Roborock S6 MaxV User manual

4
Roborock S6 MaxV Robot Vacuum
Cleaner User Manual
Before using the product, read this manual thoroughly and save it for future reference.

5
Safety Information 6
Table of Faults 10
Product Overview 11
Installation 17
Instructions for use 23
Routine maintenance 27
Basic parameters 33
Troubleshooting 34
FAQs 36
EU Declaration of Conformity 38
WEEE Information 41
Warranty Information 42
•
•
•
•
•
•
•
•
•
•
•
•

6
• This product is designed for indoor floor cleaning only, do not use it outdoors
(such as on an open-ended terrace), on any surface other than the ground (such
as a sofa), or in any commercial or industrial environment.
• Do not use this product on elevated surfaces without barriers such as the floor of
a loft, an open-ended terrace, or on top of furniture.
• Do not use the product when the ambient temperature is higher than 104°F
(40°C), lower than 39°F (4°C), or if there are liquids or tacky substances on the
floor.
• Before using the product, move wires off the ground or place them to the side to
prevent them being pulled on by the cleaner.
• To prevent blocking the product and to avoid damage to valuables, remove
lighweight items (such as plastic bags) and fragile objects (such as vases) from the
floor before cleaning.
• Children should be supervised to ensure that they do not play with the appliance.
• This product is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
product by a person responsible for their safety (CB).
• This product can be used by children aged from 8 years and above and persons
Safety Information
Restrictions

7
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the product in a safe way and understand the hazards involved. Children shall not
play with the product. Cleaning and user maintenance shall not be made by
children without supervision (EU).
• Keep the main brush cleaning tools out of reach of children.
• Do not place any object (including children and pets) on the product, whether it is
in operation or not.
• Keep hair, loose clothing, fingers, and all parts of the body away from openings
and moving parts.
• Do not use the product on burning objects (such as cigarette butts).
• Do not use the product on high pile carpets (product effectiveness may also be
reduced on dark carpets).
• Do not use the product to clean hard or sharp objects (such as decoration wastes,
glass and nails).
• Do not carry the product using the laser scanner cap, main unit cover, or collision
buffer.
• The product must be switched off and the plug must be removed from
socket-outlet before cleaning or maintaining the product.
Safety Information

8
• Do not use wet cloth or liquids for cleaning the product.
• Do not use the mopping module on carpets.
• Use the product according to the manual. Any loss or damage caused from
improper use will be borne by the user.
• This product contains batteries that are only replaceable by skilled persons.
Safety Information
• Do not charge non-rechargeable batteries.
• For the purposes of recharging the battery, only use the detachable supply unit
roborock CDZ11RR or CDZ12RR provided with this product.
• Do not dismantle, repair or modify the battery or charging dock.
• Keep the charging dock away from heat (such as heating vents).
• Do not wipe or clean the charger prongs with wet cloth or wet hands.
• If the power cord is damaged, stop using it immediately. It must be replaced by
the manufacturer, its service agent, or similarly qualified persons to avoid a
hazard.
• Make sure the product is powered off before shipment.
• Use of the original packaging is advised.
Battery and Charging
WARNING

9
Safety Information
• If to be left unused for a long period of time, fully charge the product and switch it
off before storing it in a cool, dry place.
• Charge it at least every three months to avoid over discharging the battery.
• To satisfy RF exposure requirements, a separation distance of 20 cm or more
should be maintained between this device and persons during device operation.
• To ensure compliance, operations at closer than this distance is not
recommended.
• The antenna used for this transmitter must not be co-located in conjunction with
any other antenna or transmitter.

10
Item
Main Unit
Charging dock Main unit does not charge.
Main brush, side brush, fan or main wheel issue.
Does not power on.
Functions do not work.
Power cable Charging dock has no power.
Fault
Table of Faults
Table of Faults
WIFI Specification
Service
WIFI
Protocol
802.11b/g/n
Frequency Range
2400-2483.5 MHz
Max. Output Power
≤

11
Product Overview
Robot
Cover Grip
Clean/Power


Press to start cleaning

Power indicator




White: Battery level  20%.
Red: Battery level < 20%
Flashing slowly: Charging or starting up
Flashing red: Error
Reset WiFi
Press and hold both Spot Clean and Dock for 3
seconds
Spot Clean
Press to start spot cleaning
Dock
Press to return to Dock
Note:
Press any button to stop the robot during cleaning, returning to the
Dock, or spot cleaning

12
Product Overview
Dustbin Robot
Dustbin lid
Dustbin latch
Filter
System Reset
Air Vent
Water Tank Latch
Speaker
WiFi indicator





Flashing slowly: Waiting for
connection
Flashing quickly:
Connecting
Steady: WiFi connected

13
Product Overview
Accessories
Charging Dock
Mop Cloth Bracket
Moisture-proof Mat
Mop Cloth
Power Cable

14
Product Overview
Robot and Sensors
Infrared Fill Light
ReactiveAI Cameras
Dock Locator
Bumper
LiDAR Sensor
Wall Sensor

Omni-
Directional
Wheel
Charging
Contact
Side Brush
Main Wheel
Main Brush
Water Tank
Main Brush
Cover Latch
Vertical
Bumper

15
Product Overview
Mopping Module
Water Tank Stopper
Water Filter
Water Tank
Water Tank Latch
Mop Cloth Slot
Mop Cloth
Attachment Zone
Mop Cloth Bracket Latch
Mop Cloth Bracket

16
Charging Dock
Dock Location Beacon
Charging Dock Power Indicator
Charging Contacts
Product Overview

17
Installation
Important Information
Tidy cables and loose items from the ground and move any unstable,
fragile, precious, or dangerous items to prevent personal injury or
property damage due to items becoming tangled in, struck by, or
knocked over by the robot.
1. If using this robot in a raised area, always use a secure physical barrier
to prevent accidental falls that may result in personal injury or property
damage.
2.
Note:


18
Using the Robot
> 0.5m
> 0.5m
> 1.5m
Place the charging dock
Secure the charging dock with the adhesive tape.
1.
2.

the power cable to the Charging Dock and place any exposed cable
into the cable slot. To ensure a better user experience of the mobile
app, place the Charging Dock in an area with good WiFi coverage.


the dock onto the double-sided tape to secure it in place.
Double-sided tape
Note:
Note:
Allow at least 0.5m (1.6ft) of clearance on each side, and more than 1.5m (4.9ft) in front of the
Charging Dock.
If the power cable hangs vertical to the ground, it may be caught by the robot, causing the Charging
Dock to be disconnected.

charging.
Do not place the Charging Dock in places that are directly exposed to sunlight, and do not block the
Location Beacon. Otherwise the robot may not be able to automatically return to the Charging Dock.
Use double-sided tape to stick the Charging Dock down.
Use of the double-sided tape to secure the charging dock is optional.
When necessary, remove the double-sided adhesive tape slowly to reduce residue glue.







Installation

19
Attach the Moisture-Proof Mat3.


of the double-sided tape attached to the bottom of the Moisture-Proof
Mat, and stick the mat to the ground as shown.
Note:
The robot may not be turned on when the battery is low. In this case, connect the robot to the
Charging Dock.
Powering On and Charging4.
Press and hold the button to power on the robot. Wait until the
power light is steady, and then place the robot on the Charging Dock to
charge. The robot is equipped with a built-in high performance lithium-
ion rechargeable battery pack. To maintain battery performance, keep
the robot charged during normal use.
The color of the power
indicator indicates the
battery level.


White:  20%;
Red: < 20%
Note:

Peel the double-sided tape slowly to minimize residual adhesive.
The Moisture-Proof mat attaches better to smooth surfaces.



Installation

20
Installation
Connect to the app
Download the mobile phone app for more smart features.
(Optional)
5.
The robot supports the Roborock or Xiaomi home app. Choose the one
that best meets your needs.
Reset WiFi

Press and hold the and buttons until you hear the
"Resetting WiFi" voice alert. Reset is complete when the WiFi


Download the app
Search for "Roborock" in the App Store or Google Play or scan
the QR code to download and install the app.

a.
a.
b.
Add device

On the homepage of the app, tap "+" in the top right corner and add
the device according to the in-app guide. After a device has been
added, it can be found from the list on the home screen.
Search for "Xiaomi home" in the App Store or Google Play or scan
the QR code to download and install the app.
b.
Note:
If the mobile phone fails to connect to the robot, reset the robot WiFi and add it again when it is
waiting for a connection.
Note:
The actual process may vary due to ongoing app updates. Follow instructions provided in-app.
Only 2.4GHz WiFi is supported.


WiFi indicator





Flashing slowly: Waiting for
connection
Flashing quickly:
Connecting
Steady: WiFi connected

21
Installation
Using the Robot
Remove the water tank
Reinstall the water tank
Fill the water tank
Install the mop cloth




Press the water tank latch and slide the tank backwards.
Slide the water tank into the robot until you hear it lock with a click.

Dampen the mop cloth and wring it until it stops dripping. Insert it into

Note:

Note:

Do not use hot water as this may cause the tank to deform.
6.
Note:





22
Installation
Using the Robot
Install the Mop Cloth Bracket

Slide the bracket along the back of the water tank. A click indicates that
it is locked in place.
Note:

quality.

Start cleaning.
Remove the Mop Cloth Bracket
Remove the Mop Cloth Bracket from the water tank
7.
8.
9.
10.

Charging is complete when the power indicator light changes from
breathing to a steady white light. Press the button or use the app
to start cleaning.
When the robot returns to the Charging Dock after cleaning, press the
latches on both sides, and slide the Mop Cloth Bracket backwards to
remove it.
Press the two side latches inwards and slide the Mop Cloth Bracket
backwards as shown to remove it from the water tank.
Low
WaterLevel
Medium
Water Level
High
Water Level
Note:
After mopping, remove the Mop Cloth Bracket, pour out residual water from the water tank, and
clean the mop cloth to avoid mold and odor.
Remove the Mop Cloth Bracket when not mopping.



23
Instructions for use

Start Cleaning
Press and hold the button to power on the robot. The power indicator
will turn on and the robot will enter standby mode. When the robot is

cleaning cycle.
Press the button to start cleaning. The robot will plan its cleaning



Note:

Zone 1 has
been cleaned.
Zone 4 is
pending.
Zone 2 has
been cleaned.
Zone 3 is
being cleaned.
Note:
Cleaning cannot start if the battery level is too low. Allow the robot to charge before restarting cleanup.

may be dragged by the robot, resulting in the disconnection of electrical appliances or damage of cables
and property.
If cleaning is completed in less than 10 minutes, the area will be cleaned twice.
If the battery runs low during the cleaning cycle, the robot automatically returns to the Charging Dock.





Sleep
If the robot is paused for over 10 minutes, it will go to sleep, and the

robot up.
Note:
The robot will not go to sleep when it is on the Charging Dock.
The robot will automatically shut down if left in sleep mode for more than 12 hours.


Pause
When the robot is running, press any button to pause it.
Then press the button to continue cleaning or the button to
return it to the Charging Dock and stop the cleaning cycle.
Note:
Placing a paused robot on the Charging Dock manually will end the current cleanup.