Rocket Fish RF-BTAPDT RF-BTDGLE User manual

Bluetooth 2.0 EDR Class II Wireless
USB Adapter
RF-BTAPDT
User Guide
RF-BTAPDT_08-1733 ENG.fm Page 1 Thursday, October 16, 2008 2:31 PM

2
Rocketfish RF-BTAPDT
Bluetooth® Wireless
USB Adapter
Contents
Introduction ................................................................. 2
Features ......................................................................... 2
Using the Bluetooth adapter ................................. 3
Troubleshooting .......................................................11
Legal notices ..............................................................13
Introduction
Congratulations on your purchase of the RF-BTAPDT
Bluetooth® adapter. This Bluetooth adapter lets you connect
any wireless Bluetooth device to any computer that has an
available USB port.
Features
• Supports Bluetooth devices
• Bluetooth specification v1.2 and v2.0 compliant
• Compatible with the following profiles:
• Generic Access Profile (GAP)
• Generic Object Exchange Profile (GOEP)
• Serial Port Profile (SPP)
• File Transfer Profile (FTP)
• Object Push Profile (OPP)
• Dial-up Networking Profile (DUN)
RF-BTAPDT_08-1733 ENG.fm Page 2 Thursday, October 16, 2008 2:31 PM

3
RF-BTAPDT
• Synchronization Profile (SYNC)
• Fax Profile (FAX)
• Personal Area Networking Profile (PAN)
• Human Interface Device Profile (HID)
• Headset/Audio Gateway Profile (HSP)
• Hardcopy Cable Replacement Profile (HCRP)
• Basic Imaging Profile (BIP)
• Basic Printing Profile (BPP)
• Generic Audio Video Distribution Profile (GAVDP)
• Advanced Audio Distribution Profile (A2DP)
• Audio Video Remote Control Profile (AVRCP)
Refer to the device’s user guide for additional
instructions and security codes.
Package contents
• Bluetooth® Wireless USB Adapter
•InstallationCD
•UserGuide
System requirements
• Intel® Pentium® processor (or equivalent)
• One available USB port (USB 2.0 or 1.1)
•CDdrive
• Operating system: Microsoft® Windows® XP with Service
Pack 1 or higher, or Microsoft® Windows® 2000
Using the Bluetooth adapter
Installing the Bluetooth software
This procedure assumes you’re installing the software onto a
Windows XP computer.
RF-BTAPDT_08-1733 ENG.fm Page 3 Thursday, October 16, 2008 2:31 PM

4
To install the Bluetooth software:
1Plug the Bluetooth adapter into an available USB port on
your computer. If you forget to connect the adapter to
your computer before installing the software, a warning
message will appear during the software installation.
2Insert the provided installation CD into the CD drive on
your computer. The Bluetooth installation program runs
automatically, and the Welcome dialog box opens.
If the program doesn’t start automatically, open
Windows Explorer and run the file setup.exe on the
installation CD.
3Click Next.
4Read the agreement, click I accept the terms in the license
agreement, then click Next. A dialog box opens that shows
you where the program will be installed to.
5To install the program to a different location, click Change,
then type the correct location.
6Click Next.
7Click Install. The program is installed.
RF-BTAPDT_08-1733 ENG.fm Page 4 Thursday, October 16, 2008 2:31 PM

5
RF-BTAPDT
8When the “Driver Signature Notice” message appears,
click OK.
9If the “Bluetooth device not found” message appears,
plug the Bluetooth adapter into an available USB port,
then click OK.
The Found New Hardware Wizard installs software for
the USB Bluetooth adapter. Installation may take several
minutes.
Setting up the Bluetooth software
To configure the Bluetooth software:
1Double-click My Bluetooth Places on the Windows desktop,
or click the Bluetooth icon in the system tray.
The Initial Bluetooth Configuration Wizard starts.
RF-BTAPDT_08-1733 ENG.fm Page 5 Thursday, October 16, 2008 2:31 PM

6
2Click Next.
3Enter a name, then and click either Laptop Computer or
Desktop Computer from the drop-down menu for this
computer.
4Click Next, then click Next again.
5Click to select the services that this computer will offer to
other Bluetooth devices, then click Next.
RF-BTAPDT_08-1733 ENG.fm Page 6 Thursday, October 16, 2008 2:31 PM

7
RF-BTAPDT
6If you have another Bluetooth device, click Next.
Otherwise, click Skip.
7When the configuration is done, click Finish.
8Insert the Bluetooth adapter into your computer, and
wait for the adapter’s LED to turn blue before connecting
to any Bluetooth device.
Connecting to a Bluetooth mouse or keyboard
Before the Bluetooth mouse or keyboard pairing, make sure the
following:
1Make sure that the Bluetooth software has been installed
and configured according to the instructions in this
guide.
2Make sure that the batteries for the mouse or keyboard
have been correctly installed and are fully charged.
3Make sure that the USB Bluetooth adapter has been
plugged into your computer.
4If you are connecting a mouse, turn on the mouse power.
See the mouse’s user guide for instructions.
RF-BTAPDT_08-1733 ENG.fm Page 7 Thursday, October 16, 2008 2:31 PM

8
5Press the Connect button on the mouse or keyboard, then
press the Bluetooth adapter’s Connect button until the
adapter’s LED flashes blue and the following screen
appears.
The software starts the search.
Connect button
RF-BTAPDT_08-1733 ENG.fm Page 8 Thursday, October 16, 2008 2:31 PM

9
RF-BTAPDT
6If the following message appears, no Bluetooth mouse or
keyboard was found.
Make sure that you have pressed the Connect button on
the device to make it able to be seen by the computer. If
you are trying to connect a mouse, make sure it is turned
on. The search starts again in a few seconds.
7When a Bluetooth mouse is detected and the following
confirmation message appears, click to confirm that the
mouse is connected.
RF-BTAPDT_08-1733 ENG.fm Page 9 Thursday, October 16, 2008 2:31 PM

10
8When a Bluetooth keyboard is detected and the
following Security Setup screen appears, use the
connected Bluetooth keyboard to type the digits shown
on the screen, then press Enter. The keyboard is
connected.
Note: The Bluetooth security code is randomly generated
each time.
Connecting other Bluetooth devices
To connect Bluetooth devices suchas printers, modems, and PDAs:
1See the guide that came with your Bluetooth device for
instructions on making them able to be seen by the
computer (in “discoverable mode”). Often this involves
just turning on the device and pressing a Connect button.
RF-BTAPDT_08-1733 ENG.fm Page 10 Thursday, October 16, 2008 2:31 PM