Roborock S6 Pure User manual

Roborock Vacuum
Cleaner S6 Pure

https://drive.google.com/open?id=1zuui9MLG63FB5Qb8tWaNvyjKS_GZg7h
9
Part1 App Connection

Part2 App Features
Instruction
Before the first cleaning task, please go to Settings page and turn on
the map saving mode. During cleaning, please ensure that the
cleaner starts from the dock charger. The cleaner will automatically
return to dock charger after all the rooms have been cleaned.
The charging dock needs to be placed against the wall. Obstacles are not
allowed within 0.5m to the left and right of the cleaner, and within 1m in front of
the charging dock.

1.Room cleaning
The cleaner will automatically
divide areas based on rooms. When
you don't want to clean all rooms
but just one or multiple rooms, go
to the map interface, as shown
below, and tap to select the
room(s) you want to clean.
At the same time, you can
customize the clean mode

2. Zone cleaning
Only a simple one-step operation on
the app is required to make the
cleaner automatically clean the target
area.
Method: Go to the map interface and
tap the Zone button. The initial areas
will automatically pop up on the map.
You can manually move or scale up or
scale down the target cleaning area.
At the same time, you can customize
the ①numbers of cleaning, ②cleaning
mode

The complexity of the home
environment may cause some
errors in the automatic area
division by the machine. The
manual area division function
allows us to correct the errors
according to the actual home
environment.
Method: Enter the map interface
for the cleaner and tap ①“Edit
map”, then go to “②Edit room".
If you want to merge two areas, tap
“Merge". If you want to divide an
area, tap “Divide", and then
proceed by following the
instructions.
3. Edit room

Method：Enter the map interface, go to“Mode settings”to choose the cleaning mode.
4. Custom cleaning mode

Method: Enter the map interface for the cleaner and tap Edit map”-“No-go zone”,Then
tap the Invisible wall”\“No-go zone”,buttons to scale up/scale down/move invisible walls
and no-go zones. Tap “①”save and the cleaner will not enter these zones.
注意:
1. You can add up to 10 invisible walls and no-go
zones respectively when the cleaner is online.
The cleaner will pause cleaning when you add an
invisible wall or no-go zone.
2. You can edit or delete a no-go zone or
invisible wall only when the cleaner is charging,
but not in any other states.
3. The min. area for a no-go zone is 0.2m² and
the max. area is 10m*10m while the min. length
for an invisible wall is 0.4m and the max. length
is 10m.
4. A no-go zone or invisible wall should be at
least 50 cm away from the dock.
5. Invisible wall and no-go zone

6.Carpet mode
When this mode is enabled, the
cleaner will automatically identify a
carpet during cleaning and apply
the maximum suction power to
clean it, and resume its normal
suction power when stepping off
the carpet.
Method: enter ①Setting-②Vacuum
settings, Enable ③"Carpet mode"
button.

7.DND mode
Note:
1.After the DND mode is enabled, if the cleaner
automatically return to charging dock due to low
battery capacity, the machine will not continue
cleaning after the battery capacity is sufficient.
2. All passive voice prompts (such as low battery)
will be unavailable and the brightness of the power
light will reduce.
3.The DND mode will be disabled once there is any
active operation (such as removing the dust bin).
This mode is enabled in the factory and effective
between 22:00-08:00 by default.
After scheduled cleaning is set up, the
machine will perform this action before it is
connected to Wi-Fi（TW、RUS
regardless of whether it is connected to
Wi-Fi ）.