ROBINHOOD RHCI9SS - IMPRESA User manual

114370 Issue C
ECN 07 007
INSTALLATION INSTRUCTIONS CANOPY HOOD
Model No: RHCI9SS - IMPRESA
(PLEASE NOTE PRODUCT MAY VARY SLIGHTLY FROM THE PICTURE)
PRE-INSTALLATION
Thank you for purchasing a quality, stainless steel canopy hood.
We have a high standard of quality control and each canopy hood is tested and approved before it
leaves the factory.
IMPORTANT
•Please read the entire instructions before installing the canopy hood
•Always switch the power off prior to installation, servicing or cleaning the canopy hood.
•Never use the canopy hood without the filters.
•Stainless steel is very easily damaged during installation if abraded or knocked by tools.
•Note all ducting must comply with local requirements and building codes.
•A power outlet should be within 1200mm from the motor assembly and can be either on the
wall, behind the chimney or in the ceiling.
All electrical work must be done in accordance with local and/or national electrical
codes as applicable. For safety, this product must be earthed. If you are unfamiliar with
methods of installing electrical wiring, employ the services of a qualified electrician.
Turn off power at service entrance before installing wiring or servicing this product.
lbs
The canopy hood is heavy please ensure adequate care when installing the canopy
hood to prevent personal injury.
The canopy hood must be installed onto a solid wall or solid stud. (Weight = 15 Kg)

CONTENTS
Contents of packaging Equipment Required Optional Accessories
1 x Canopy hood Electric Drill Drill bits Charcoal Filter 2516
2 x Chimney pieces with bracket Screwdriver Spirit Level Light Bulb 114313
1 x Installation instructions Duct tape Tape measure Chimney Ext (10’) 2190
3 x Filter (Part Number 114371) Jig saw Knife Chimney Ext (12’) 2191
Installation kit (Part Number 114326) Ladder Saw
2 x 12 x 2’ Screw
4 x 15 Dia Washer
2 x Wall Anchor Plastic
2 x 8 x 1.25’ Screw
4 x M4 x 8 Pan Head Screw
HEIGHT OF CANOPYHOOD
C
FILTER SURFACE
HOB TOP
BA
A=600mm(electric cook top)
min
A=650mm(gas cook top) min
B=485mm
C=220
•The canopy hood is designed for 2400mm
ceilings.
•The chimney is telescopic and is designed for
hood installations between 600 to 750mm above
the cooking surface.
•Ascertain the desired installation height of the
canopy hood.
•Any installation above 750mm will compromise
the extraction performance.
•The air outlet from the motor requires 150mm
round ducting which requires 170mm diameter
hole in the ceiling.
CONTROL PANEL
Timer switch: Canopy hood will remain on a low,
mid or high speed for 15 minutes to clear away all
residual cooking odours before switching off
automatically.
Timer Speed settings Lights

WALL/CEILING PREPERATION
RECIRCULATION
For recirculation, do not cut 170mm hole and purchase a charcoal filter.
For other accessories, parts and service, please contact your local supplier or approved service agent
DUCTED
For ducted installation, it is recommended you use 150mm diameter rigid / semi rigid ducting this
will require a 170mm hole in the ceiling / wall.
Before drilling any holes check the area behind the surface to be drilled is clear of any electrical
cables, pipes etc.
NOTE: Fixing to a solid stud is recommended.
1. Pre drill pilot hole 3mm diameter at
dimensions C and B.
B=485mm and C=220
2. Loosely fix the mounting screw and 2 x
washer in position, check with a spirit level
across the washers to ensure they are level.
3. Mark the position of the decorative
chimney at the ceiling and wall. Cut the
cornice moulding away if required, to
enable the chimney to fit flush against the
wall and ceiling.
4. Mark and cut out the hole in the ceiling /
wall to fit the ducting. (170mm dia.) This is
positioned centrally above the canopy hood
and 85mm from the wall. (For ceiling
option)
5. Using the screws supplied, fix the chimney bracket to the wall, 100mm below the ceiling
checking that it is aligned with the hood.
6. Remove the protective plastic covering from all parts including the filters. Fit the canopy hood
on the mounting screws, tighten screws. Plug in the power cord to the supply and check the
function of the canopy hood. Connect and secure the ducting (use duct tape if required).
7. Assemble the top chimney to the chimney bracket and fix using the screws supplied, then
assemble the bottom chimney to the canopy hood and fix using the screws supplied.
8. Remove transport tape that holds the oil cup in place under the motor unit and fit the filters.
DIA 170
85 TO C
100
DIM B
DIM C
DIM A
SEE NOTE
L

MAINTENANCE
Particular care must be taken with the grease filters which must be periodically cleaned (at least
every two months). Remove the grease filters and wash them either by hand using hot soapy water
or in the dishwasher using mild detergent. Note- some discolouration of the frame may occur.
Caution: Never use abrasive or oil based liquid cleaners. To clean the stainless steel and glass
components of the appliance use mild detergent and warm water. In areas of high humidity and
coastal environments cleaning should be carried out frequently.
In the case of charcoal filters, these are disposable items and it is recommended that these be
replaced every 2-4 months depending on the use of the canopy hood.
For other accessories, parts and service, please contact your local supplier (Refer to the Warranty
Certificate).
LIGHT REPLACEMENT
(Halogen bulb 12 Volts/10 Watt)
1. Switch off the power to the canopy hood and allow the bulb to cool.
2. Use a small bladed screwdriver to prise off the light cover, taking care not to
damage the surrounding material.
3. Use a cloth to remove the bulb.
4. Replace with a new bulb using a cloth. Do not touch the bulb with fingers.
5. Snap the cover back in place.
WARNINGS
•This canopy hood is not intended for use by young children or infirm persons without
supervision.
•Young children should be supervised to ensure that they do not play with the canopy hood.
•There shall be adequate ventilation of the room when the canopy hood is used at the same time
as appliances burning gas or other fuels. (A partial vacuum in the room could result in too high a
concentration of gas in the air)
•You must read the details concerning the method and frequency of cleaning (see maintenance).
•There is a fire risk if cleaning is not carried out in accordance with the instructions.
•Do not flambé under the canopy hood.
•Exhaust air must not be discharged into an existing flue which is used for exhausting fumes
from appliances burning gas or other fuels
•The minimum distance between the hob surface and the filters of the canopy hood shall be
600mm (650mm if installed over a gas hob).
•Attention should be given to ensure that any applicable regulations concerning the discharge of
exhaust air is fulfilled.
•If the supply cord of this equipment is damaged it must only be replaced by the manufacturer, its
service agent or similarly qualified person in order to avoid a hazard.
ISO 9001/2000 certification
New Zealand: Robinhood Ltd
Tel: [phone] Fax: [phone]
Email: [e-mail]
www.robinhood.co.nz
Australia: Robinhood Australia Pty Ltd ACN
Tel: [phone] Fax: [phone]
Email: [e-mail]
www.robinhood.com.au
RECOMMENDED DUCTING
SYSTEM FOR RANGEHOODS