ROBINHOOD Slimline 600 User manual

WALL MOUNTING
103767 Issue A
ECN:2557
INSTALLATION INSTRUCTION
RANGEHOOD SIDE WALL MOUNTING
If using Uniduct
cut outside wall
hole
90 x 290mm
600-800mm
For Gas 650-800mm
2.4M
CEILING
HEIGHT
900mm
STOVE
HEIGHT
UNDERCUPBOARD MOUNTING
290
MODEL 900
817
523
MODEL 600
18
For rear
ducting cut hole
to suit duct size.
Dimensions
shown
are for Uniduct
104
732
to
932
900
STOVE
HEIGHT
Underside View of Cupboard
For top ducting cut hole
to suit duct size.
Dimensions shown are
for Uniduct
523 (600)
817 (900)
290
75
95
45
165
Drill
5mm
holes
Wall
SCREW
THROUGH
SIDES USING
HOLE POSITIONS
INDICATED REMOVE FILTERS
MOUNTING OPTIONS
MOUNTING UNDER
CUPBOARDS
MOUNTING TO REAR WALL
DRILL HOLES AND MOUNT TWO
CUP WASHERS AS SHOWN
REFER WALL MOUNTING DETAIL
IF UNIT COMES WITH
KNOCK-OUT - REMOVE
SWIVEL POWER OUTLET TO TOP
1
2
1
12HOOK RANGEHOOD ONTO CUP
WASHERS, FIX TOP BRACKET
(BRACKET IS PRE-FITTED ON
RANGEHOOD)
INNER CUPBOARD MOUNTED
DRILL FOUR HOLES AT
POSITIONS INDICATED,
REFER UNDER CUPBOARD
MOUNTING
SWIVEL POWER OUTLET TO TOP.
CUT HOLE IN CABINET TO SUIT SCREW INTO PLASTIC INSERTS
FROM INSIDE CUPBOARD
DOOR EXTENSION
CONCEALS TOP OF
RANGEHOOD
(SL Models Only)
295mm
SL Models Only
72mm
SL Models Only
WALL MOUNTING DETAILS
FOR INSTALLATION OF PLUGS
FOR WALL MOUNTING
1. Mark location of holes as per
installation instructions.
2. Drill 8mm hole.
Note: Do not use a screw driver
to punch a hole in the base
material.
3. Insert Plastic Toggle and tap
with a hammer to ensure it is
flush with the base material.
4. Place supplied screw through
cup washer. Insert into toggle
and tighten.
NOT FOR USE
IN SOLID WALLS
FOR SOLID WALLS
USE APPROPRIATE
WALL PLUGS
Note: Generic model is shown.
Actual product may differ.
250 (SL)
305
598 (600)
892 (900)
PLEASE READ THE ENTIRE INSTRUCTION BEFORE INSTALLING THE RANGEHOOD

103767 Issue A
ECN:2557
DUCTING OPTIONS
REAR DUCTED
RECIRCULATING
TOP DUCTED
THROUGH
ROOF
FLEXIBLE DUCT
FOR SIDE
DUCTING
NOTE: when ducting
Exhaust air must not be discharged into any chimney or flue which may carry combustion
products from other sources. In addition, exhaust air must not be discharged into a wall
cavity, unless designed for the purpose.
OPERATION & CLEANING
OPERATION
After your Rangehood is fixed in position:
1. Check that the light and the diffuser are in place.
2. See that the filters are correctly positioned.
3. If exhaust cover is supplied ensure it is fitted in a ducted mode.
Discard exhaust cover if a recirculating mode is being used.
Exhaust covers may be purchased from your rangehood supplier.
4. Plug into 230-240V outlet. Keep cord clear of stove elements or hot utensils.
Permanent wiring to house supply, or modifications to plug or wire should be
carried out by a registered electrician.
CLEANING
1. Disconnect the Rangehood from power supply.
2. Wash aluminium filters every 2 or 3 months, depending on usage, with hot
soapy water or in the dishwasher.
3. Charcoal filters are disposable items and should be replaced when cleaning
the rangehood.
4. Clean the external and internal surfaces including the fan blades, using a
damp cloth and mild detergent. Do not use any powder or abrasive cleaners.
REMOVE
EXHAUST COVER DO NOT REMOVE
EXHAUST COVER
DO NOT REMOVE EXHAUST COVER
DO NOT REMOVE
EXHAUST COVER
1. Disconnect the Rangehood from power supply.
2. Insert small screwdriver or slim knife as shown,
ease catch to side and slip out the diffuser.
3. Replace lamp (40 watt max).
4. Slide diffuser back into aperture and ‘click’ into
place.
LAMP REPLACEMENT
PARTS AND SERVICE
For Accessories, Parts or Services, please contact your local supplier
or approved service agent. (Refer to the Warranty Certificate)
WARNING
•This appliance is not intended for use by young children or
infirm persons without supervision.
•Young children should be supervised to ensure that they do
not play with the appliance.
•There shall be adequate ventilation of the room when the
rangehood is used at the same time as appliances burning gas
or other fuels.
•You must read the details concerning the method and frequency
of cleaning.
•There is a fire risk if cleaning is not carried out in accordance
with the instructions.
•Do not flambé under the rangehood.
•Exhaust air must not be discharged into an existing flue which
is used for exhausting fumes from appliances burning gas or
other fuels.
•The minimum distance between the hob surface and the lowest
part of the rangehood is 600mm. This distance shall be at
least 650mm, if the rangehood is installed over a gas hob.
(We recommend 700mm)
•Attention should be given to ensure that any applicable
regulations concerning the discharge of exhaust air is fulfilled.
•If the supply cord of this equipment is damaged, it must only
be replaced by the manufacturer or its service agent or similarly
qualified person in order to avoid a hazard.
Electrical Rating:
280W (1.16A)
Max. at 230-240V 50Hz
MANUFACTURED IN NEW ZEALAND BY:
ROBINSON INDUSTRIES LIMITED
P.O. BOX 51 201, PAKURANGA,AUCKLAND, N.Z.
TEL: [phone] • FAX: [phone]
ISO9001 Certified
RECOMMENDED UNIDUCT DUCTING
SYSTEMS FOR RANGEHOODS