ROBINHOOD Royale RR Series User manual

RR Series - ROYALE
APPROVED Page 1 of 8
ISSUE: F
ECN 3106
Royale
RETRACTABLE RANGE HOOD
RR6WH, RR6BL, RR6SS
RR9WH, RR9BL, RR9SS

RR Series - ROYALE
APPROVED Page 2 of 8
ISSUE: F
ECN 3106
RR6WH RR6BL RR6SS
RR9WH RR9BL RR9SS

RR Series - ROYALE
APPROVED Page 3 of 8
ISSUE: F
ECN 3106
ITEM DESCRIPTION RR6WH RR6BL RR6SS
1* FAN BOX
2* FAN BOX FRONT COVER
3CORD CLIP 106167 106167 106167
4POWER CORD 103821 103821 103821
5CAPACITOR 102793 102793 102793
6POWER RESISTOR 102690 102690 102690
7MOTOR/Fan Assy & Cap'r 102767 102767 102767
8MOTOR MOUNTING BRACKET 102438 102438 102438
9BELLMOUTH E220 103194 103194 103194
10 FRONT HANDLE 600 ASSY 103774WH 103774BL 103775SS
11 END CAP FAMILY 103778WH 103778BL 103778BL
12 SLIDER 102245 102245 102245
13 OUTER EXTRUSION 103104WH 103104BL 103104SS
14 SLIDER BRACKET-LEFT 103109WH 103109BL 103117SS
15 SLIDER BRACKET-RIGHT 103108WH 103108BL 103116SS
16 TRAY 103111WH 103111BL 103113SS
17 GLASS 102742 102742 102742
18* BODY WELDMENT
19 CONTROL PANEL ASSEMBLY 103131WH 103131BL 103133SS
20 LAMP HOLDER 101104 101104 101104
21 40W CANDLE GLOBE 102722 102722 102722
22 MICRO-SWITCH 102527 102527 102527
23 SLIDE SWITCH ASSEMBLY 103417WH 103417BL 103417BL
24 LIGHT DIFFUSER 103125 103125 103125
25 FILTER-'P' 102728 102728 102728
25 CHARCOAL FILTER x2 (600) 102925 102925 102925
26 FILTERTRAY 102660WH 102660BL 102662SS
27 FILM-EXHAUST COVER 102790 102790 102790
28 MICRO-SWITCH BRACKET 103114 103114 103114
29** Heat Alarm PCB 102746 102746 102746
NOTE: * parts are not available outside production.
**Not used in production for units date stamped post June 2003 production.

RR Series - ROYALE
APPROVED Page 4 of 8
ISSUE: F
ECN 3106
ITEM DESCRIPTION RR9WH RR9BL RR9SS
1* FAN BOX
2* FAN BOX FRONT COVER
3CORD CLIP 106167 106167 106167
4POWER CORD 103821 103821 103821
5CAPACITOR 102793 102793 102793
6POWER RESISTOR 102690 102690 102690
7MOTOR/Fan Assy & Cap'r 102767 102767 102767
8MOTOR MOUNTING BRACKET 102438 102438 102438
9BELLMOUTH E220 103194 103194 103194
10 FRONT HANDLE 900 ASSY 103776WH 103776BL 103777SS
11 END CAP FAMILY 103778WH 103778BL 103778BL
12 SLIDER 102245 102245 102245
13 OUTER EXTRUSION 103104WH 103104BL 103104SS
14 SLIDER BRACKET-LEFT 103109WH 103109BL 103117SS
15 SLIDER BRACKET-RIGHT 103108WH 103108BL 103116SS
16 TRAY 103111WH 103111BL 103113SS
17 GLASS 102742 102742 102742
18* BODY WELDMENT
19 CONTROL PANEL ASSEMBLY 103132WH 103132BL 103132SS
20 LAMP HOLDER 101104 101104 101104
21 40W CANDLE GLOBE 102722 102722 102722
22 MICRO-SWITCH 102527 102527 102527
23 SLIDE SWITCH ASSEMBLY 103417WH 103417WH 103417WH
24 LIGHT DIFFUSER 103125 103125 103125
25 FILTER-'Q' 102743 102743 102743
25 CHARCOAL FILTER x3 (900) 102926 102926 102926
26 FILTERTRAY 102661WH 102661BL 102663SS
27 FILM-EXHAUST COVER 102790 102790 102790
28 MICRO-SWITCH BRACKET 103114 103114 103114
29** Heat Alarm PCB 102746 102746 102746
NOTE: * parts are not available outside production.
**Not used in production for units date stamped post June 2003 production.

RR Series - ROYALE
APPROVED Page 5 of 8
ISSUE: F
ECN 3106
'Robinhood' Retractable Rangehood
WARNING: DISCONNECT POWER SUPPLY BEFORE SERVICING.
A) TO REPLACE MOTOR:
1PULL CANOPY OPEN. REMOVE FILTERS AND WORKING FROM
UNDERSIDE UNFASTEN 3 ‘a’ SCREWS. SEE DIAGRAM BELOW.
2UNFASTEN 5 SCREWS TO REMOVE THE FAN BOX FRONT
COVER FROM THE FAN BOX.
3UNFASTEN 2 ‘b’ SCREWS/NUTS TO REMOVE THE MOTOR
ASSEMBLY.
4CUT CABLE TIES AND DISCONNECT WIRES ATTACHED TO THE
TERMINAL BLOCK ON TOP OF THE MOTOR MOUNTING
BRACKET.
5REMOVE MOTOR ASSEMBLY FROM RANGEHOOD THROUGH
FAN BOX FRONT OPENING.
6REMOVE AND REPLACE MOTOR AND CAPACITOR FROM THE
MOTOR MOUNTING BRACKET.
7REFER TO THE WIRING DIAGRAM FOR WIRING DETAILS.
8RE-ASSEMBLE RANGEHOOD IN REVERSE TO PROCEDURE
ABOVE, USING CABLE TIES ON WIRES TO ENSURE THEY WILL
NOT COME INTO CONTACT WITH THE MOTOR.
UNDERSIDE VIEW OF RANGEHOOD

RR Series - ROYALE
APPROVED Page 6 of 8
ISSUE: F
ECN 3106
ROBINHOOD
B) TO REPLACE SWITCHES:
1PULL CANOPY OPEN, REMOVE FILTERS AND UNFASTEN
SCREWS FIXING CONTROL PANEL TO BODY.SEE DIAGRAM
BELOW.
2DROP CONTROL PANEL SLIGHTLY AND PULL FORWARD TO
DISENGAGE THE REAR TABS FROM THE BODY.
3LIGHT & FAN SWITCH AND MICRO-SWITCH ARE LOCATED
INSIDE THE CONTROL PANEL.
4REFER TO WIRING DIAGRAM FOR WIRING DETAILS.
5REASSEMBLE RANGEHOOD IN REVERSE TO PROCEDURE
ABOVE, USING CABLE TIES ON WIRES WHERE NECESSARY.
B) TO REPLACE HEAT ALARM: (Not applicable for units manufactured post June 2003 production.
1PULL CANOPY OPEN, REMOVE FILTERS AND FAN BOX FRONT
COVER AS DESCRIBED IN SECTION A.
2REMOVE HEAT ALARM COVER BY UNFASTENING THE
MOUNTING SCREW.
3SQUEESE THE LOCKING BARBS OF THE PCB SUPPORT
THROUGH THE MOUNTING HOLES TO RELEASE THE HEAR
ALARM
4REFER TO WIRING DIAGRAM FOR WIRING DETAILS.
5REASSEMBLE RANGEHOOD IN REVERSE TO PROCEDURE
ABOVE, USING CABLE TIES ON WIRES WHERE NECESSARY.
6TEST OPERATIONS OF HEAT ALARM - REFER TO HEAT ALARM
OPERATING INSTRUCTION.

RR Series - ROYALE
APPROVED Page 7 of 8
ISSUE: F
ECN 3106

RR Series - ROYALE
APPROVED Page 8 of 8
ISSUE: F
ECN 3106