Roborock Auto-Empty Dock AED01HRR User manual

Read this user manual carefully before using this product and store it
properly for future reference.
Roborock Auto-Empty Dock
User Manual

1 English
33 Français
68 Deutsch
103 Italiano
137 Español

1 Safety Information
5 Accessories
6 Product Introduction
10 Getting Started
15 Routine Maintenance
26 Basic Parameters
27 FAQs & Troubleshooting
29 EU Declaration of Conformity
31 WEEE Information
32 Warranty Information
Contents

1
Safety Information
Restrictions
•This product is designed for indoor use only, do not use it outdoors (such as on
an open-ended terrace), on any surface other than the ground (such as a sofa),
or in any commercial or industrial environment.
•The product must be switched o and the plug must be removed from socket
outlet before cleaning or maintaining the product.
•Do not place any object near the suction inlet of the dock.
•Do not put ngers into the seam of the dock to avoid possible injury.
•Do not operate the product in a room where an infant or child is sleeping.
•Do not carry the product using the dustbin handle or lter cover.
•Make sure the robot is compatible with the dock, otherwise emptying or charg-
ing may fail.
•Do not use the product to clean hard or sharp objects (such as decoration
wastes, glass and nails).
•This product is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
English

2
product by a person responsible for their safety (CB).
•This product can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the product in a safe way and understand the hazards involved. Children shall
not play with the product. Cleaning and user maintenance shall not be made by
children without supervision (EU).
•Children should be supervised to ensure that they do not play with the appliance.
•Do not use the dock to pick up stones, paper scraps, or other objects that may
block the air duct. If the air duct gets blocked, clean it immediately.
•Do not use the product when the ambient temperature is higher than 40°C
(104°F), lower than 4°C (39°F).
•Place the dock on a at oor away from re, heat, and water. Avoid narrow spac-
es or locations where the robot may be suspended in air.
•Do not place any object (including children and pets) on the dock or cover it with
any item (including dust-proof cover), whether it is in operation or not.
•Do not pick up anything that is burning or smoking, such as cigarettes, matches,
or hot ashes.
Safety Information

3
•Do not use the dock to pick up ammable or explosive objects such as re light-
er, gasoline, and toner used in printers or copiers.
•Use the product according to the manual. Any loss or damage caused from im-
proper use will be borne by the user.
•Do not charge non-rechargeable batteries.
•In order to avoid a hazard due to inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through an external switching device, such
as a timer, or connected to a circuit that is regularly switched on and o by the
utility.
•Be sure that the supply voltage meets the requirements listed on the dock.
•Only use the power cable provided with the product to prevent potential smoke,
heat or re.
Battery and Charging
WARNING
Safety Information

4
•Do not use the product with any type of power adapter, as this may cause dan-
ger and void the warranty.
•Do not dismantle, repair or modify the battery or charging dock.
•Do not wipe the charging contacts with wet cloth or wet hands.
•If the power cord is damaged, stop using it immediately. It must be replaced
by the manufacturer, its service agent, or similarly qualied persons to avoid a
hazard.
•If the dock is placed in an area susceptible to thunderstorms or with unstable
voltage, take protection measures.
•Use of the original packaging for transportation is advised.
•Unplug the power cable before placing the dock into storage.
Safety Information

5
Accessories
Dock Base Power Cable Screwdriver
MAX
Auto-Empty Dustbin Dust Bag Holder Disposable Dust Bag

6
MAX
Auto-Empty Dock
Product Introduction
Status Indicator Light
•Steady white: Standby.
•Flashing white : Emptying.
•Steady red: Malfunction.
•Light o: Charging, not powered on, or
malfunction for more than 10 minutes.
Charging Contacts
Dock Location Beacon
Electrode Brushes
Suction Inlet
Dock
Base

7
Auto-Empty Dock Base
Product Introduction
Filter Cover
Front Filter
Rear HEPA Filter
Air Duct Cover
Screwdriver
Air Duct Cover
Screws (7)
Base Fastening
Screws (5)
MAX

8
Power cable can be pulled out at both sides.
Dustbin Power Cable Storage
Product Introduction
MAX
Dustbin Handle
Air Outlet
Dustbin Opener
Dustbin Opening
Cyclone Separator
Note:
Cable Outlet
Power Cable
Storage Slot
Power Port

9
Auto-Empty Dustbin
Product Introduction
Filter Cover
Filter Cover Latch
Air Inlet
Washable Filter

10
Getting Started
Assembly
1. Take the screwdriver from its storage bin at the bottom of the
base.
2. Place dock upside down on a soft, at surface (carpet/towel/
cloth) and attach the base by screwing in ve screws in the
areas marked with a , as shown.

11
MAX
Getting Started
4. Place the dock on a hard and at oor (wood/tile/concrete etc.).
Keep at least 0.5 m (1.6 ft) of clearance on either side, 1.5 m (5 ft)
in front, and 1 m (3 ft) above. Check the location has good WiFi
then turn on.
Notes:
•The status indicator light turns o automatically when the robot is charging.
•The status indicator turns red if an error occurs, and turns o automatically after 10
minutes.
•Do not use without lter, dustbin, cyclone separator, or dust bag. They are already installed
during production. For details on assembly and cleaning, please refer to the "Routine
Maintenance" section in this manual.
•Place the dock on a at oor away from re, heat, and water. Avoid narrow spaces or
locations where the robot may be suspended in the air.
•Placing the dock on a soft surface (carpet/mat) may cause the dock to tilt over and cause
problems docking and departing.
•Keep excess power cable inside the storage slot so that the robot will not get tangled in the
cables, and the dock will not be dragged away or disconnect from the power supply.
•Keep the dock away from direct sunlight or anything that may block the dock location
beacon; otherwise, the robot may fail to return to the dock.
•The Auto-Empty Dock recharges and empties. Store the standard robot dock before use.
Failure to do so may cause issues returning to dock.
•Maintain the dock according to the maintenance instructions. Do not clean the dock with a
wet cloth.
3. Connect the power cable to the dock, and keep excess cable
inside the storage slot.
≥0.5 m
(1.6 ft) ≥0.5 m
(1.6 ft)
≥1.5 m
(5ft)
≥1 m (3 ft)

12
Avoid frequent manual emptying.
Make sure the dustbin provided with the robot has been replaced with the auto-
empty dustbin or it may fail to empty automatically.
Getting Started
Robot Dustbin Replacement
1. Only replace with the Auto-Empty Dustbin
1. Remove the original robot dustbin.
2. Remove the plate covering the air inlet in the robot.
3. Put in the auto-empty dustbin
Note:
3. Manual Emptying
Manual emptying can be performed by pressing the DOCK
button when the robot is being charged on the dock.
4. Stop Emptying
Press any button on the robot to stop emptying.
Note:
2. Auto Emptying
Auto emptying will begin when the robot returns to the auto-
empty dock after cleaning.
MAX

13
The disposable dust bag uses a one-time seal design to eectively prevent
dust from spreading outward during replacement. If you do not want to discard the
dust bag, do not pull out the seal. If the seal is pulled out, it cannot be restored to the
original state, which will aect the use of the dust bag.
Note:
Getting Started
Using the Disposable Dust Bag
1. Remove the dustbin vertically as indicated by the arrow.
2. Press the Dustbin Opener to open the bottom lid of the dust-
bin. Rotate the cyclone separator as shown to remove it.
MAX

14
Getting Started
3. Rotate the dust bag holder as shown to install it until you hear
it click in place.
4. Install the disposable dust bag in place along the slot.
5. Close the dustbin and place it back in the dock.
MAX

15
Notes:
•To ensure optimal performance, clean the dustbin regularly or when the dust reaches the
MAX mark.
•After using the cyclone separator, there may be a small amount of debris such as hair or
dust left in the dustbin. This is normal and will not aect performance.
Routine Maintenance
1. Remove the dustbin vertically as shown.
2. Hold the dustbin approx. 15 cm (6 in) over a bin then press the
Dustbin Opener.
3. After emptying, close the bottom lid and reinstall the dustbin on
the dock.
Dustbin Emptying
1* Clean on a monthly basis
MAX
MAX

16
Routine Maintenance
1. Empty the dustbin and remove the cyclone separator.
Dustbin & Cyclone Separator Cleaning
2
Notes:
•To avoid potential corrosion, do not use detergents, polishes or air fresheners to clean
the dustbin or cyclone separator.
•Do not wash the dustbin or cyclone separator in a dishwasher or washing machine.
2. Rinse the dustbin and cyclone separator with cold water until
clean.
3. Leave the dustbin and cyclone separator to dry for 24 hours or
until completely dry.
* Clean as needed