ROBOfiber INJ-GE-30R User manual

4 www.robofiber.com
INJ-GE-30R Gigabit Power-over-Ethernet Injector
Technical Specifications
No. of Channels
1
Pass Through Data Rates
10/100/1000 Mbps half/full duplex
Power over Ethernet
Output
Pin Assignment and Polarity: Both 1/2 (-), 3/6
(+) and 7/8 (-), 4/5 (+)
Output Power Voltage
50V DC
Output Power: up to 30W (15.4W under
802.3af)
Input Power Requirements
AC 100-240V input, 0.5A
AC frequency: 50-60Hz
Connectors
Shielded RJ-45, EIA 568A and 568B
Network Cable Type
Outdoor type Shielded category 5 (or higher)
Dimensions
145mm x 60mm x 40mm
Mounting
Wall or shelf
Environmental Conditions
Operating Ambient Temperature: -10 to 40℃
Operating Humidity: Maximum 85%, Non-
condensing
Storage Temperature: -30 to 70℃
Storage Humidity: Maximum 95%, Non-
condensing
Indoor rated operating device
PoE compliance
IEEE 802.3af (PoE), IEEE 802.3at (PoE+)
Gigabit PoE Injector
802.3af/802.3at compatible
INJ-GE-30R
User Manual

2 3
INJ-GE-30R Gigabit Power-over-Ethernet Injector
INJ-GE-30R Gigabit Power-over-Ethernet Injector
Gigabit Power-over-Ethernet Injector
Order Information
INJ-GE-30R Gigabit PoE Injector 1(Data IN) and 1(Data/PoE OUT) 30W
Description
The INJ-GE-30R PoE Injector is a single port mid-span PoE injector that offers
a compact and cost effective, fully IEEE 802.3at/af compliant solution for
remote powering of wireless LAN (WAN) access points, IP Security cameras,
VoIP telephone and other low port density installations.
The INJ-GE-30R injector supports both 802.3af and 802.3at PoE standards,
delivering a maximum of 30W of power. It has a 3 pin IEC C14 plug for AC main
input (90-240V) and comes with a standard C13 power cord in the package.
Features
•Up to 15/30W of PoE Power delivered on 2-pairs
•Supports 10/100/1000 Base-T applications
•LED indicators for AC power input and PoE power output
•Internal AC/DC built-in converter for compact design
•Easy plug-and-play installation
•Multi-protection following the IEEE 802.3at/af standards
•Gigabit full-rate network throughput
•Wall-Mountable design (2 wall screw cross holes)
•Stack on rail for mounting multiple injectors in a single compact block
AC input Data IN PoE/Data OUT
PWR: Power LED - a steady green light indicates that the PoE injector
receives 100-240V AC power input
PoE: PoE LED - a steady green light indicates that the PoE Injector delivers
power to PD
Application Diagram
switch monitor
4 x INJ-GE-30R
PoE cameras
DVR
The INJ-GE-30R PoE Injector is used with various PD (powered devices)
providing power in remote locations where no power lines or outlets are
available. Examples of PD PoE powered devices are WiFi APs, IP Cameras, IP
Phones, etc.
Installation steps:
1. Connect a Cat5e UTP cable from switch or data port to DataIN port on
the INJ-GE-30R injector
2. Connect a Cat5e UTP cable from injector to final PD equipment (IP
camera, etc.)
3. Connect AC power cord to AC mains.