ROBINHOOD 6F6WH User manual

6F -SERIES
APPROVED Page 1 of 7
ISSUE: C
ECN2802
POWERPACK RANGE HOOD
MODEL
6F6WH, 6F8WH
SERVICE MANUAL

6F -SERIES
APPROVED Page 2 of 7
ISSUE: C
ECN2802

6F -SERIES
APPROVED Page 3 of 7
ISSUE: C
ECN2802
POWERPACK
ITEM DESCRIPTION 6F6WH 6F8WH
PART No. PART No.
1* Filter Fan Unit
2* Fan Box
3 Motor E.B.M.R2E220 102767
4 Power Cord 103821
5 Rotary Switch Assy. 102908
6 Switch 770 MEC 102909
7 PCB Heat Alarm 102746
8 Capacitor 102793
9 Resistor PW50 102690
10 Lamp Holder Assy. 102795
11 Lamp 40W 101191
12 Filter 102910 102385
13 Terminal Block 101841
14 Vent Plug 101716
15 Motor Bracket 102438
16 PCB Cover 102664
17 2 Gang Arch PLT 102907
18 Glass 102917 102918
19 Exhaust Cover 102790
20 Wire Tie 106099
21 Grommet 102384
22 Glass Ret. Bracket 103042
23 PCB Spacer 102747
24 Installation Instructions 102911
25 Fan Box Front Cover 102637WH
26 Bell Mouth E220 103194
*NOT AVAILABLE OUTSIDE PRODUCTION

6F -SERIES
APPROVED Page 4 of 7
ISSUE: C
ECN2802
POWERPACK
TO REPLACE MOTOR
1 DISCONNECT UNIT FROM POWER SUPPLY
2 REMOVE UNIT TO SUITABLE WORK AREA
3 REMOVE FILTERS
4 REMOVE GLASS DISFFUSERS BY UNDOING SCREWS AND
REMOVING RETAINERS, THEN SLIDE DIFFUSERS IN
TOWARD CENTRE OF UNIT TO CLEAR
5 REMOVE LAMPS
6 UNSCREW AND REMOVE LAMP HOLDER ASSEMBLYS
7 REMOVE 7 SMALL SCREWS TO RELEASE FAN BOX AND
LIFT IT SUFFICIENT TO CLEAR MOTOR MOUNTING
BRACKET
8 UNDO TWO NYLOC NUTS TO LIFT MOTOR BRACKET CLEAR
OF BODY
9 TAKE NOTE OF MOTOR WIRE COLOURS IN TERMINAL
BLOCK BEFORE REMOVING MOTOR WIRES
10 UNDO FOUR SCREWS TO REMOVE MOTOR FROM MOTOR
BRACKET
11 MOUNT NEW MOTOR AND REASSEMBLE UNIT IN REVERSE
OF ABOVE PROCEDURE
12 TEST TO APPROPRIATE ELECTRICAL STANDARDS BEFORE
USE

6F -SERIES
APPROVED Page 5 of 7
ISSUE: C
ECN2802
TO REPLACE POWER CORD
1 DISCONNECT FROM POWER SUPPLY
2 REMOVE UNIT TO SUITABLE WORK AREA
3 REMOVE FILTERS
4 REMOVE GLASS DISFFUSERS BY UNDOING SCREWS AND
REMOVING RETAINERS, THEN SLIDE DIFFUSERS IN
TOWARD CENTRE OF UNIT TO CLEAR
5 REMOVE LAMPS
6 UNSCREW AND REMOVE LAMP HOLDERS
7 REMOVE 7 SMALL SCREWS TO RELEASE FAN BOX AND
LIFT IT CLEAR OF BODY
8 DISCONNECT POWER CORD WIRES (TAKE NOTE OF
COLOUR POSITIONS) FROM TERMINAL BLOCK, DISPOSE OF
OLD POWER CORD
9 ASSEMBLE NEW POWER CORD AND REASSEMBLE UNIT IN
REVERSE OF ABOVE PROCEDURE
10 TEST TO APPROPRIATE ELECTRICAL STANDARD BEFORE
USE
TO CHANGE LAMP
1 DISCONNECT FROM POWER SUPPLY
2 REMOVE FILTER
3 REMOVE GLASS DISFUSSER BY UNDOING AND REMOVING
RETAINER. SLIDE DIFFUSER IN TOWARD CENTRE OF UNIT
TO CLEAR
4 CHANGE LAMP (NOTE 40W MAX)
5 REPLACE DIFFUSER AND FILTER IN REVERSE OF ABOVE
PROCEDURE

6F -SERIES
APPROVED Page 6 of 7
ISSUE: C
ECN2802