ROBINHOOD RG6WH User manual

RG - SERIES
APPROVED Page 1 of 9
ISSUE: F
ECN 07 033
GRANGE RANGE HOOD
MODEL
RG6WH RG6BL RG6SS RG6BR
RG9WH RG9BL RG9SS RG9BR
SERVICE MANUAL

RG - SERIES
APPROVED Page 2 of 9
ISSUE: F
ECN 07 033

RG - SERIES
APPROVED Page 3 of 9
ISSUE: F
ECN 07 033
ROBINHOOD GRANGE
RG6WH RG6BL RG6SS RG6BR GRANGE 600 – 2 SPEED
RG9WH RG9BL RG9SS RG9BR GRANGE 900 – 2 SPEED
ITEM DESCRIPTION PART No.
1 Power Cord 103424
2 Disfuser 101112
3 2 Spd. Motor & Sleeve Nuts 103673
4 Lamp 40W 101191
5 ‘E’ Clip E147 999084
6 Lamp Holder 101104
7 Screw Earth M5 x 8 Taptite 999083
8 Fan Blade ‘D’ Shaft 102283
9 Filter Spring (Polycarbonate) 101221
10 Filter (Aluminium) 600 x 2 Off
Filter (Charcoal) 600 x 2 Off
103793
103793C
Filter (Aluminium) 900 x 2 Off
Filter (Charcoal) 900 x 3Off
100046
103793C
11 Mounting Hardware (with Installations) 100651
12 Wire Tie 106099
13 Cord Entry Family Includes: 102549CL
2 Grommets
4 Top Mount Inserts
1 Cord Entry
2 Wire Covers
1 Cable Clamp
20 Closed End Connectors 102321
21 Washer External Lock M5 999085
Fingerguard 103943

RG - SERIES
APPROVED Page 4 of 9
ISSUE: F
ECN 07 033
ROBINHOOD GRANGE
RG6WH RG6BL RG6SS RG6BR GRANGE 600 – 2 SPEED
RG9WH RG9BL RG9SS RG9BR GRANGE 900 – 2 SPEED
ITEM DESCRIPTION P/N 600 P/N 900
Grange - White
14 Motor Housing 101052WH 101053WH
15 Rear Cover 101062WH 101063WH
16 Corners L&R 101150WH 101150WH
17 Exhaust Cover 101064WH 101065WH
18 Switch Lamp 100683
103892
100683
103892
19 Switch Fan 100684
103893
100684
103893
Grange – Nordic Brown
14 Motor Housing 101052NB 101053NB
15 Rear Cover 101062NB 101063NB
16 Corners L&R 101150BR 101150BR
17 Exhaust Cover 101064NB 101065NB
18 Switch Lamp 100685 100685
19 Switch Fan 100686 100686
Grange – Copper Spangle
14 Motor Housing 101052CS 101053CS
15 Rear Cover 101062CS 101063CS
16 Corners L&R 101150BR 101150BR
17 Exhaust Cover 101064CS 101065CS
18 Switch Lamp 100685 100685
19 Switch Fan 100686 100686
Grange – Black
14 Motor Housing 101052BL 101053BL
15 Rear Cover 101062BL 101063BL
16 Corners L&R 101150BL 101150BL
17 Exhaust Cover 101064BL 101065BL
18 Switch Lamp 100685 100685
19 Switch Fan 100686 100686

RG - SERIES
APPROVED Page 5 of 9
ISSUE: F
ECN 07 033
SECTION 1.
MOTOR REMOVAL AND REPLACEMENT
1.1 REMOVE DIFFUSER AND LIGHT BULB
1.2 REMOVE FINGERGUARD AND FANBLADE
1.3 REMOVE REAR COVER
1.4 REMOVE FILTER SPRINGS AND LOCATING SCREWS ON MOTOR
HOUSING
1.5 LIFT MOTOR HOUSING FRONT EDGE, DRAW POWER CABLE
THROUGH BACK
1.6 DISCONNECT SWITCHES
1.7 REMOVE MOTOR HOUSE FROM BODY AND TURN UPSIDE DOWN
ON TOP OF BODY
1.8 REMOVE MOTOR NUTS AND WASHERS
1.9 DRAW MOTOR DOWN, AWAY FROM MOUNTING BRACKET TO SHOW
MOTOR
1.10 CUT WIRES FROM NEW MOTOR KIT. LEAVE ABOUT 3 OR 4mm OF
COLOUR ON RED, BLACK AND WHITE WIRES (DO NOT UNSOLDER
THESE WIRES).
1.11 SOLDER WIRES FROM RANGEHOOD ONTO NEW MOTOR (USE
COLOURS TO MATCH WITH).
1.12 REMOUNT MOTOR TO BRACKET
1.13 REASSEMBLE RANGEHOOD IN REVERSE TO PROCEDURE ABOVE,
TAKING CARE TO PULL AS MUCH OF THE POWER CORD OUT OF
THE BODY AS POSSIBLE
1.14 TEST TO ELECTRICAL SAFETY STANDARDS

RG - SERIES
APPROVED Page 6 of 9
ISSUE: F
ECN 07 033
SECTION 2.
SWITCH REPLACEMENT
2.1 REMOVE MOTOR HOUSING AS PER THE INSTRUCTIONS IN
SECTION 1
2.2 SWITCHES ARE REMOVED FROM THE INSIDE OF THE RANGEHOOD
BY DEPRESSING THE HOLDING TAGS MOULDED INTO EACH SIDE
OF THE SWITCH
2.3 REPLACE WITH NEW SWITCH, CHECK WIRING AS PER WIRING
DIAGRAM, AND THAT SWITCHES ARE IN THE CORRECT POSITION
SECTION 3.
POWER CORD REPLACEMENT
3.1 REMOVE MOTOR HOUSING AS PER THE INSTRUCTIONS IN
SECTION 1
3.2 REMOVE CABLE CLAMP
3.3 PULL OUT POWER CORD AND REMOVE BY CUTTING OFF THE
CLOSED END CONNECTORS, STRIP AND RECONNECT NEW CORD
USING NEW CONNECTORS – CRIMP SECURELY
3.4 REPLACE CABLE CLAMP
3.5 CARRY OUT EARTH TEST BEFORE CONNECTING TO POWER

RG - SERIES
APPROVED Page 7 of 9
ISSUE: F
ECN 07 033

RG - SERIES
APPROVED Page 8 of 9
ISSUE: F
ECN 07 033
WIRING DIAGRAM FOR
100683 AND 101909 LIGHT SWITCH
100684 AND 101910 FAN SWITCH

RG - SERIES
APPROVED Page 9 of 9
ISSUE: F
ECN 07 033
WIRING DIAGRAM FOR
103892 AND 103894 LIGHT SWITCH
103893 AND 103895 FAN SWITCH