Robert Juliat OZ 1169 User manual

600W LED FOLLOWSPOTS
FOLLOWSPOTS
VALIDATION: 28/09/18
DN41145300-B
OZ & ALICE
Quick Start Guide
Model Standard North American
7 – 14,5° OZ 1169 OZ 1169C
13 – 24° ALICE 1469 ALICE 1469C
Robert Juliat S.A.S. 32, rue de Beaumont, F 60530 Fresnoy-en-Thelle - phone : [phone] - fax : [phone] - [email protected]
www.robertjuliat.com
User's manual: Technical file: Included:
For more information and updates:
www.robertjuliat.com/followspots/followspots.html
CAL03 OR CAL04
SGUP
x6
VDM100
DN41145300-A PF1011
CCU1
Oz - 1169 v1a / Alice - 1469 v1a

EN
EN
EN - 2 -
GENERAL INSTRUCTIONS
1. Not for residential use.
2. These fixtures must only be serviced by a qualified technician.
3. In addition to the instructions indicated on this page, relevant health and safety requirements of the appropriate EU
Directives must be adhered to at all times.
4. This fixture is in compliance with section 17 - Lighting appliance for theatre stages, television, cinema and photograph
studios. Standards NF EN 60598-1, NF EN 60598-2-17, Low Voltage Directive 2014/35/UE & EMC Directive 2014/30/UE.
5. This fixture is rated as IP20, and is for indoor use only.
FIXTURE
6. Ensure fixture is correctly mounted on an appropriate support.
7. Protection screens and lenses must be replaced in the event of any damage, such as cracks or deep scratches, since
these might reduce performance.
8. When hung or flown the fixture must be secured by an additional hanging accessory (such as a safety cable or bond) of
suitable length.
9. Safety bonds or cables must be securely attached to the back of the fixture and be as short as possible, or
rolled up as necessary, to minimise travel distance should the fixture be dislodged.
10. Movable accessories (scroller, etc.) must also be secured with a suitable safety cable or bond at the front of the fixture.
11. The combined weight of both the fixture and the accessories must be considered when choosing the load-bearing
capability of safety cable or bond.
12. Do not open lighting fixture when the source is on.
13. WARNING: LED source become hot during use. Allow fixture to cool before servicing.
14. Do not tamper with design of fixture nor any of its safety features.
15. Tighten electrical mains cable connections regularly and replace with one of identical specification if damaged.
16. Use only with correct power supply.
VENTILATION
17. Keep well away from flammable material.
18. Not for outdoor use. Do not cover. Do not permit fixture to get wet.
19. To avoid overheating, do not obstruct air vents.
20. Ensure any cooling fans are in correct working order. If fans are not working, turn fixture off immediately and service as
necessary.
CLEANING
21. Do not touch LED source with fingers.
22. Clean all optical parts with alcohol-based cleaner.
23. Clean all filters regularly.
POWER SUPPLY
24. Disconnect from the mains before servicing.
25. Mains connection only. Do not connect to "electronic output" such as dimmer.
26. Not for outdoor use. Do not cover.
27. Ensure power supply circuit breakers, always remain accessible.
PLEASE NOTE
These products have been built to conform to European standards relating to professional lighting equipment. Any modification
made to our products will void the manufacturers' warranty.
1 User’s instructions
2 Installation
Risk group 2
CAUTION: Possibly hazardous optical
radiation emitted from this product.
Do not stare at operating lamp.
Maybe harmful to the eye.
Dimensions in mm.
• GT4000 / S
Please refer to the relevant user manual for further details.

EN
EN - 3 -
4 Electrical / Data connections
1 2 3 4 5 6 7 8
3 Functions
Functions
1. Yoke
2. Yoke locking
3. Side operating
4. Iris control
5. Dimming control
6. Colour changer
7. Focus adjustment
8. Zoom adjustment
9. Frost glass
10. Spare filter
11. Gobo holder
12. Local display
13. Identification plate
14. Data connectors (OUT and IN)
15. Power connectors (IN and OUT)
16. Thermal breaker
17. Power switch
18. Control board
19. Wireless DMX antenna (option)
20. USB connector
21. RJ45 connector
22. Cable lock
1 Switch Power ON / OFF
2 Power input Connector: Neutrik®powerCON TRUE1 Max. 16A.
3 Power output Connector: Neutrik®powerCON TRUE1 Max. 8A.
4 Fuse Thermal breaker: 10A. automatic switch
5 Data Out Connector: XLR 5-pin
6 Data In Connector: XLR 5-pin / Protocol: USITT DMX 512-A RDM
7 Ethernet Connector: RJ45 / Protocol Art-Net, sACN + software updating
8 Auxiliary out Connector: USB (Not for charging purpose)

EN
A
B4
5
2
1
3
FOCUSZOOM
AB
FOCUSZOOM
AB
4 4
5
EN - 4 -
4 Operation
1 Switch on the followspot by pressing the ON / OFF power button.
2 Open the colour changer unit to let the light beam out.
3 Use the manual dimming control to adjust the light intensity.
4 The light beam zoom and focus can be set by using the control knobs A & B.
5 The beam size can be adjusted by using the iris cassette.
0% 100%
PLEASE NOTE
This product has been built in conformity with the European Standards in relation to professional lighting equipment.
Any modification made to our product will void the manufacturers' warranty.
Robert Juliat reserves the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.