Robert Juliat SULLY 650SX 4C User manual

200 W LED
4-COLOUR LED PROFILE SPOT
REF Standard North American
28 - 54° 653SX 4C 653CSX 4C
16 - 35° 654SX 4C 654CSX 4C
11 - 26° 651SX 4C 651CSX 4C
Quick Start Guide
User's manual: Included:
For more information and updates:
www.robertjuliat.com
CAL03 OR CAL04
D8 (x4)SGUXPF500M2
DN41222600
Quick
Start
Guide
www.robertjuliat.com
DN41222600-A (EN)
Robert Juliat S.A.S. 32, rue de Beaumont, F 60530 Fresnoy-en-Thelle - phone : [phone] - [email protected]
VALIDATION : 17/ 0 5/ 2 3
V2
Robert Juliat reserves the right to change or alter any of the items detailed in this document, to increase or improve manufacturing techniques without prior notice.

ENEN
Net weight:
653SX 4C = 12.8 kg (28.2 lbs)
654SX 4C = 14.1 kg (31,1 lbs)
651SX 4C = 14.5 kg (32 lbs)
EN - 2 -
1 User’s instructions
2 Installation
GENERAL INSTRUCTIONS
1. Not for residential use.
2. These fixtures must only be serviced by a qualified technician.
3. In addition to the instructions indicated on this page, relevant health and safety requirements of the appropriate EU
Directives must be adhered to at all times.
4. This fixture is in compliance with section 17 - Lighting appliance for theatre stages, television, cinema and photograph studios.
Standards NF EN 60598-1, NF EN 60598-2-17, Low Voltage Directive 2014/35/UE & EMC Directive 2014/30/UE.
5. This fixture is rated as IP20, and is for indoor use only.
FIXTURE
6. Ensure fixture is correctly mounted on an appropriate support.
7. Protection screens and lenses must be replaced in the event of any damage, such as cracks or deep scratches, since these might
reduce performance.
8. When hung or flown the fixture must be secured by an additional hanging accessory (such as a safety cable or bond) of suitable
length.
9. Safety bonds or cables must be securely attached to the back of the fixture and be as short as possible, or rolled up as necessary,
to minimise travel distance should the fixture be dislodged.
10. Movable accessories (scroller, etc.) must also be secured with a suitable safety cable or bond at the front of the fixture.
11. The combined weight of both the fixture and the accessories must be considered when choosing the load-bearing capability of
safety cable or bond.
12. Do not open lighting fixture when the source is on.
13. WARNING: LED source become hot during use. Allow fixture to cool before servicing.
14. Do not tamper with design of fixture nor any of its safety features.
15. Tighten electrical mains cable connections regularly and replace with one of identical specification if damaged.
16. Use only with correct power supply.
VENTILATION
17. Keep well away from flammable material.
18. Not for outdoor use. Do not cover. Do not permit fixture to get wet.
19. To avoid overheating, do not obstruct air vents.
20. Ensure any cooling fans are in correct working order. If fans are not working, turn fixture off immediately and service as necessary.
CLEANING
21. Do not touch the LED source with your fingers.
22. To clean the optical parts, use a soft cloth in combination with distilled water or isopropyl alcohol recommended for coated optics.
Do not use any cleaning product that contains solvents or abrasives, as these can cause surface damage. Dry with a soft lint-free cloth.
23. Regularly remove dust with a soft lint-free cloth.
24. If the fixture has filters, they must be cleaned frequently.
POWER SUPPLY
25. Disconnect from the mains before servicing.
26. Mains connection only. Do not connect to "electronic output" such as dimmer.
27. Ensure power supply circuit breakers, always remain accessible.
PLEASE NOTE
This product has been built to conform to European standards relating to professional lighting equipment.
Any modification made to our products will void the manufacturers' warranty.
Risk group 2
CAUTION: Possibly hazardous optical
radiation emitted from this product.
Do not stare at operating lamp.
Maybe harmful to the eye.
Group risk 2. Luminaires should be positioned so that prolonged
staring into luminaire at a distance closer than 18,7m (651SX 4C),
8m (653SX 4C) & 13,5m (654SX 4C) is not expected.

EN
2
1
3
4
1Power
input
Connector: Neutrik® powerCON TRUE1 TOP Max. 16A.
Power input: 100 => 264V 50/60Hz.
Must be connected directly to AC power.
Do not connect to dimmer power
Power consumption:
@ 230V 50Hz = 0.88 A / 175 W
Max: 2.1 A
2Power
output
Connector: Neutrik®powerCON TRUE1 TOP Max. 8A.
Daisy chain – Maximum quantity of units on the same
power line:
8 units @ 230V
3 Data Out Connector: XLR 5-pin
4 Data In Connector: XLR 5-pin / Protocol: USITT DMX 512-A RDM
1
3
2
4
12
6
5
11
8
18
19
7
17
10
15
13
14
16
9
1
EN - 3 -
4 Electrical / Data connections
Description
1. Identification plates
2. Data connector (IN and OUT)
3. Power connector (IN and OUT)
4. Local display and controls
5. Handle
6. Safety cable attachment point
7. Hanging yoke
8. Tilt index
9. Tilt locking handle
10. Shutters
11. Shutter locking system
12. Lens tube rotation locking button
13. Lens tube access
14. Focus adjustment
15. Front slot for accessories and gel frame holder
16. Front slot locking system
17. Zoom adjustment
18. Gobo holder
19. Iris
3 Functions

EN
EN - 4 -
C
5 Operation
6 DMX Chart & Source Type
C
3
2
A
AB
B
FOCUS
ZOOM FOCUS
ZOOM
DMX Channel
Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6
Dimmer8B Profile16b Full - XY Full - HS Full - RGB Full - Raw
1 Dimmer Dimmer Dimmer Dimmer Dimmer Dimmer
2 Dimmer fine Dimmer fine Dimmer fine Dimmer fine Dimmer fine
3 Strobe duration Strobe duration Strobe duration Strobe duration Strobe duration
4 Strobe speed Strobe speed Strobe speed Strobe speed Strobe speed
5 Response time Response time Response time Response time Response time
6 Control mode Control mode Control mode Control mode Control mode
7 Source Type Source Type Source Type Source Type
8 Gel: Type Gel: Type Gel: Type Gel: Type
9 Gel: Reference Gel: Reference Gel: Reference Gel: Reference
10 Gel: Saturation Gel: Saturation Gel: Saturation Gel: Saturation
11 Gel: Transmission Gel: Transmission Gel: Transmission Gel: Transmission
12 Gel: Fade Time Gel: Fade Time Gel: Fade Time Gel: Fade Time
13 Gel: Fade Mode Gel: Fade Mode Gel: Fade Mode Gel: Fade Mode
14 Tunable white: CCT Tunable white: CCT Tunable white: CCT Tunable white: CCT
15 Tunable white: CCT fine Tunable white: CCT fine Tunable white: CCT fine Tunable white: CCT fine
16 Tunable white: Delta UV Tunable white: Delta UV Tunable white: Delta UV Tunable white: Delta UV
17 Colour: X Colour: Hue Colour: Red Colour: Red
18 Colour: X fine Colour: Hue fine Colour: Red fine Colour: Red fine
19 Colour: Y Colour: Saturation Colour: Green Colour: Green
20 Colour: Y fine Colour: Saturation fine Colour: Green fine Colour: Green fine
21 Colour: Blue Colour: Blue
22 Colour: Blue fine Colour: Blue fine
23 Colour: Lime
24 Colour: Lime fine
Range min Range max Source type
0 10 Tungsten 3200 K High Quality - DimShift
11 20 Tungsten 3000 K High Quality - DimShift
21 30 Tungsten 3200 K High Quality
31 40 Tungsten 3000 K High Quality
41 50 Daylight D65 High Quality
51 100 Not used
101 110 Generic CCT - High Quality
111 120 Generic CCT - High Brightness
121 130 Generic CCT - High Quality - DimShift
131 140 Generic CCT - High Brightness - DimShift
141 200 Not used
201 210 Colour Mix - High Quality
211 220 Colour Mix - High Brightness
221 255 Not used
Zoom
Focus
1
2
1
2
B
A
1
D
1 Switch on the prole by connecting power cable.
2 The light beam zoom and focus can be set by
using the control knobs A & B.
3 Beam adjustments can also be made by using
the shutters C and the zoom rotation D.