ROBOfiber 8INJ-GE-125R User manual

4 www.robofiber.com
8INJ-GE-125RGigabit Power-over-Ethernet
Injector
Technical Specifications
No. of Channels
8
Pass Through Data Rates
10/100/1000 Mbps half/full duplex
Power over Ethernet
Output
Pin Assignment and Polarity: Both 1/2 (-), 3/6
(+)
Output Power Voltage
50V DC
Output Power: up to 125W total (15.4W
under 802.3af per port)
Input Power Requirements
AC 100-240V input, 0.5A
AC frequency: 50-60Hz
Connectors
Shielded RJ-45, EIA 568A and 568B
Safety
overload, overcurrent and overvoltage
protection, EMI protection
Dimensions
185mm x 341mm x 44mm
Mounting
1RU, 19” rack mountable
Environmental Conditions
Operating Ambient Temperature: -10 to 40℃
Operating Humidity: Maximum 85%, Non-
condensing
Storage Temperature: -30 to 70℃
Storage Humidity: Maximum 95%, Non-
condensing
Indoor rated operating device
PoE compliance
IEEE 802.3af (PoE), IEEE 802.3at (PoE+)
8 channels Gigabit PoE
Injector (15W/port)
802.3af compatible
8INJ-GE-125R
User Manual

2 3
8INJ-GE-125RGigabit Power-over-Ethernet
Injector
8INJ-GE-125RGigabit Power-over-Ethernet
Injector
High Power Gigabit Power-over-Ethernet Injector
Order Information
8INJ-GE-125R Gigabit PoE Injector 8(Data IN) and 8(Data/PoE OUT)
125W total power
Description
The 8INJ-GE-125R PoE Injector is an eight port mid-span PoE injector that
offers a cost effective, fully IEEE 802.3af compliant solution for remote
powering of wireless LAN (WAN) access points, IP Security cameras, VoIP
telephone and other PoE PD equipment.
The 8INJ-GE-125R injector supports 802.3af standard, delivering a maximum of
125W of power. It has a 3 pin IEC C14 plug for AC main input (90-240V) and
comes with a standard C13 power cord in the package.
Features
•Up to 15.4W of PoE Power delivered on 2-pairs on each port
•Supports 10/100/1000 Base-T applications
•LED indicators for AC power input and PoE power output
•Internal AC/DC built-in converter for compact design
•Easy plug-and-play installation
•Multi-protection following the IEEE 802.3af standards
•Gigabit full-rate network throughput
•19” Rack-Mountable design (1RU)
PWR: Power LED - a steady green light indicates that the PoE injector
receives 100-240V AC power input
PoE-in-use (each port): PoE LED - a steady yellow light indicates that the PoE
Injector delivers power to PD
Application Diagram
switch monitor
8INJ-GE-125R DVR
PoE cameras
The 8INJ-GE-125R PoE Injector is used with various PD (powered devices)
providing power in remote locations where no power lines or outlets are
available. Examples of PD PoE powered devices are WiFi APs, IP Cameras, IP
Phones, etc.
Installation steps:
1. Connect a Cat5e UTP cable from switch or data port to a DataIN port on
the 8INJ-GE-125R injector
2. Connect a Cat5e UTP cable from corresponding port on 8INJ-GE-125R
injector to final PD equipment (IP camera, etc.)
3. Connect AC power cord to AC mains.