to 0.
3) “rEd” will be displayed on the screen. Press <SET> to edit the value for red. Scroll through to the
red value you wish to program, and select it by pressing <SET>. Repeat this for the, “GrEn”,
“bluE”, “Strb”, “TimE”, and “FAdE” values. Note that “TimE” is the length of time in minutes that
the current step will run, and must be a value between 0 and 255. “Fade” is the amount of time,
in seconds, that the fixture will take to gradually transition between the previous step and the
current step. If the value of “Fade” is 0, the transition will be at the maximum speed possible.
4) Repeat steps 2 and 3 until the program is created.
5) To end programming, press <MENU> twice.
The program can be run in any mode. See the instructions for the desired operating mode in order to
run the custom program.
COLORado 1 User Manual 12 2008-01-18/16:45

UPLOAD CUSTOM PROGRAMS TO ANOTHER FIXTURE:
1) On all fixtures that are going to receive the custom programs from the source unit, set them for
DMX operation; address does not matter for the purpose of this operation.
2) On the Master unit, press <MENU> until “SET” is displayed, and press <SET>.
3) Scroll through until “UPLd” is displayed, and press <SET>.
4) “PASS” will now be displayed. Press <SET>, and the display will go blank, except for a single
dot.
5) Press <UP>, then <DOWN>, then <UP>, then <DOWN>, then <SET>. This is the same
password that is used for the main access password.
6) “SENd” will now be displayed, and all units will output the color yellow.
7) When the upload is complete, the sending fixture will display “ENd”, and all fixtures will output
the color green to indicate a successful upload. If a unit has an error, it will output the color red.
8) Press <MENU> on the source unit to exit the upload mode.
ACTIVATE OR DEACTIVATE THE PASSWORD:
1) Press <MENU> until “PASS” is displayed, and press <SET>.
2) Select “OFF” or “ON” and press <SET>.
Note: The password is permanently set as <UP>,<DOWN>,<UP>,<DOWN>; this cannot be
changed.
Service Functions
RESET CUSTOM PROGRAMS TO FACTORY DEFAULTS
1) Press <MENU> until “SET” is displayed, and press <SET>.
2) Scroll through until “REST” is displayed, and press <SET>.
3) “PASS” will now be displayed. Press <SET>, and the display will go blank, except for a single
dot.
4) Press <UP>, then <DOWN>, then <UP>, then <DOWN>, then <SET>. This is the same
password that is used for the main access password.
5) “REST” will now be displayed, and will be flickering. After about 30 seconds, the reset sequence
will be complete, and “REST” will be displayed without flickering.
6) Press <MENU> to exit the reset mode.
Operation
Stand-Alone Mode (Auto Mode):
This mode allows a single unit to auto change in Auto Mode.
1) Press <MENU> until “Auto” appears on the display, and press <SET>.
2) Press scroll through to the desired program (either Auto 1-10 or Custom 1-10), and press <SET>
to select it. The unit will now auto change in Auto Mode.
COLORado 1 User Manual 13 2008-01-18/16:45

Master/Slave Mode:
This mode will allow you to link up to 32 units together without a controller.
1) Use standard DMX cables to daisy chain your units together via the DMX connector on the rear
of the units. For longer cable runs we suggest a terminator at the last fixture. For more
information about terminators, see page 8.
2) Choose a unit to function as the Master. The unit must be the first unit in line. Press <MENU>
until “Auto” appears on the display, and press <SET>.
3) Press scroll through to the desired program (either Auto 1-10 or Custom 1-10), and press <SET>
to select it.
4) Then simply chain the units together using DMX cable.
5) Nothing needs to be set on the slave units. So long as they are in any top-level menu they
should respond to a DMX controller or Master fixture.
DMX Mode
This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, please read the DMX Primer on page 24.
1) Press <MENU> until “dMX” is displayed and press <SET>.
2) Scroll through to select the desired address, and press <SET>.
DMX-512 control without “ID” address
The COLORado™ 1 operates on 3-9 channels of DMX. Address each fixture in increments of 3-9
channels. (I.e. 1, 10, 19, 28 etc…) To save time you can use the same DMX address for each fixture.
All fixtures will then respond simultaneously to control. You may also group your fixtures and address
those groups alike for faster programming and control.
1) Press <MENU> until “dMX” is displayed and press <SET>.
2) Scroll through to select the desired address, and press <SET>.
Note: This fixture always has an ID address; it cannot be deactivated. Unintended results
may occur if values are present in channel 8. Make sure values on channel 8 are set
to “0”.
DMX-512 addressing with ID address
1) Press <MENU> until “dMX” is displayed and press <SET>.
2) Scroll through to select the desired DMX address, and press <SET>.
3) Press <MENU> until “Id” is displayed and press <SET>.
4) Scroll through to select the desired ID address, and press <SET>. For every DMX512 starting
address the user can set 66 separate ID addresses.
Note: ID addresses are accessible using Channel 8.
COLORado 1 User Manual 14 2008-01-18/16:45

Example Configurations
ID Address: 01 ID Address: 02 ID Address: 03 ID Address: 04 ID Address: 05 ID Address: 06
The figure above shows 6 fixtures connected in series with corresponding
addresses. You must set the {Range} settings in the controller to [006] before
accessing {Effect} programs.
UP DOWN EXITSET
Single Row
Application
ID Address: 01
The figure above shows 9 fixtures
connected in series with
corresponding addresses. You must
set the {Range}settingsinthe
controller to [009] before accessing
{Effect} programs.
UP DOWN EXITSET
Block Application
ID Address: 02 ID Address: 03
ID Address: 04 ID Address: 05 ID Address: 06
ID Address: 07 ID Address: 08 ID Address: 09
ID Address: 01
The figure above shows 9 fixtures connected
in series. Three rows comprised of 3 fixtures
are addressed identically. You must set the
{Range} settings in the controller to [003]
before accessing {Effect} programs.
ID Address: 02 ID Address: 03
ID Address: 01 ID Address: 02 ID Address: 03
ID Address: 01 ID Address: 02 ID Address: 03
Repeat Row Block Application
UP DOWN EXITSET
COLORado 1 User Manual 15 2008-01-18/16:45

DMX Channel Values (ARC Mode)
CHANNEL VALUE FUNCTION
1000 255 Red (or step time when PR. 01 – PR. 10 is activated)
0 – 100%
2000 255 Green (or fade time when PR. 01 – PR. 10 is activated)
0 – 100%
3000 255 Blue
0 – 100%
DMX Channel Values (ARCd Mode)
CHANNEL VALUE FUNCTION
1000 255 Master Dimmer: 0 – 100%
2000 255 Red (or step time when PR. 01 – PR. 10 is activated)
0 – 100%
3000 255 Green (or fade time when PR. 01 – PR. 10 is activated)
0 – 100%
4000 255 Blue
0 – 100%
DMX Channel Values (STAG Mode)
CHANNEL VALUE FUNCTION
1000 255 Master Dimmer: 0 – 100%
2000 255 Red (or step time when PR. 01 – PR. 10 is activated)
0 – 100%
3000 255 Green (or fade time when PR. 01 – PR. 10 is activated)
0 – 100%
4000 255 Blue
0 – 100%
5
000 009
010 029
030 039
040 049
050 069
070 079
080 089
090 109
110 119
120 129
130 149
150 159
160 169
170 189
190 199
200 219
220 229
230 239
240 255
Color Macros
No function
Red
Red 85%, Yellow 15%
Red 60%, Yellow 40%
Yellow
Yellow 85%, Green 15%
Yellow 60%, Green 40%
Green
Green 85%, Blue 15%
Green 60%, Blue 40%
Blue
Blue 85%, Cyan 15%
Blue 60%, Cyan 40%
Cyan
Cyan 50%, Purple 50%
Purple
Purple 50%, White 50%
White 95%, Yellow 5%
White
6000 009
010 063
064 127
Strobe
No function
Strobe with pulse effect (slow > fast)
Strobe (slow > fast)
COLORado 1 User Manual 16 2008-01-18/16:45

128 191
192 255 Color changing pulse with fadeout (slow > fast)
Color changing pulse with fade-in/out (slow > fast)
7
000 009
010 019
020 029
030 039
040 049
050 059
060 069
070 079
080 089
090 099
100 109
110 119
120 129
130 139
140 149
150 159
160 169
170 179
180 189
190 199
200 255
Programs
No function
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Auto 9
Auto 10 (Cycle Auto 1 – 9 for 5 minutes each)
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5
Custom 6
Custom 7
Custom 8
Custom 9
Custom 10
8
000 009
010 019
020 029
030 039
040 049
050 059
060 069
070 079
080 089
090 099
100 109
110 119
120 129
130 139
140 149
150 159
160 169
170 179
180 189
190 199
200 209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
ID Address
All IDs
ID 1
ID 2
ID 3
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
ID 10
ID 11
ID 12
ID 13
ID 14
ID 15
ID 16
ID 17
ID 18
ID 19
ID 20
ID 21
ID 22
ID 23
ID 24
ID 25
ID 26
ID 27
ID 28
ID 29
ID 30
ID 31
ID 32
ID 33
ID 34
ID 35
ID 36
ID 37
ID 38
ID 39
ID 40
ID 41
ID 42
COLORado 1 User Manual 17 2008-01-18/16:45

232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
ID 43
ID 44
ID 45
ID 46
ID 47
ID 48
ID 49
ID 50
ID 51
ID 52
ID 53
ID 54
ID 55
ID 56
ID 57
ID 58
ID 59
ID 60
ID 61
ID 62
ID 63
ID 64
ID 65
ID 66
9000 250
251 255
RGB Fader Response
Instant (snap)
5 second fade
COLORado 1 User Manual 18 2008-01-18/16:45

5. COLORADO™CONTROLLER
Overview
LCD Display Panel
MODE SETUP UP DOWN
MODE Accesses main menu or backs out of sub-menu
SETUP Selects the currently displayed menu or confirms the current function value
UP Use to navigate upwards through menu items or increment function values
DOWN Use to navigate downwards through menu items or decrement function values
Setup
Connect from the OUT on the controller to the DMX Input side of the COLORado™ 1 using a DMX XLR
cable. It is recommended that you power up all COLORado units connected prior to turning on the
controller. This ensures that the controller will auto-detect DMX addresses.
Alternatively you can use {Detect device} from the {Settings} menu.
Set ID addresses on the COLORado’s in ascending order.
Set the {Range} in the {Settings} menu.
Note There is no need to set ID and Range for {Wash} programs.
COLORado 1 User Manual 19 2008-01-18/16:45

Menu Map
MAIN
FUNCTION SELECTION SELECTION SELECTION SELECTION
Step time
[001] [255]
Wash
program
Wash [1]
Wash [8] Edit Fade time
[001] [255]
Effect
program
Effect [1]
Effect [8] Edit Speed
[001] [100]
ID address [000*] [100]
(*0 = all units)
Step time [000] [255]
Fade time [000] [255]
Red [000] [255]
Green [000] [255]
Blue [000] [255]
Module [001] [006]
Custom
program
Custom [1]
Custom [8] Edit Scene [1] Scene [100]
Strobe [000] [020]
Play
schedule Schedule
Time now I.e.
12/31/2006
13:50:24
Clock
Edit time I.e. 12/31/2006
13:50:24
Wash [1]
Wash [8]
Effect [1]
Effect [8]
Schedule
Custom [1]
Custom [8]
Start>>>End
00:00>>00:00
DMX address [001] [255]
Range [001] [066]
Allow edit [YES] [NO]
Detect device >>>
Settings
Reset to
Factory
settings [YES] [NO]
Password
ON/OFF [ON] [OFF]
Password Set password [ ]
Wash Program
1) Select from the eight existing [Wash] programs and it will instantly play.
2) Set the [Step time] and the [Fade time] in the [Edit] function if desired.
3) The unit of time is 5 seconds and it can be adjusted between 1 and 255.
Effect Program
1) Select from the eight existing [Effect] programs and it will instantly play.
2) Vary the [Speed] of the effect between 1 and 255.
Note: effect programs were designed primarily for the COLORado 3. They will work with the
COLORado 1, but they may react differently from time to time.
COLORado 1 User Manual 20 2008-01-18/16:45